Jump to content
 
  • entries
    149
  • comments
    2,571
  • views
    224,411

Station Building Progress 4 (Getting by with a liitle help from my friends!)


wenlock

2,503 views

I've mentioned in previous posts in my blog, that although I was happy with the basic construction of the station building body shell, I wasn't sure how to best tackle the awning brackets or valance. William Clarke's station buildings have a distinctive valance style, which I wanted to capture in my model. The canopy brackets are also quite ornate, some of his designs had a monogram of the railway incorporated in them. The first thing I needed was a decent photo of the bracket style, ideally a good close up.

 

Thanks to this forum, Tim V sent me a link to photos that he'd taken of Brislington station. One of these is a great close up of one of the brackets

 

Brislington station awning bracket

blogentry-5869-0-31962500-1354709030_thumb.jpg

 

As you can see its quite a complex shape and I still couldn't decide on a good way of making one in 7mm scale, let alone the six that I needed for my station building!

 

Once again the forum came to my rescue! I was contacted by one of our members, crankpin who said he was willing to draw up the bracket in a CAD package and then use a laser cutter to fabricate the brackets from layers of card. I provided him with drawings and dimensions and this is what he came up with!

 

Card components laser cut to make bracket.

blogentry-5869-0-68154100-1354709544_thumb.jpg

These 5 layers are then laminated together using PVA glue to form each bracket. Once dry the bracket is trimmed to give the finished bracket shape.

blogentry-5869-0-38494300-1354709757_thumb.jpg

 

Once sprayed with primer its easier to see the fine detail and accuracy that crankpin has acheived.

blogentry-5869-0-45654900-1354709879_thumb.jpg

 

To say I'm pleased with the result would be a huge understatment! There's no way I could have made brackets using traditional methods to any where near this level of accuracy and consistency. That crankpin is a very clever chap! In addition to him making the components for the six brackets, he also drew up and cut from ABS sheet the required valance.

blogentry-5869-0-30199600-1354714045_thumb.jpg

 

Once again i would have found it impossible to capture the planking width and the square shaped holes as accurately as the laser cut has managed.

 

 

 

With the Valance and Bracket construction problems resolved, I felt inspired to make a start on the Awning.

On the prototype building, the awning was supported by six steel beams that ran right through the building and terminated on the rear wall. As the awning is nearly as big as the building that is attached, I decided to use a similar method to support my model version. Holes were cut in the front of the building and rectangular section brass tube was used to represent the beams. These were glued in position using epoxy resin.

blogentry-5869-0-10565800-1354714862_thumb.jpg

 

The awning was constructed using plastic card and the valance attached using Butanone, which appears to bond the ABS to the plastic card well.

blogentry-5869-0-98001200-1354715182_thumb.jpg

 

blogentry-5869-0-22731400-1354715210_thumb.jpg

 

blogentry-5869-0-89541800-1354715275_thumb.jpg

 

Well that's progress so far, I've still got to represent the ribing on the awning roof and make the gutters and downpipes. Once thats done I can start painting and adding all the little details, that will hopefully bring the building to life.

 

Thanks once again To Crankpin for all his skill and work on my project and to Tim V for his drawings and photographs of William Clarke buildings.

 

Until the next thrilling instalment!

 

Best wishes

 

Dave

  • Like 20

13 Comments


Recommended Comments

  • RMweb Gold

Pure William Clarke. Superb :-) And great to see what can be achieved when modellers collaborate and use modern methods. The glazing is pretty amazing too!

  • Like 2
Link to comment

Slight correction, the beams I saw supporting the canopy were wooden, never saw a steel one, I didn't see all the buildings.

 

Still, looking good, and those brackets are just so....

  • Like 1
Link to comment
  • RMweb Gold

Slight correction, the beams I saw supporting the canopy were wooden, never saw a steel one, I didn't see all the buildings.

 

Still, looking good, and those brackets are just so....

Hi Tim, thats interesting, I just assumed that they would need to be steel to support the weight of the canopy. Just goes to show, assume nothing, research everything!

 

Dave

Link to comment

I've put some pictures of the derelict Rowden Mill in my gallery, hoping they'd show how the canopy had sagged. Some buildings had wire supports going to the outer edge, I don't have a publishable picture I'm afraid. Picking up on the "steel" comment, the drawings of the Abbotsbury branch buildings show wooden canopy support.

 

Rowden Mill Close up

  • Like 3
Link to comment

Some later additions to his buildings such as the 1927 canopy extension in Kingsbridge use steel beams. You would be hard pressed to tell the difference even in 7mm unless you were upside down under the canopy, an unlikely viewing position I would think. Fantastic work again, the brackets and valencing are both exquisite and complement the top quality work on the main building perfectly.

  • Like 2
Link to comment
  • RMweb Gold

Thanks all, for the positive comments! The fact that members are willing to share their skill, time and knowledge to help projects along, are what makes this forum so worthwhile.

 

 

  • Like 2
Link to comment

Looking superb Dave!

Next time you want to know what brackets are made from,

just hang upside down under the canopy

and I'll get my camera :)

 

It does indeed demonstrate what a brilliant resource rmweb is

now, if only it could reduce the time I spend building a layout.....

  • Like 1
Link to comment
  • RMweb Gold

 

Next time you want to know what brackets are made from,

just hang upside down under the canopy

 

Sounds like a batty idea!

 

Dave

 

  • Like 1
Link to comment

Fantastic laser cut valence, Wenlock. What was the width and space dimension you adopted for each 'plank' ('tongue'?)

Link to comment
  • RMweb Gold

Fantastic laser cut valence, Wenlock. What was the width and space dimension you adopted for each 'plank' ('tongue'?)

Hi Miss P, I hadn't checked the blog for a couple of days, so missed your comment.

I'm glad you like the valance, I must admit "Crankpin" did a fantastic job and I'm delighted with it! The valance boards are 4.5mm wide with a gap of 0.5mm between each board.

 

Dave

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...