My plans for Basuto Quay are still developing, and I am working on the track plan in Templot. In the meantime, I am also doing a bit of wagon construction - the latest being a diagram V12 covered goods wagon.
The starting point is the Peco (ex Webster) kit, which is for the V18 type. I have backdated it to the earlier diagram V12 as the V18 is too late for my period - and in any case I couldn't resist those end louvres. The conversion makes use of cast resin replacement ends by Inver
Most of the wagon builds I have posted on this blog have been either based on kits, modified to a greater or lesser extent, or (in one case) scratch-built. This one is different, being based on a 3D print by Stephen @stevel, who has posted about some of his work elsewhere on RMweb. Stephen has been developing his digital model for this prototype over the last few months, with some input from me - mainly providing information from books and drawings Stephen doesn't have access to, and providing f
This diagram P4 ballast wagon was an eBay purchase, cheaply bought as a 'fixer-upper'. It's built from the PECO (ex Websters) kit, and the original builder had made a reasonable job of construction. The paint finish wasn't great, with a fair amount of dust in it, and the brake gear was smashed:
The first job was a good clean up, and remove the broken brake gear and couplings - the buffer rams had to stay in place, as the retaining parts on the rear of the rams were very
There is a photograph in Jim Russell's book 'GWR Wagons Appendix' that shows a wagon loaded with long, thin conifer tree-trunks, of the kind referred to as 'Norway poles'. For some time I have wanted to model a similar load.
The wagon itself has been described in this blog before, and has a rather chequered history. Amongst other issues, I put washer plates on the inside, corresponding to the attachment points for the sheet supporter mechanism at each end. I was following the RCH dra
I have just finished making an LNWR 4-plank open, to diagram 84. This was meant to be a "quickie", as a relaxing diversion following the complexities of the horsebox and before getting my teeth into a brake van. However, it has taken three months - partly due to a lack of modelling time recently, and partly because it turned out to be a bit more involved than I had expected.
The starting point was the ABS whitemetal kit. My first impression was - it's enormous. The prototype was 18 feet ove
The iron covered goods wagon, codename 'Mink', is a familiar, perhaps even iconic, feature of the GWR from 1886 onwards. Less well known is the small number of vehicles built with a standard iron mink body but passenger-rated running gear, akin to that of horse boxes of the time. Details can be found in the HMRS publication All About GWR Iron Minks by JH Lewis et al., which has a drawing and a couple of photographs.
Originally intended for use on branch line passenger services, they
A PO wagon with a difference, in two ways: the livery is fictional, and it wasn't built by me, but by my father, Bill.
The underframe is Slaters, and the body is scratch-built in plasticard. The lettering is hand-painted using - if I remember correctly - Humbrol enamels.
Dad spent most of his career as an airline navigator, flying long-haul, which meant he would often be away for a week or more. In the early days he enjoyed seeing the many places he flew to and socia
So this is where I left it last time - the basics of the underframe, running gear and body complete, but a lot of detail to go:
Detailing on the sides and solebars came mainly from Ambis etches. The document box is an ABS casting, and the horse hook is a piece of wire for the loop, and plasticard for the base.
The bolt ends on the underframe are from plastic rod as before, including the strap bolts that pass through the headstock. I am not aware of
This wagon is a 'first' in two respects: it is my first wagon with Scaleseven wheels - though it didn't start that way - and it is my first scratch-built wagon in 7mm scale (and for at least 30 years...). The build was also at several points an object lesson in why one shouldn't assume, as we will see.
If it is a scratch-build, where to start? There's not kit to work from, respond to or rebel against. There are not, as far as I know, detailed drawings for these 1-plank wa
This time I am returning to that ubiquitous item of the early 20th century railway, the private owner coal wagon - in this case, a 6-plank end-door type built by Gloucester RCW, in the livery of 'United' collieries. The model is of course the familiar Slaters kit, and so is very similar to a build to the 'Ocean' wagon I have posted about previously:
The big difference with this one is that it is empty, not loaded, so there is full interior detailing needed, and that is the fo
What's that you say? Another GWR 4-planker? Haven't you had enough of those? Well, if you're sure...
This is 41211, freshly turned out in 1908 style: grey paint with 25" lettering, axleboxes upgraded to oil types, and a sheet supporter fitted. All the latest features of a truly modern merchandise wagon of the new century, in fact - Swindon has played its A-game. Not so, unfortunately, the folks who have loaded it. The rather filthy sheet has been put on crooked, obscuring
The GWR adopted iron, and later steel construction for underframes quite early, compared to most other railway companies. For reasons of variety and aesthetics, I wanted to have a mix of wooden and metal underframed wagons, and my 1908 period was partly chosen for this reason - there were still a few GWR wooden underframed wagons around.
One such is this 2-plank open, built from the WEP etched brass kit. Overall, it is a nice kit, and I built it pretty much as intended, b
Locos need coal. I haven't started building the loco stock I will need for Netherport, but I thought I would get ahead by building a loco coal wagon.
Slaters offer a kit for a 10T example, which claims to be a diagram N13 - ideal for my 1908 period. However, there are some significant issues with the kit, most notably that it has square corners with riveted angle-iron reinforcement, while the prototype had round corners with no reinforcement. Later types had square corner
You will be pleased to know it isn't all GWR 4-plank wagons here...
Netherport's imagined location on the Dorset coast is in LSWR territory as much as GWR, so any non-GWR wagons being seen at Netherport are more likely to be LSWR than anything else. Looking at the local geology, it seems the nearest area with clay suitable for brick-making would be to the east of Netherport, and served by the LSWR, so this 3-plank open is bringing bricks for construction work in the town.
Yet another GWR 4-plank! This time in grey livery, and with a load of large casks:
The wagon itself is a standard Peco kit, which I got on eBay as a 'rescue' wagon - it had been built reasonably well but painted poorly. I scraped most of the paint off the main flat areas, and repaired a partly broken W-iron. I removed the compensated wheel-set in the process, which turned out to be quite useful later on.
I also upgraded a few parts - firstly the da
For my 1908 GWR setting, I can't have too many 4-plank opens - they were around 40% of the revenue-earning fleet. My planned rosta of 20 GWR wagons therefore includes eight 4-plankers, and it is another one of these that is the subject of this post. It differs from the last one in being made from the ABS whitemetal kit (remaining stocks still available from DJ Parkins). It also has a load of straw under a sheet - inspired by Mikkel's similar creation in 4mm scale.
The kit
This post covers something a bit different to the previous wagons - not a kit, but an upgrade of the RTR Iron Mink by Minerva.
In many ways, the model is very good as it comes. The detailing is crisp and fine, and overall it captures the feel of the prototype. There are a few weaknesses:
the roof on the prototype is sheet metal, so the edge of the overhang is very thin - just the thickness of the metal. The model has the roof moulded in plastic of course, so the roo
This post continues the story of the sheeted 5-plank GWR diagram O4 wagon.
The sheet was made of normal printer paper, with the lettering printed on with a laser printer, and backed with a self adhesive aluminium foil.
The first stage was to use the artwork provided by forum member Ian Smith for the sheet lettering:
Note that this is the 1903 design - Ian has also done the earlier design, around 1900, should you need it:
Ian's artwork provides a full set of digits, s
There is quite a lot to say about this next wagon, so I am splitting the write-up into two parts - this post will look at the wagon itself, and the next post will describe the wagon sheet (sheet being the correct railway term for what in everyday language we might call a tarpaulin).
The starting point is the Slaters (ex Coopercraft) kit for a diagram O4 5-plank open. It's a nice kit, with good detail and crisp mouldings. There are some inaccuracies and opportunities for improvement,
Well, the comments section of the last post took us down some interesting and delightfully esoteric byways, regarding the patenting of sheet supporters...
This post will perhaps be more straightforward, though hopefully it will include a few things of interest - its about a Slaters kit for a private owner wagon, 'Ocean':
This kit was bought as part of a lot of three wagon kits on eBay - they were all old kits, but unstarted. The price was not a bargain, but reasonabl
For this first wagon build write-up, I thought I'd start with this GWR 4-plank. For my 1908 period, these represented around 40% of the GWR wagon fleet, so I can hardly have too many. Certainly, whenever I add something exotic, such as a Macaw bolster wagon, I probably need to make a couple more of these...
Given that I need several of these 4-plankers, it is very handy that PECO make an excellent 7mm scale kit for them. The mouldings are crisp, well-detailed and fit toge