Jump to content
 
  • entries
    54
  • comments
    185
  • views
    41,391

Look out, its the copse

Ian Morgan

Entry posted by Ian Morgan in The Layout

954 views

 Share

Freshwater will have more trees than any previous layout I have built, so I wanted to get some planted in time for the Farnham show (and 2mm Scale Association AGM). Previously I have used plastic tree armatures from Heki and Woodland Scenics. These start off as 2D trees, the branches of which need to be bent to produce a not very realistic 3D tree before attaching bits of foliage.

 

This time, I wanted to try new techniques. I had purchased a tree-making kit from Ceynix many years ago, and I have collected some old mains leads to source copper wire for soldering together. I would build one tree using each technique and decide which I liked best.

 

The soldered copper method involves stripping mains cable (multi-core) and then twisting, bending and forming branches. The result is then soldered together, requiring a big iron, clips or pegs, or asbestos fingers. I got as far a the second branch before I gave up.

 

The Ceynix method uses short lengths of florist's wire (a fine stiff wire with green plastic coating) bundled together and bound with florist's green sticky tape. Branches are formed with two or three wires bound together. Branches are then gradually bundled together until a complete tree is formed. The tree then needs to be coated with air drying clay. This is a long slow process. I used a wooden tea stirrer and a pot of water to aid the procedure. When dry, the tree is painted, a quick spray of grey primer and then thin washes of grey-brown shades. The fine twigs and branches are represented by what is called folinet. This is a fine black jumble of synthetic fibres which has to be teased out before gluing in place. I have been told that this is no longer manufactured, so an alternative solution will have to be found soon. To finish off, a spray of aerosol mounting glue is followed by sprinkling with fine foliage.

 

I found this method much better, and liked the results, and managed to complete 12 trees in time for the show.

 

No matter what method is used to make trees, a good book of tree pictures is essential to produce realistic trees. Would anyone build and paint a loco, coach, or even a wagon, just from memory? Getting the general shape, density of branches and colour tones right really brings a tree to life.

 

The first photo shows a sycamore tree, with the taped bundles of florist's wire formed into branches. The last few millimeters of each branch is a single strand of the florist's wire without tape. The oak tree in the background is the real thing,

 

Dsc04762.jpg.b94aceb56b9d08751842d60523a216ba.jpg

 

The next photo shows the coating of air drying clay on a couple of smaller trees.

 

Dsc04764.jpg.d24d7b2c9c7b4735694a4d6e6bf7a125.jpg

 

And finally, the small copse of 12 trees planted on the layout. The sycamore is in the centre, with a coppiced silver birch to the left, and several small hazel bushes behind. Below the canopy of the main trees, some small alder saplings (single pieces of florist's wire with foliage added) are poking up through the ground cover.

 

 

 

DSC04795.JPG.4cf5b104f21c45943b03ea471aff5ae3.JPGDSC04790.JPG.7257c082016521900aacdd16bdfdb51a.JPGDSC04788.JPG.8ecd74fb8df6947691d6a075862fe270.JPGDSC04776.JPG.e11839acea44532da68a963c135d03c7.JPG

 

 

So, 12 trees do not go very far on a rural layout. I will be building trees for many weeks to come.

Edited by Ian Morgan
re-loading images

  • Like 5
 Share

8 Comments

Recommended Comments

  • RMweb Gold
gwrrob
  • RMweb Gold

Nice work Ian.I spent some money on a couple of trees off the Ceynix stand including an armature very much like yours which I'll add Heki foliage. Just the job.

Link to comment
  • RMweb Premium
KH1
  • RMweb Premium

Greenscene do something that would replace the clay which is just painted on. Mind you it does remind me of a slightly rubbery Artex so you could experiment with a bit of that and PVA or even decorators caulk and fine sand to give a bit more texture.

Link to comment
  • RMweb Premium
Ian Morgan
  • RMweb Premium

 

Mind you, you have to look hard to see the Alder saplings!

I think I can see some in the last photo, but I know they are there. Like the lamp on the signal, which is just about visible when I cup my hand over it. If it were bright enough to see, it would look wrong.

 

 

Greenscene do something that would replace the clay

I might look at other materials for the bark, but

Link to comment
  • RMweb Premium
Ian Morgan
  • RMweb Premium

Someone at the Farnham exhibition showed me some similar fibres he found in Hobbycraft. However, they come in shanks rather than the scrambled mesh that is folinet. Unfortunately, I cannot remeber what it was called, so cannot find it on their website. Scambling the shanks should not be too difficult.

Link to comment
  • RMweb Gold
Donw
  • RMweb Gold

The trees look good. I was sorry to miss you at Farnham just didn't have enough time the AGM seemed longer.

No pictures of how it was in railway days but there are a lot of trees along the old line these days. I have some pictures if you need them.

Don

Link to comment
  • RMweb Premium
Ian Morgan
  • RMweb Premium

The material I was told about is called batting, or wadding (depending on which side of the Atlantic you are). It is used in quilting. Eight pounds something bought me a 36"x48" sheet of black poly wadding. This is a thick, rug-like, material, but I cut a small piece from a corner and gently teased it out, and ended up with something similar to the original folinet. I reckon I have enough to make a small forest now.

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...