Jump to content
 
  • entries
    172
  • comments
    1,473
  • views
    376,504

All change – a north eastern perspective

Silver Sidelines

Entry posted by Silver Sidelines

2,063 views

 Share

Before continuing with my journey around the layout I thought I would share a few pictures of the Main Junction Station populated with some rolling stock that might have graced the north east of England in the 1960s.

11425533076_590b1f1797_b.jpg

Bachmann Mk1 Pullmans, Hornby L1 and Bachmann WD 2-8-0

The original theme of the layout is BR (LMR/WR) perhaps near Chester or there again maybe Shrewsbury or even somewhere further south. However I also have fond memories of growing up in north east England and with the availability of so many splendid ready to run models I have indulged in a few north eastern and Scottish types. Coincidentally the buildings for the Main Junction Station are those early Hornby Skaledale models based on Goathland on the North York Moors Railway. This was done purely for convenience until I can construct some more appropriate types. So some views with north eastern rolling stock should be a good fit.

11425442605_9afb4fca09_b.jpg

Bachmann V2 60964 suitably weighted and with blackened wheels

First a view of my very first Bachmann model, purchased from MG Models of Sheffield back in 1996 for what was then the immense sum of £62.95. I think it still looks a good model and can be relied upon to run well. This early model came with larger diameter carrying wheels beneath the cab rather than the undersize wheels fitted to some of the later Bachmann variants.

11425425725_5a479b0796_b.jpg

Another view of Bachmann V2 60964 after a trip around the reversing loop

In the 1960s the north east of England was still dominated by heavy industry, particularly the huge steel works that used to be Dorman Long on Teesside. The predominant inward rail traffic was iron ore, coking coal and in return steel fabrications and castings.

11425549043_dab5657fe2_b.jpg

Bachmann J39 with Bachmann Austerity 2-8-0

Lighter freight trains were handled by 0-6-0 J26 and J27 types. However as these types are not yet readily available a model of a J39, which were occasionally seen, will have to suffice. For heavier trains there were Q6s and WD 2-8-0s – so the Bachmann model is a good fit.

11425620883_ca6054412b_b.jpg

Bachmann A1 Kings Courier on express, note Hornby WD 0-6-0ST shunting

Express passenger trains on the East Coast Mainline were hauled by A1s, A2s and A4s with plenty of A3s in evidence on the lighter loads. The view above shows a Bachmann A1 passing a Hornby WD 0-6-0ST, another engine type used for short haul heavy goods trains in the Darlington Teesside area.

11425494944_def2375707_b.jpg

Bachmann A4 Dominion of Canada passing Hornby WD 0-6-0ST

No North Eastern experience would be complete without a view of a Gresley A4. Over the years I have owned a number of these models. With a bit of added lead they produce a model with a truly representative haulage power. Dominion of Canada was a recent purchase and I have to say that it was one of those models that was ‘nearly very good’. In hindsight I should probably have returned the model. The engine ran well and the bodywork was unmarked. However the more I studied the engine the more I realised that the front buffers were pointing skywards. Time had gone by and I couldn’t bring myself to return the model – so what about some hot water and some gentle manipulation?

11425318275_a38c61c0fa_b.jpg

Bachmann A4 bodyshell – disassembled?

I must have been lucky because with the influence of the hot water the ‘buffer assembly’ was readily detached. It was then a straightforward job to clean off the old glue and to reattach the buffer beam with the correct orientation.

11425494323_ea155e0ca8_b.jpg

Bachmann A4 William Whitelaw - chassis

I will just add two more views of Bachmann A4s. Well actually the chassis plus my additional lead weight.

11425367816_c26f3469b6_b.jpg

Bachmann A4 Dominion of Canada - chassis

When I first purchased William Whitelaw I was surprised that the motor was totally enclosed – might it over heat? Now with Dominion of Canada there is a gap in the chassis – is this an acknowledgement that there might be problems?

11425389034_be8b76d4b2_b.jpg

Bachmann J39 and Bachmann WD 2-8-0

A final shot of two freight trains to remind us of the industrial heritage that was the north east.

  • Like 6
 Share

10 Comments

Recommended Comments

Jon020

It's such a lovely looking layout and some grand stock there too... it must give you many hours of pleasure just watching the trains go by.

Jon

Link to comment
Silver Sidelines

Thank you Jon - yes I guess so. Unfortunately there are only so many hours in the day.

 

Regards Ray

PS I have been following your Lidl Display Cabinet posts with much interest - I have even got encouragement from the other half so to speak.  It is good to read your balanced and sensible comments.

Link to comment
  • RMweb Gold
Mikkel
  • RMweb Gold

Hi Ray, I'm enjoying this too. Apart from your very appealing layout I like the way you do the photos. Amazing what a difference it makes when the camera comes down to rail level height. The photos are very crisp and clear. I wonder what lighting you use for the photos?

Link to comment
Silver Sidelines

Hello Mikkel and Paul

 

Thank you both, I value your support and look forward Mikkel to your 'seal of approval'.

A layout to be truly proud of

....... I wonder what lighting you use for the photos?

 

The lighting for the layout is standard white fluorescent tubes (60w pairs). I used to use a Finepix camera but currently use a more fancy Sony model. Most pictures are taken using the 'A' setting (aperture priority) set to as high a number as possible. I think the Finepix would go to f11 the Sony only goes to f8. The 'secret' if any is to place the camera on a stable support, for example a station platform or a block of wood placed directly on the tracks. The Finepix was an older camera and I had to position the camera and then use the self timer to trigger the shutter to avoid camera shake. The Sony being newer has an 'optical stability mechanism' to minimise camera shake and I seem to be able to get satisfactory results simply by pressing the camera down against a stable report whilst at the same time triggering the shutter. Digital cameras are fantastic, enabling a range of shots so that only the best images need be saved.

 

Keep on 'looking in' and have a good Christmas both of you.

 

Regards

 

Ray

Link to comment
  • RMweb Gold
Mikkel
  • RMweb Gold

Thanks Ray. I have problems with depth of field, and I need more light. I keep putting off buying it though, but it's about time. Or here's an idea: I'll put "fluorescent tubes" at the top of my wish list. That should raise some eyebrows :-)

 

A happy christmas to you too!

Link to comment
Silver Sidelines

Hello Mikkel

..I'll put "fluorescent tubes" at the top of my wish list. That should raise some eyebrows :-)....

A new camera might go do down better? At low light levels my newest camera takes repeat multiple images - I am guessing to 'build' the necessary image. All very clever.

 

Regards

 

Ray

Link to comment
Richard Mawer

Ray, you continue to be an inspiration for me to continue. I hope one day to be able to run some trains in some of scenery. All feels a long way off at present. Your blogs keeps up the impetus. Thanks

 

Rich

Link to comment
Silver Sidelines

Great - I am not sure my wife would agree about the 'in some scenery' bit - there is a lot of brown paper and empty spaces that need attending to that don't get pictured!  Keep looking you never know.

 

Regards

 

Ray

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...