Jump to content
 

Recommended Posts

Hi,

I design and build lasercut buildings, specialising in prototype designs. Much of my work is bespoke for specific orders but since September last year I have started a small increasing range of buildings and asessories.

I'll post completed buildings ready to purchase and answer any questions you may have.

 

post-1485-0-35537900-1495107411_thumb.jpeg

 

1718295115_IntentioAdvert(VirtualShow).jpg.c14b38ec129920049b91c5e4d22e341c.jpg

 

To kick this off, chimney stacks complete with pewter pots.

post-1485-0-85122900-1427146737_thumb.jpg

post-1485-0-07819600-1427146832_thumb.jpg

Weighbridge with user definable option to fully personalise to your chosen railway company.

post-1485-0-41836000-1427147145_thumb.jpg

An example of corner joints.

post-1485-0-74995700-1427147046_thumb.jpg

GCR Platelayers hut

post-1485-0-02457100-1427147342_thumb.jpg

Edited by BrushType4
  • Like 8
Link to post
Share on other sites

Some great pieces there Phil trying tp put a generic order together for some pieces to go along with some of my builds..

I need an outside chimney, do you do the one you have for the yard hut as a separate item, not yet looked through you shop details closely yet..

Link to post
Share on other sites

  • 4 weeks later...

Thanks Steve.

 

Some of those letters are only 1mm tall. It's given me the idea to produce custom designs to represent the cast iron signs seen all over the railway network back the day.

 

Also street names too.

Link to post
Share on other sites

Hello Phil

 

Gardening chores are getting in my way [less modelling time] these days but I have been paying paper trains on tea breaks etc. 

I see you have some single & triple arches and some promised single and double track tunnel/bridge mouths.  Will they all match in height and are the latter available yet..

 

I'm paper playing for my scenic break to fiddle yard and fancy some arches, walls ,tunnels and buttresses and am looking for some unanimity of the wall heights as I want to run a pipe bridge across them too.

I estimate I would want in order from the baseboard back 1x blank arch - 1x single track mouth -  1x blank arch - 1x double track mouth - 1x blank arch - 1x single track mouth - 2x 3 panel. Arches.

 

These will run at a 60 degree angle to the back edge with the blank arch following the double track mouth turning to run parallel to the board front with the last single mouth turning back to cross over only one of the tracks.

The double track will split through the double mouth one to fiddle the other to in view head shunt which will run in front of the 2 x 3 panel arches.

 

Well that's the paper plan anyway. :sungum: :jester:

 

sketch like.>>>

post-1159-0-37466000-1429743048.jpg

Edited by Barnaby
Link to post
Share on other sites

Hi Mark,

 

The arches and bridges are available and i'll post up pictures as soon as I can. Unfortunately they are based on prototypes and so do not exactly match. I could as a one off make a run for you to fit your space and match up height wise. 

 

Let me know and have you worked out what you need chimney wise yet?

Link to post
Share on other sites

Thanks Phil I'll have a look at what I can confirm so we can get my order under way.  Do you have the sizes for the bridges single and double track and what are the depth options you refer to?   Once I get them I can check from my baseboard if they will fit as I intend them too.

 

I can also work out the remaining walling lengths which blind arches could do as would plain walling with support buttresses spaced every 25 - 30ft if you make such beasts?   That 25 - 30ft figure is a "feel right" and not an exact measurement fact, I'll need to check the buttress repeat spacing to be certain.

 

That's tomorrows tea breaks reading/planning material taken care of.  

 

Best

Link to post
Share on other sites

  • 2 months later...

 

Some very nice products here. I can see a use for the warehouse parts in one of my projects. Are you intending on doing any more bits?, I'm thinking initially of plain wall sections and some sort of parapet sections to finish off the top.

Link to post
Share on other sites

Some very nice products here. I can see a use for the warehouse parts in one of my projects. Are you intending on doing any more bits?, I'm thinking initially of plain wall sections and some sort of parapet sections to finish off the top.

Yes, there will be a complete range of parts including loading bays, roof details etc.

  • Like 2
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...