Jump to content
 
  • entries
    66
  • comments
    43
  • views
    19,847

About this blog

When ignorance is not always bliss and improvisation has its cost

Entries in this blog

Sill nowhere near finishing

The 8th anniversary of my layout is coming up any day now and the scenic work is not much nearer to being finished than it was two years ago. I have added a second signal box that the original plan required and I have a phone booth and two pillar boxes to install. Modifications have been under way on the frequently mentioned Wrenn City Class loco. At one time it seemed that it was about ready, the only thing left being to add a coupling to the tender, the original one having been removed. I hav
petertg

petertg

0

Filling the blanks

I have been doing some card modelling in recent times. I have decided that I must fill in the blank spaces on the layout soon. Like Maggie Smith in that Hotel film who did not buy green bananas because she didn't know whether she was going to live long enough to see them ripen, I have got the same feeling about the layout. So, I purchased several Metcalfe card kits: subway accesses, wooden pavilion, platform benches (two packs) and park benches. I have already assembled all the kits except one
petertg

petertg

0

Same old story

Hi all! Finished remaking all the connections, put my baseboard level again and then found that a different point motor was out of service although it seemed to work. I could hear the movement of the solenoid but the turnout did not move. I thought at first that the actuating lever could have separated from the turnout drawbar, but no. The motor had burnt out but I don't know why, since it was wired up with a capacitor. Anyway, with the system I used for connecting the motors, it will not be to
petertg

petertg

0

New material received

Further to my post of last Friday, I have received the new material, the Jinty was pre-owned and i decided to have the chip hard wired by Hattons themselves since it is becoming increasingly difficult for me to handle very small parts like the screws used to hold the bodies in place on the chasses and other small accessories. I fitted both the autotrailer and the locomotive with kadee couplers, put a composite brake coach between them and set them running. The whole outfit runs very smoothly. I
petertg

petertg

0

Gradually getting there

Good evening all. I have been hesitating about a new post for a whle but after yesterday's events, I think I can add a bit. Tuesday was my wife's birthday and yesterday we had a family gathering (limited with two members being absent abroad and two working) with the grandchildren included. One boy got out all the mobile scenic material, i.e. buses, cars, trucks etc. and we got two trains running at the same time. The purists would have objected: there was a French locomotive hauling a motley ra
petertg

petertg

0

Another one rewiring

Since my last post I have been renovating elements of infrastructure and reorganizing the wiring under the baseboard. As indicated in previous posts I have had problems with my point motor control. The Hornby passing lever switches worked O.K, but were not suitable for the present state of my fingers. The pushbutton switches used in their place were not designed for working with Hornby motors and both LEDs remained alight, whereby there was no indication of point direction. Finally, as I browse
petertg

petertg

0

Posible movements

I have been quiet for a while because my layout is at a standstill, mainly due to my not having been able to replace the hoisting pulleys I wanted to change way back last November and also due to the fact that it is cold in the garage where the layout is suspended. With a bit of luck, there may be some new movement the weekend of Feb. 28-Mar. 1 and the new pulleys installed. I also have to replace a burnt-out point motor. That will leave a few blank places to be filled with appropriate scenery a
petertg

petertg

0

An update

Good evening all!. I have just seen that it is nearly 4 months since my last post. Since then there have been events such as I got the Fowler tank to run but, as mentioned on the Forum, I cannot get it to run well through the points. In November I purchased a new Hornby R3553 and in December part of the crank mechanism fell apart. Since sending it back from here for repair under guarantee would have cost me more than twice what it cost me to have it sent out, I used devious means to have it take
petertg

petertg

0

Starting afresh

I have been silent for some time since: after an exchange of opinions on the Forum way back in February concerning dead spots, in the light of the comments made and of the fact that these comments allowed me to identify the cause of one such dead spot, I came to the conclusion that my layout had very many more potential candidates for producing dead spots. It was originally designed and built for analogue DC operation and had been converted to dcc by adding some droppers, but retaining the power
petertg

petertg

0

Getting closer

To-day I finally managed to get the two new street lamposts correctly wired up after several failed attempts. I had got one to light up, but the other one didn't, not because it was wired the wrong way round, but because of a faulty connection and, possibly, a slight fault in the post itself.I say getting closer, because the stage has been reached where uit can be said that the layout is almost finished I suppose that you can never say that a layout is finished, because there are sdtill umpteen
petertg

petertg

0

Showing some scenic progress

I have mentioned in previous posts certain advances made in the scenic decoration of my layout and would now show a few photographs. In June I posted some photographs and requested suggestions for filling in the bare spots, but none were forthcoming. So I went ahead on my own initiative. First, there was this bare corner: Which has now become this and to which I may add a few cows. Then there was this space at the other end, thus. Which has now become this after lifting the last track
petertg

petertg

0

Still alive

Hi all! Between my last post and this there have been five heart blocks and a pace maker. Fortunately for me, the last block, which lasted nine seconds, occurred when I was in bed in hospital, being monitored. Eight hours later, the pace maker was installed. Apart from this, I am struggling along with the ballasting of the track. I try to do a bit each day, but 20+ metres of track is a lot of track. Also, since I had ripped up the foam underlay and used cork, since the cork portions were hand cr
petertg

petertg

1

Ballasting

Since I relaid the whole track using cork underlay instead of the previous foam underlay I have been faced with the problem of decent ballasting. Since, for reasons explained in previous posts, I used a 5 mm thick cork, I now have the problem of how to disguise this steep step. I tried gluing 7 mm wide cardboard strips at an angle to form a hypotenuse and, in some places it seems o.k. but in others not because I did not get the ballast to stick properly. Finally, I decided to glue a twine in the
petertg

petertg

0

Some hard work done

Since my last post, I effectively refitted the point motors, then turned the layout edge on to be able to work underneath without contortions and set about getting the droppers connected to a bus. I made a query on the Forum, got some good advice and, while I did not follow it too closely, it was a a great help. After almost two weeks, in sessions of 1-1/2 to 2 hours or a bit more at a time, I to-day managed to connect the last droppers and wire up the bus wires. I still have to wire in the plug
petertg

petertg

0

Practically at a standstill

Hi all! Since before Christmas I have been able  to do nothing. The Christmas period was spent in part away from home and then occupied with family events. Then in January I had vascular problems in both feet and the specialist had me shut up in hospital for twelve days. I still have problems and difficulty in walking due to a constant pain in the lumbar region. The cold weather and lack of a suitable heater make working in the garage difficult.  However, since this web is for airing modelling t
petertg

petertg

0

Some success at last

Recently I have had some success. I had commented on the Forum that I had a runaway problem with one locomotive which the recommended solutions did not solve. I had also had a problem with the lights of another locomotive, i.e., the front headlight came on at power-up and did not go out irrespective of the direction in which the locomotive was running. Both had Zimo MX632 chips which I had bought on-line from the U.K. I took the matter up directly with Zimo and, after an exchange of e-mail corre
petertg

petertg

0
×
×
  • Create New...