Jump to content
 
  • entries
    66
  • comments
    43
  • views
    19,850

About this blog

When ignorance is not always bliss and improvisation has its cost

Entries in this blog

Railway Model shops in London

Hi all! This is probably not the best place to request information, but in view of its nature, I don't know where to place it. I need to have the names, addresses and e-mail adresses of model railway shops in London with good repair facilities for Hornby models. Can anybody help? Thanks in advance
petertg

petertg

0

Progress(?) report

What is progress? Is it having more on your board than you had before or is it that some things that didn’t work well now work a bit better? I had to replace a surface mounted point motor. Previously all units had passed well, albeit by a hair’s breadth. After replacement I discovered that the non-powered driver car of my push-pull double deck commuter rake (the first double deck units introduced by RENFE prior to the genuine EMUs) was hitting the motor. The point in question is situated right
petertg

petertg

0

Progress(?) report

What is progress? Is it having more on your board than you had before or is it that some things that didn’t work well now work a bit better? I had to replace a surface mounted point motor. Previously all units had passed well, albeit by a hair’s breadth. After replacement I discovered that the non-powered driver car of my push-pull double deck commuter rake (the first double deck units introduced by RENFE prior to the genuine EMUs) was hitting the motor. The point in question is situated right
petertg

petertg

0

Practically at a standstill

Hi all! Since before Christmas I have been able  to do nothing. The Christmas period was spent in part away from home and then occupied with family events. Then in January I had vascular problems in both feet and the specialist had me shut up in hospital for twelve days. I still have problems and difficulty in walking due to a constant pain in the lumbar region. The cold weather and lack of a suitable heater make working in the garage difficult.  However, since this web is for airing modelling t
petertg

petertg

0

Posible movements

I have been quiet for a while because my layout is at a standstill, mainly due to my not having been able to replace the hoisting pulleys I wanted to change way back last November and also due to the fact that it is cold in the garage where the layout is suspended. With a bit of luck, there may be some new movement the weekend of Feb. 28-Mar. 1 and the new pulleys installed. I also have to replace a burnt-out point motor. That will leave a few blank places to be filled with appropriate scenery a
petertg

petertg

0

Plodding on and still learning the hard way

I have been writing up this contribution bit by bit for nearly a month now (editing as and when necessary), but since progress has been slow for various reasons, not all related to the layout itself, I have decided to make a post. I am an assiduous reader of almost all of the blogs and, while it is no great consolation, it is encouraging to see that more experienced modellers make mistakes and confess them. Since I am basically optimistic I refuse to give up unless I am absolutely forced to and
petertg

petertg

2

Playing trains

Hi all! As stated in my last post, after nearly seven years of messing about with my layout (and messing it up), I have now reached the state where I can seriously think about “playing trains” So I got various models out of their boxes and, after cleaning the track with IPA (which, to my surprise, is sold at chemists here) I started trying them. The result is that my Bachmann DMUs (Class 108 and 156) performed reasonably well although the 156 derailed two or three times at the same turnout in
petertg

petertg

0

One step forwards, more backwards

I have been hanging on since my last contribution hoping to be able to report some real progress but, far from that, I have to report regress (i.e. retrogression). I have mentioned elsewhere my problem with arthritic fingers and the risk of hitting the wrong lever of the passing switches for the point motors, with the risk of damaging the motors. I replaced two damaged motors and, furthermore, installed pushbutton switches. These are supposed to give feedback information via leds but do not do s
petertg

petertg

0

One hard task finished

Good evening all. Two and a half years after relaying the track I have finally finished the ballasting. Unfortunately, in spite of my efforts, it has not been a tidy job, in fact it is rather messy, but it is the best I have been able to do. Some of the earlier work will need touching up but, after a clean up, I can start start fixing down certain buildings and other scenic items now that they don't represent an obstacle for working. The engine shed will not be a fixture, since it will surely ha
petertg

petertg

0

New platform

I mentioned in my last post that I was building an additional new platform so that I could have two trains running simultaneously and both would have where to pick up and set down passengers as required or otherwise one would have to run continuously with nowhere to stop. I can now report that the new platform is in an advanced state and enclose some photos of its construction. In the first place I would point out that do not have any CAD program, silhouette or laser cutter, 3D printer or instru
petertg

petertg

0

New material received

Further to my post of last Friday, I have received the new material, the Jinty was pre-owned and i decided to have the chip hard wired by Hattons themselves since it is becoming increasingly difficult for me to handle very small parts like the screws used to hold the bodies in place on the chasses and other small accessories. I fitted both the autotrailer and the locomotive with kadee couplers, put a composite brake coach between them and set them running. The whole outfit runs very smoothly. I
petertg

petertg

0

More sessions of fitting Kadees

As mentioned in a previous post, around July last year i came to the conclusion that my UK 00 fleet was very poor in comparison with my continental H0 fleet. Namely, I had two DMUs, three steam locomotives and only four passenger coaches. So, I lashed out and purchased four passenger coaches (Dapol) and seven goods vehicles, all Bachmann. I had the idea of fitting them all with Kadee couplers. I managed to fit them to the passenger coaches with some trouble, since these did not have the NEM pock
petertg

petertg

0

Lima Collection - Trams

In October, my wife and I had a holiday in Geneva with a daughter who was working there with the WTO. On the Saturday, she took us to the flea market where there was a lot of rubbish on offer, but one lady had 3 or 4 of the Lima Tram collection. I didn't buy then, because I wasn't quite convinced of its suitability for my layout. Nevertheless, a few weeks later another daughter went to see her sister in Geneva and I asked them to buy one for me, It is the Düwag Partywagen, nº 208041 as shown bel
petertg

petertg

0

Last minute snag

Evening all: This morning I had high hopes that to-day would see the finish of work on the underside of the baseboard. But there is still one problem bugging me. I can't get the station lights to work properly. My street lighting works, the yard lights work, but not the station lights. The funny thing is that if I apply the current from what should be the head end of the wiring there is no response, but if I apply current from the tail end, then they do light up. So, the obvious solution is to
petertg

petertg

2

Just plodding along

I sometimes wonder if what I post is of interest to anybody but me. Some people are building kits, others are making attractive dioramas, etc. but I am doing nothing of that. When I think I am getting somewhere another hitch occurs. At the beginning of summer, after a couple of weeks of hectic work to install the new operating system for my point motors I found that one of them did not switch, Since prior to doing the final wiring I had tested the motors one by one and they had worked, my conclu
petertg

petertg

3

Just expressing my feelings

Hi all again! Since I can’t make any positive movement forward on my layout, I feel I must let off steam with this note. I have a list of jobs to be done: 1. Improve the lighting in the garage, not only for better illumination of the layout, but also for all uses of the garage. 2. I have to replace four pulleys of the hoisting system which do not rotate when the baseboard is being lowered or raised. Fortunately the cords used are Kevlar mountaineering cord which seems to resist the friction a
petertg

petertg

2

I am still alive, in spite of all.

I have just realIised that six months have passed since my last post and a lot of things (not all pleasant) have passed in the meantime. To be brief, In May I was rushed into hospital with a lung edema (lings full of blood) and was discharged a week later with a new addition, namely a stent. Then I had a couple of short visits (a few hours each time) for a nose hemorrhage and a heart block). On the pleasant side, there was a trip to the UK to visit relatives and old friends (in spite of my age a
petertg

petertg

0

I am still alive, in spite of all.

I have just realIised that six months have passed since my last post and a lot of things (not all pleasant) have passed in the meantime. To be brief, In May I was rushed into hospital with a lung edema (lings full of blood) and was discharged a week later with a new addition, namely a stent. Then I had a couple of short visits (a few hours each time) for a nose hemorrhage and a heart block). On the pleasant side, there was a trip to the UK to visit relatives and old friends (in spite of my age a
petertg

petertg

1

Hope renewed

I have decided to add a new piece to my blog although, after reading all the blogs where people build all their own stuff I get the impression that, in football terms, you all are in the Premier League and I am low down in a half-holiday league (if such thing still exists).   However, being no angel, I will rush in. I want to update my DCC equipment but I can't make the investment until it is reasonably possible to play trains with what I have got and it seemed that the track was still full of
petertg

petertg

1

Hallelujah

Hi all! I think to-day that I can safely say, after nearly seven years, that work on the underside of my baseboard is finished. There is one detail that I cannot finish for the time being. It is a motor that requires AC and, since I have converted everything else to DC, it will not work. Perhaps when I can purchase a new, more complete controller than my current start set. The turnouts all work and the lights also. Since I had reformed the dropper wiring I tested a locomotive, which also worked
petertg

petertg

1

Gradually getting there

Good evening all. I have been hesitating about a new post for a whle but after yesterday's events, I think I can add a bit. Tuesday was my wife's birthday and yesterday we had a family gathering (limited with two members being absent abroad and two working) with the grandchildren included. One boy got out all the mobile scenic material, i.e. buses, cars, trucks etc. and we got two trains running at the same time. The purists would have objected: there was a French locomotive hauling a motley ra
petertg

petertg

0

Getting nearer to a workable layout

Hi all! As mentioned in a previous post I replaced my 14 Vac point motor control for 12 Vdc and purchased a new controller to replace the old Piko start kit. This meant that the 14V transformer became available to power the new controller. Since, as can be seen from the enclosed images, the transformer is relatively large and was previously mounted on the baseboard, I decided that I did not want either the transformer or the controller to be permanently attached to the baseboard. So, I installe
petertg

petertg

0

Getting closer

To-day I finally managed to get the two new street lamposts correctly wired up after several failed attempts. I had got one to light up, but the other one didn't, not because it was wired the wrong way round, but because of a faulty connection and, possibly, a slight fault in the post itself.I say getting closer, because the stage has been reached where uit can be said that the layout is almost finished I suppose that you can never say that a layout is finished, because there are sdtill umpteen
petertg

petertg

0

Frustration!

As mentioned on other occasions I have problems with my Hornby 2-6-4 Stanier tank 4MT Class 4p. It just refuses to perform correctly. I have yet to be able to use it for hauling the three coaches I bought for it last year. I have managed to get it to circulate at low speed but once I up the speed a little it derails here, if not here, then there and if not there, elsewhere. I have other rolling stock that offers no problems. I have spent all this afternoon checking cambers, I ripper up part of t
petertg

petertg

0

Frustration again

Just a short note to vent my new frustration. After an exchange of comments and receiving good advice from fellow members concerning DCC track wiring and a few trials, I came to the conclusion that my wiring, albeit not perfect, was not bad and that certain anomalies observed with certain vehicles were due to the vehicles and not to the track wiring. Then, when one problem seemed solved, a new one arose. My whole point activation system (analogue) went dead. In view of the way the system is wire
petertg

petertg

0
×
×
  • Create New...