Jump to content
 
  • entries
    122
  • comments
    870
  • views
    104,176

A new 'Old Engine' - GWR 184 - part 8


MikeOxon

1,090 views

blog-0234049001421069326.jpgAfter completing the main structure of No.184, I have been adding a number of rather awkward parts, in order to complete the 'brasswork'. This is the last chance to show the model, before adulterating it with white metal and plastic components, and then seeing everything disappear under a coat of grey primer!

 

The fitting of these additional parts is difficult on a locomotiive with lots of flowing curves that are hard to measure accurately. My method has been to make paper templates, cut out by a process of 'trial and error'.

 

First off were the splasher tops, which I tucked under the footplate in front of and behind each wheel arch. Fitting these around the cab sides was particularly awkward but, once the paper parts had all been marked out, it was then easy to transfer the measurements to brass sheet.

 

I found that 'Cornwall Model Boats' supply assorted packs of thin brass sheet in 1, 2, 3,and 5 thou thicknesses. (their website is worth a look, as they have many items potentially useful for railway models) I used the thickest of these sheets (5 thou - 0.125 mm) for both splasher tops and footplating, while the others have been used for various small 'finishing' jobs,

 

blogentry-19820-0-02147800-1421069063.jpg

 

I was pleasantly surprised to see that very little 'filling' was needed between the splashers and the boiler - the gaps had looked much larger when the wheel arches were 'open'. At the same time, I didn't experience any problems with wheel clearances, so this part of the construction went very smoothly.

 

The next step was to add the curved footplating. I first filled the curves behind the cosmetic outside frames with 'Milliput' putty and then, once again, used paper strips, laid over the curves, onto which I marked the positions for cut outs, to accomodate the splasher fronts and cab sides. After transferring the pattern to 5 thou brass sheeting, and cutting it out with a scalpel, I used super glue to fix the sheets in position on each side of the engine. I started to lay the sheeting at the front end of the chassis, pressing it down firmly, to follow the curves over the driving axles, and ensuring a straight edge, overlapping the cosmetic outside frames.

 

blogentry-19820-0-25078100-1421069082.jpg

 

The join between the raised top of the firebox and the boiler was my final problem, which I wrestled with for some time! I first fitted boiler bands in front of and behind the area where the parts needed to be joined. I used jewellers' snips to make several short cuts into the leading edge of the firebox, where it is raised above the boiler, and then carefully folded these down to make the curved joining fillet. Finally, I cut a sliver of 1 thou brass shim to cover over the curved 'fingers' that I had made with the snips. It is not perfect but I hope that it will be adequate, one it has been painted. I added the other boiler bands, once the boiler and firebox had been joined together.

 

blogentry-19820-0-12967700-1421069135.jpg

 

In some places, the side frames, formed by folding the sides of the main platform, were deeper than the cosmetic outside frames. I found it helpful to make a series of snips along the excess depth before using a sanding drum on my mini-drill to trim off the excess (10 thou thickness) metal.

 

blogentry-19820-0-89529900-1421069172.jpg

 

So far, everything seems to fit and the chassis rolls freely, so here is a last look at the structure in its shiny brass finish:

blogentry-19820-0-88685000-1421069190.jpg

 

There's still quite a long way to go but I can now be confident that a 'rolling' model will be achieved :) In the first instance, I shall power it with my 2.500 gallon Dean tender but I have left plenty of space between the frames, with openings below the boiler, to accommodate a motor in due course.

 

Mike

 

Continue to next part

  • Like 5

4 Comments


Recommended Comments

  • RMweb Gold

Hi Mike. Some tricky bits there, but a very nice result. The good old trial and error approach has a lot going for it. In all aspects of life, I think!

 

Thanks for the link to Cornwall model boats, looks like one of those trading sites that will steal both time and money :-)

Link to comment

Thanks Mikkel.  I think you may find many items of interest for The Depot on the Cornwall site : plenty of barrels, boxes, bollards, capstans, etc.

 

I'm now searching for detailing parts - I know I've got some footplate-top springs somewhere - but where?  :)

 

Mike

Link to comment
  • RMweb Gold

Ah yes, I had almost forgotten about capstans, I need some of those.

 

The footplate top springs will have mysteriously vanished until you've bought some new ones, then they will turn up right in front of your nose.

Link to comment

I made the mistake of tidying my work room before the Christmas break so, of course, many things took their opportunity to 'vanish'. 

 

Some of these are now beginning to turn up - I found my fibreglass 'pen' today, so have been able to polish up the brass-work.  My curved scissors are still missing and there must be some packets of spare parts still in hiding.

 

I've just added the grease axle boxes for the leading wheels so it's only the springs now!

 

Mike

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...