Jump to content
 
  • entries
    54
  • comments
    185
  • views
    41,322

Signal Success for Freshwater


Ian Morgan

1,253 views

Following general scenic work completed in time for the Basingstoke exhibition, a start has been made on some detailing and buildings. One important detail item is the starting signal. Fortunately there is only the one proper signal on the layout, as it has taken 6 months to build it. The two ground signals required will be another story.

 

I wanted to build a typical SR rail-built upper quadrant signal, operational of course. I purchased some etched brass signal boards, counterweights, brackets and ladders from MSE. The post would be scratch built, using bullhead rail from the 2mm Scale Association. I laid two longish lengths of rail together, and joined them with a blob of solder at each end. I could then drill through the pair for the joining bolts at the correct intervals, confident that they would line up later when the rails were parted. I found a piece of card of suitable thickness, and cut comb-like teeth into it. With some wire passed through the rail holes at each end, I could then sandwich the two rails either side of the card and solder the joining wires in each hole, with the card keeping the rails the correct distance apart. The comb slots in the card meant the resulting signal post could be slid off the card once complete.

 

I had some small surface mount gold-white LEDs, and decided to use one as the signal lamp. It is rectangular rather than cylindrical, but is about the right size. I formed a triangular bracket from some unused nickel-silver etch and soldered it to the signal post, and one end of the LED to the top of the bracket. This formed bothan electrical and a mechanical joint. Some very fine enamelled copper wire was soldered to the topmost terminal of the LED and runs down the post to the lampman's platform. The platform is actually a piece of thin double sided PCB. The lower face is soldered to the post with some more nickel-silver brackets. The top face is insulated from the post, and so the other end of the enamelled copper wire is soldered to it, as is the top end of the ladder. Electrical current for the LED therefore flows up the ladder, through the enamelled copper wire to the LED, and then down the signal post.

 

I used an old 4mm copper clad sleeper as a base for the signal, with the post passing through a hole drilled in the sleeper, and the lower end of the ladder through two smal holes. Both were soldered to the copper, again for both mechanical and electrical connection, the gap at the centre of the sleeper keeping them electrically separated.

 

A piece of nickel-silver was added to the top of the post for its cap, and some small backets from the MSE etch soldered to each side of a rail for the signal arm pivot wire to pass through. An MSE counterweight and bracket were made up and attached just below where the signal arm fits.

Dsc_7768s.jpg.e9652e0a0c5158a0ca20a69f30391ffb.jpg

 

 

 

Dsc_7769s.jpg.ac31a903e474f2ea0fcc77f03f87700b.jpg

A pivot wire was soldered to a signal arm from the etch, and the arm and post were painted, sprayed with white primer, and then brush painted black and colour details. Some red and blue-green paint was mixed in some Krystal Klear PVA which was then added to form the spectacle plates in the holes in the signal arm.

 

The final bit of above ground work was to add the operating wires. This is a very fiddly job, requiring good right-angle bends in the wire and a lot of luck.

 

Below ground, I created a lever arm from some more PCB, pivoting on a wire pin through the two rails. The lower end of the operating wire passes through a small hole in the PCB. A couple more pins were soldered into holes drilled in the PCB to act as mechanical end stops, so the signal operating wire cannot be pulled or pushed further than required and thus causing damage.

 

The signal was then carefully glued into a hole in the baseboard, with the base covered with ballast and ground cover. I will probably regret not making it removeable when cleaning the track, but I have not found an unobtrusive detachable mounting method yet.

Dsc04730s.jpg.dadd816190381439d7742abdbb8cab50.jpg

 

 

 

Dsc04737s.jpg.acb90364e1cbb4b730b15a0834671bdb.jpg

The final piece of the puzzle was the operating servo. One of the new design, 3D printed, Merg servo mounts was used, with the operating wire bent into a curious form to reach the lever arm below the signal. In the end, the operating movement was not as great as expected, and I could have got away with a smaller lever, but it works.

 

 

Dsc04740s.jpg.86dbff0e91f86711c76ccce38ebfe798.jpg

It is now configured into the Merg CBus system so that a single CBus event will raise the signal arm. This can be generated from a Merg CANCAB controller, or a simple push button on the control box I made to give simpler operation of the uncoupling magnets.

 

Any of the route setting events will lower the signal arm, so it should not be possible to forget returning the signal to danger before the next movement takes place.

Edited by Ian Morgan
re-loaded images

  • Like 12
  • Craftsmanship/clever 1

8 Comments


Recommended Comments

  • RMweb Gold

Very nice Ian. Looks quite fiddly to do but well worth it seeing the result.

Don

Link to comment

Ian,

Very nice.  I agree about setting the signal into the landscape (as yours is) - so often one sees a model signal on a plate and they just really shout "model!"

 

Ian

Link to comment

Hi Ian,

 

Nice job. Some fine soldering there.

 

I had some Westinghouse discs etched a couple of years ago because I'm not aware of any other source for these in 2mm. If you'd like a couple then let me know.

 

Regards, Andy

Link to comment
  • RMweb Premium

Andy, yes please, that would be great. Freshwater will be at the Aldershot show (and 2mm Scale Association AGM) in October. Could you let me have them there, or give them to somebody who is attending? I was just starting to look at ways of creating some.

Link to comment

Looks really nice, but...there may be one bit missing :-)

 

Most SR UQ arms had the UQ equivalent of the L&SWR LQ 'Annetts shield' in the form of a rectangular plate fixed to the face of the post immediately behind the green spectacle. Not obvious in photos unless the arm is 'off' and not every signal seems to have had one. Given that this would not have been a signal approached at speed, maybe it was omitted  -  any good photos of the actual prototype?

Link to comment
  • RMweb Premium

Here is the best photo I have found of the signal at Freshwater (an earlier one had a wooden post, but was replaced when the platform was extended). It also shows that it should be a lot shorter than what I built. Most signals on the island seem to be rather short for some reason. It could have the plate you describe. It is also not clear if it has a balance weight fitted. My excuse is that I only found this photo this year. Is it really 6 years since I made the model?

 

Freshwater_signal.jpg.59f9fa3a6b2315a87a0c7b64e28711d3.jpg

Edited by Ian Morgan
Link to comment

See my edited version of the photo attached.

 

The 'shield' plate is within the yellow box, it's possible to see through the gap between the rails and not see the spectacle, if you get what I mean :-)

 

There is (was) a weight lever, the back of it can be seen within the orange box. It was not unknown though for it to be omitted from signals that were very close to the signal-box, where the length of signal wire run was so short as to render it irrelevant. The Up Starting at Padstow was one such example.

Freshwater_signal.jpg.951601671900d0aeb6da33fbf286f4e5.jpg

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...