The station building that fronted Freshwater Station from 1889 until it was demolished to make way for a Co-op supermarket, was the largest and grandest of the stations of the Freshwater, Yarmouth and Newport Railway. It comprised the two storey Station Master's house, with single storey booking hall, waiting rooms and conveniences, and was extended at some time to add a parcels office. It was red brick, with tiled roof rather than slates. The brickwork was quite ornate around the eaves and arou
Well, I didn't give up. At the end of the last post, I had the chassis running nicely with the controller wired directly to the motor, but picking up from the rails was less impressive, despite the fitting of the 'Simpson spring pickups' rubbing on all the axles. The chassis was disassembled and re-assembled a few times, to no avail, and another crank pin came loose from a wheel and had to be re-soldered back in. Quartering the wheels was trickier as the motor was now solidly in place, but plent
Still making progress, and still making mistakes. The etched chassis does not include any provision for mounting the motor, but I spoke with Jerry Clifford at the Didcot exhibition who said he fits a piece of plastic onto the centre frame spacer, files a curved saddle into it and glues the motor to that.
I always want to be a bit different, so I thought a blob of Milliput might form a saddle without the need for filing. My first attempt started well, but as the Milliput took a long t
Having produced a free running chassis at the end of the last session, I had to disassemble it in order to add the 'Simpson Spring Pickups'. These are pieces of fine phosphor bronze wire, acquired by straightening out some unwanted N gauge coupler springs. They are soldered at one end into holes in the chassis and pass behind each bearing so they will rub gently on the axles with the absolute minimum frictional force. The axle muffs need to be shortened to make room, and must have smooth ends so
More slow progress this week, and a sense of achievement. To put this into perspective, I have to admit that in the 25 years that I have been a member of the 2mm Scale Association, I have attempted to build a number of chassis for a variety of locomotives, using several different techniques, none of which were completed. I had at least 5 tries at making a chassis for an S15, using phosphor bronze strip for frames, as was recommended in those days. I just could not drill and ream holes without th
I have now received a new set of wheels of the correct diameter (8mm) and I have given them a quick spray of primer (one set black for my second Terrier and this set grey for painting green and black for my Southern livery Terrier).
The next job on the chassis was to drill out the 0.3mm holes for fitting the brakes and the 'Simpson Spring' axle pickup wipers. Two of the brake support holes require drilling into the side of a glass fibre PCB spacer. Typically, my drill bit
Not much progress to report on my Freshwater layout itself, as various projects have stalled for one reason or another. However, with some exhibition bookings a couple of months away, I had to make some progress somewhere. I turned to the fiddle yard.
Originally, in the rush to complete the layout for the 2mm Scale Association Golden Jubilee Challenge, I just roughly laid a few 60 foot track panels on double sided sticky tape across the fiddle yard and joined them up electrically. Th
As anyone who has seen my layout at exhibitions can tell you, so far some very unlikely motive power has been operating the Freshwater line of the Isle of Wight. I do intend to rectify this, but getting the layout operating smoothly, and scenery added were higher priority. I have acquired some Dapol A1X Terriers (one at least with the correct extended bunker) ready to be converted to 2mm finescale. Many months ago I started work on modifying the original chassis, as per an article in the 2mm Sca
With another exhibition looming (actually, tomorrow 9th May 2015 in Portsmouth) I felt I should do a bit more work on the layout. I had mostly been working on some more suitable motive power and rolling stock for the layout (none of which is finished yet). I had been making a few more trees in spare moments, including a large Elm tree that I am particularly proud of. These have now been planted, but lots more are still required, plus other ground cover.
When I moved to a new house, I purchased a shed to house all my model railway stuff. Initially all sorts of junk got stored in there, until I could not even get in the door. After 5 years, some of the junk was removed, and it was used to house some computer servers, poorly cats, spare furniture, etc. Finally, enough room was made to set up Freshwater to work on it (still no room for a chair though).
So, nine years later and the original paintwork was starting to look tired, so I fina
Freshwater will have more trees than any previous layout I have built, so I wanted to get some planted in time for the Farnham show (and 2mm Scale Association AGM). Previously I have used plastic tree armatures from Heki and Woodland Scenics. These start off as 2D trees, the branches of which need to be bent to produce a not very realistic 3D tree before attaching bits of foliage.
This time, I wanted to try new techniques. I had purchased a tree-making kit from Ceynix many years ago,
Following general scenic work completed in time for the Basingstoke exhibition, a start has been made on some detailing and buildings. One important detail item is the starting signal. Fortunately there is only the one proper signal on the layout, as it has taken 6 months to build it. The two ground signals required will be another story.
I wanted to build a typical SR rail-built upper quadrant signal, operational of course. I purchased some etched brass signal boards, counterweights
At the Basingstoke show, the only building on the layout was a Ratio SR concrete PW hut. There are only four other major buildings required to complete the layout, but all will need to be scratch built. I started trying to create drawings for the station building, using a 3D drawing package, but the more I did, the more I thought about 3D printing the building instead of using plasticard and printed paper as I had orginally intended. The complex decorative brickwork would be really difficult to
I love the sound of deadlines flying by. Having a deadline certainly provides a bit of impetus to get things done, even if not enough things actually get done in time.
When I accepted the invitation before Christmas, I had just about got all the electrical and mechanical gubbins beneath the layout working as required (see umpteen previous posts) and so, 4 years after the initial deadline for the 2mm Scale Association Golden Jubilee Expo in Oxford, I thought the time was right to star
If you have ever used hand held controllers to operate a layout, you will know that you need somewhere to put them when you need to deal with a derailment, or drink some tea. Often this means hanging it over the backscene, or letting it dangle down to the floor.
On previous layouts, I have used Velcro to allow the controller to be stuck at various places at the back of the layout. This is very handy, but removing the controller from the Velcro can cause some fairly major earthquakes
Freshwater station only has one platform, but it was extended at various times over the years. The first section by the buffers where the locomotive would stand is very low with plain brick facing. It then ramps up to a more normal height. The next section is typical Southern Railway concrete panels from the Exmouth Junction concrete works, while the latest extension used the Southern Railway lightweight concrete trestles, more standard components from Exmouth Junction.
Modelling the
It is over 12 months since my last posting on this blog. A quick recap of the project so far is in order.
Way back in July 2010, the 2mm Scale Association celebrated its Golden Jubilee with a special Expo in Oxford. Prior to this, a layout building challenge was issued for layouts up to 9.42 square feet to be exhibited at the Expo. I built Freshwater for this challenge. As a change from my normal use of relays to operate points, I decided to try servos for the new layout. I joined Merg to ge
It has been some time since my last post. During that time there have been various improvements, design changes, failures, successes and experiments on the electrics underneath the layout. I have still not quite finished, but I do have a working system again.
The original plan was to use Merg Servo4 kits to drive micro servos controlling points and permanent magnet uncouplers. A temporary switch box connected to the 25-way connector on the layout operated the individual points and un
In my last blog entry, I showed my recently completed Merg CAN-CMD CBus controlled DCC Command Station. The Merg kit includes the PCB and all the components to populate the PCB. For future layouts I will probably just mount the PCB directly to a baseboard and hard wire it in. However, this first one I wanted to keep as a portable and flexible unit.This meant fitting it into a case with suitable sockets, switches and Led indicators.
I found a suitable case on Ebay made from black plas
Not that sort of of bus - a layout control bus. DCC is really good for controlling trains, but is less suited for controlling points and signals and the like. A separate bus for operating accessories means that a short circuit on the track does not cause points and signals to change at random. The separate bus can also use systems that are more suited to train detection and route selection.
I initially joined Merg (Model Electronic Railway Group) in order to access their servo contro
A busy last few weeks in the run up to exhibiting the layout at the 2mm Scale Association Expo in Keighley saw the completion of the woodwork, and application of paint to protect it (and cover up my poor joinery skills).
Setting up on the Saturday morning I was pleased to find that I had not left any important bits at home, and everything fitted together as planned. Even though I did not clean any of the track, it ran really well, with just on sticky bit through one of the points to
As I have said before, woodworking is not my speciality, but I am building my own layout instead of helping build a club layout, so I have to do everything. Before advancing with scenic work, I really wanted a secure case or lid to protect the layout in transit or storage, and before the next exhibition, I wanted to have adequate lighting in place.I looked at what we had done previously, and what other exhibition layouts are using, and then decided to do something completely different. I decided
28 October 2010:
It must be the season for ballast laying. With all the track laid, wired up and painted, and a successful two days operation at the GJ Expo in Oxford I just needed an opportunity to have the layout set up for a few days to allow the ballast to be laid and for the glue to dry.
I followed the method used on previous layouts, applying the ballast dry, painstakingly moving around and removing it from sleepers and flangeways, then spraying water with a couple of drops of wash
18 July 2010: Following the Expo, I can now get on with adding the uncoupling magnets. I had always intended using permanent magnets, following their successful use on Brunswick. I bought some small magnets from Merg, but they were nowhere near powerful enough to operate the DG couplers from below the baseboard. Now I have purchased 50 'rare earth' magnets via Ebay. These are really powerful for their size (about 5mm diameter and 3mm long) and come with all sorts of warnings. 'Rare earth' magnet
6th June 2010: This week saw the completion of the track wiring, and the successful test running of trains all over the layout. Copper tape bus bars run beneath the tracks, and small 'dropper' wires link the rails to the tape (two per length of rail). There was just one missing link wire found. Wiring up the point operating servos is still to be done. From the photos you can see one Merg Servo4 board mounted under the baseboard. Two more of these will be fitted to control the remainder of t
