Narrow Minded Posted April 17, 2017 Share Posted April 17, 2017 (edited) I thought it might be of general interest, but especially useful for newcomers and potential live steam owners to have a chat about what we have in our "steam up boxes" - the stuff we all take for granted, but would be stuck without I'd personally be especially interested to see anything that I haven't previously thought of having, but would want to add to my own collection In no particular order, I have.... a little 'toolbox' including a multi-tool with snipe nose pliers and an assortment of tools A refillable lighter and a couple of spares (people always borrow lighters at steam-ups!) A couple of boiler filling syringes and a handy size container for the filtered rain water (make sure the syringe fits as shown in the photo) A collection of 3 link coupling chains, lamps and headboards Spare batteries for the working lamps, and connector clips for R/C battery packs (I lose em) Gas can adaptors - for 'screw top' and 'push fit' types and of course the fuel supply itself Steam oils (both of the recommended grades because I run Accucraft and Roundhouse loco's) and lubricating oil for the motion A "shunters pole" - for coupling the 3 link chains, but also useful for reaching the regulator inside the closed Roundhouse cabs, fishing out errant bits of ballast etc A "rolling tin" which carries a "Rolling Road", so I can carry out any fault finding without occupying the track at a steam-up Last but not least, a selection of rags for wiping down loco's, hands etc Unless I've taken something out and forgotten it, that's the contents of my box, have you got anything else in yours ? Edited April 17, 2017 by Narrow Minded Link to post Share on other sites More sharing options...
Owd Bob Posted April 18, 2017 Share Posted April 18, 2017 You forgot to show the wheelbarrow you use to push it all around in! Looks like i've a lot of stuff to start collecting now. Many thanks NM it's all very helpful & informative. Link to post Share on other sites More sharing options...
Narrow Minded Posted April 18, 2017 Author Share Posted April 18, 2017 Doh! I knew I'd forgotten something............ Water Top up bottle ............ and all the "tools" go in a handy box (17"x12"x4") while the water, oil and gas go in a slightly smaller bag with a shoulder strap, so there's a free hand for the loco box Link to post Share on other sites More sharing options...
DavidB Posted April 18, 2017 Share Posted April 18, 2017 That's a very impressive selection of equipment you have there NM. Is that a dental mirror (for checking that burners are alight?) alongside the spanners? I have a few other very low-tech things that I use on my line: - a homemade uncoupling hook made from thin wire for uncoupling Accucraft chopper couplings - it's just a straight length of thin brass wire with a curled handle covered in shrink wrap. A couple of my rakes of FR/WHR carriages have sprung-loaded corridor connections, which makes it impossible to access the couplings by hand, so the uncoupling hook is an essential part of my operational kit. It's also helpful for other stock where I have removed or altered the Accucraft chopper housing to reduce the distance between vehicles, and there simply isn't the space for me to reach in by hand to lift the hooks. - an old tapered needle-file with the tip ground down so that it fits neatly into a slot in a safety valve for making adjustments. The handle is a piece of wooden dowel which is useful on the rare occasions when a safety valve won't reseat completely - a quick tap from the dowel always does the trick. - a feather from one of my bantams. The quills are exactly the right size for clearing out flangeways and crossings. As the bantams often cause the blockages in the first place (by scratching up the ballast while foraging), it seems only fair to use their feathers to clear the track again. David Link to post Share on other sites More sharing options...
Narrow Minded Posted April 18, 2017 Author Share Posted April 18, 2017 Thanks David, I dunno about "impressive", but it just grew over the years as things I found I 'needed' but didn't have readily to hand got transferred from the general toolbox and into the kit, Yep, that's a small mirror for checking the wicks are alight on the old Lady Anne - though usually you can tell if one's out by holding a hand over the loco. Corridor connections and shortened choppers aside, a shunters pole (uncoupling hook) just makes the job so much easier - I struggle without it with just plain old 3 link chain & hook couplings! I must get round to making a safety valve adjuster! I've had an old screwdriver sitting around for years waiting to be converted. At the moment, I use the snipe nose pliers, which aren't ideal, so thanks for the nudge on that one. I used to give the SV a "quick tap" if it wouldnt stop feathering, but got a severe Tutting from an 'old hand'. Since then I've done the opposite and given it a lift with the pliers and let the spring snap it back down in position. Great idea having the culprits contributing to clearing the flangeways. 2 Link to post Share on other sites More sharing options...
RMweb Gold LH&JC Posted April 19, 2017 RMweb Gold Share Posted April 19, 2017 A tool I've recently added to my kit is a beer bottle top, it's the right size to sit on top of a chimney and stop a loco impersonating a fountain. I know chuff pipes stop fountain impersonations as well but I prefer the more natural sound of a loco without one. 2 Link to post Share on other sites More sharing options...
Narrow Minded Posted April 19, 2017 Author Share Posted April 19, 2017 Sounds like a valid excuse to carefully remove a beer bottle top and give it a try (after making sure the beer doesn't go flat - "cheers!") I'm a fan of the chuff pipes myself, and will be ordering one for my latest acquisition, but it'll be a while yet as there are other mods I need to finance first. I was prepared to go back to the 'pre chuffer' days and put a folded rag over the chimney until any priming had cleared, but a handy bottle of Abbot will let me try your suggestion out ta! Link to post Share on other sites More sharing options...
RMweb Gold vjoneslong Posted April 24, 2017 RMweb Gold Share Posted April 24, 2017 Nice shunters pole NM. Where did you get yours from? My steam up toolbox is rather sparse in comparison. Oil, lighter, and my shunters hook (torch with brass hook added) and thats about it! Link to post Share on other sites More sharing options...
Owd Bob Posted April 24, 2017 Share Posted April 24, 2017 You'll have to enlighten me as to where and how you get the filtered rainwater NM, 'cos using the right type of water is not something i had thought about before.. Link to post Share on other sites More sharing options...
RMweb Gold vjoneslong Posted April 24, 2017 RMweb Gold Share Posted April 24, 2017 You'll have to enlighten me as to where and how you get the filtered rainwater NM, 'cos using the right type of water is not something i had thought about before.. I use a water butt connected to the guttering on my shed. I then run the water through some coffee filter paper which removes all the muck before I use it. Simples! Link to post Share on other sites More sharing options...
Narrow Minded Posted April 24, 2017 Author Share Posted April 24, 2017 I use a water butt connected to the guttering on my shed. I then run the water through some coffee filter paper which removes all the muck before I use it. Simples! Pretty much the same, but my water butt is "free standing" - I found I was getting too much detritus washed off the shed roof and guttering. Just having an open top allows plenty of rainwater to be caught. I saved up a collection of empty windscreen wash / anti-freeze etc plastic containers and fill them then store 'em in a dark corner of the shed (direct sunlight will encourage algae) A plastic funnel lined with "J Cloths" and coffee filters is used to transfer 'stored water' into the 'loco' water bottle - filtered and ready to use. We actually live in a good area for tap water, (check the insides of your kettle...... if you've had it a good while and you use it frequently and there's no scaling inside, you're good to go), but I prefer not to risk it. Oh, and the Shunters Pole is obviously some sort of dental tool, and it turned up on a car boot sale table! There's also been a LOT of debate on whether de-ionised water is safe to use, but again, for the sake of gathering up some free rainwater and running it through a filter, why risk it? Link to post Share on other sites More sharing options...
Owd Bob Posted April 24, 2017 Share Posted April 24, 2017 Very useful! Thanks Men! Will melted snow do the same job? its easier for me to catch Link to post Share on other sites More sharing options...
44690 Posted May 25, 2017 Share Posted May 25, 2017 (edited) Interesting list of bits 'n' pieces. FWIW I also take spare batteries as my loco is R/C. I get my water from our condenser tumble drier. Filtered to remove anything suspended in it and stored in old plasic milk bottles. Our tap water would probably be ok to use as we've had our kettle for years and no residue or limescale. I'd still filter it though to be on the safe side. Ian Edited May 25, 2017 by 44690 3 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now