Jump to content
 
  • entries
    109
  • comments
    358
  • views
    144,925

"Not Impress-Flo"

S.A.C Martin

Entry posted by S.A.C Martin

1,746 views

 Share

blogentry-1656-090733600 1288636855_thumb.jpg

 

I used to love Airfix kits. I used to build them all the time when I was younger. Stopped at around the age of twelve, because I was into my sport and training most of the time. Athletics is as athletics does. I'm not very athletic now!

 

The last time I made an Airfix kit, I built a model of a Lancaster Bomber, specifically a 617 Squadron aircraft (though not with the bouncing bomb attachment). It was pretty good, neat in its paintwork, but crucially had been aided with a decent set of instructions, and what was a very well designed plastic kit. Patience normally helps too!

 

On this occasion, my patience has just about run out. I've been building a rake of Dapol Presflos to run on the Copley Hill set. In theory, this would be cheaper than the Bachmann model by half, and run "almost as well".

 

Cue canned laughter. I was wrong - hands in the air - it would have been more expensive to buy Bachmann, but it would have saved me some angst!

 

First off, the instruction diagrams are terrible (not to mention wrong, for one thing, but we'll come onto that later). The diagrams are simply photocopies of an original drawing, and very coarse (see above picture - very rough pictures!)

 

The instructions themselves aren't bad, everything is numbered on the sprue, but this presents a problem in that half the kit will be damaged when you go to open it.

 

I'm not joking - I've built nine of these presflos this week. Every single kit has had a dozen or so bits broken off, badly bent, or in need of careful bending under temperature (the instructions recommend warm water). Here's an example:

 

blogentry-1656-000296800 1288636878_thumb.jpg

 

Which brings me onto my next point - the chassis construction. Two flimsy buffer beams and very warped side panels, expected to be glued together with the wheels fitted between the axleboxes. I tried this for the first Presflo, and it was infuriating. Even sticking one side down with blue tack, or using my traditional holding implement, clothes pegs, couldn't keep the whole chassis together while it was gluing. In the end, I changed tack - built the whole model, minus the wheels, and carefully popped the wheels in at the end. Eight out of nine models done this way, and unlike the first, no breakages, bending or similar to speak of when I did this.

 

blogentry-1656-063592200 1288636909_thumb.jpg

 

So my advice is to ignore the "add wheels" instruction - numbered 3 in the list of instructions - and fit the wheels at the end.

 

Overall, the kit (whose origins are, I believe, in the Airfix range from eons ago) fits badly, requires great amounts of filing and preparation to put together, and once or twice nearly put me off continuing with the builds altogether. Perhaps the most frustrating thing is the price and look of the model - people will buy this, thinking its a suitable "starter" or "simple" kit for the kids - think again.

 

If you've the patience, then it scrubs up well, but running is wholly dependent on whether or not the chassis - like at least five of mine are - is modified with better bearings in the axleboxes than the moulded plastic. For a few quid, and some vast amounts of patience, you can make the kit work, but overall I'm left wondering if we're missing something in the railway world, that the world of model aircraft clearly has managed - kits with durable, easy to fit together pieces, and decent instructions that won't put a younger generation off kit building.

 

Strange thing is - I built a Dapol Battle of Britain plastic kit a few years back and it didn't seem to have the problems this had. Strange, very strange.

 

blogentry-1656-066986100 1288636932_thumb.jpg

 

So, two Presflos down from the paintshop, and due to be finished with all their decals, followed by weathering - and another seven to go into the paintshop, etcetera, etcetera...

 

Until next time - and apologies for lack of updates. Job hunting tends to take away the time for modeling...

  • Like 1
 Share

3 Comments

Recommended Comments

dibber25

Tools that are 50 years old - and a kit that Airfix always supplied in a box for better protection, no doubt.

  • Like 1
Link to comment
Andy Y

You'll get a better product by scouring auction sites and secondhand stalls for the original Airfix kit where you'll get a cleaner and better fitting product. Current Dapol wagon kit offerings are best avoided.

  • Like 1
Link to comment
S.A.C Martin

Tools that are 50 years old - and a kit that Airfix always supplied in a box for better protection, no doubt.

 

Yes indeed - the older cardboard boxes would have stopped half the damage these kits I've built, had when opened.

 

You'll get a better product by scouring auction sites and secondhand stalls for the original Airfix kit where you'll get a cleaner and better fitting product. Current Dapol wagon kit offerings are best avoided.

 

I must confess Andy, I was on the lookout for the older kits, or second hand Dapol RTR Presflos - but these were £3 in the MHR shop, and I thought, what the hey...support the railway. I'd do it again mind, spending a few quid in the shop, but not on these kits. The quality of the plastic is terrible, particularly the side-frames, as previously mentioned. I will do as you say, now, because while the Bachmann Presflo is a stonking model, I can't shell out £9 a time for a single wagon to make up a rake.

 

Not until I've got a job anyway! :lol:

 

It's a shame Hornby haven't thought of doing their own railway kits with the Airfix brand name. I wonder how many of us would be tempted if they made a new railway kit range...

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...