Jump to content
 
  • entries
    93
  • comments
    685
  • views
    144,683

The Little House on The... (Part 3)


D869

1,679 views

The painfully slow progress of the 45xx build continues. The loco had a test run at AbRail where it showed a tendency to derail. After readjustment of the pony truck springs it had another run at Macclesfield and was much better behaved. Over the past few months I've been gradually making progress with putting the cylinders together and tonight the second one was finally fitted to the loco.

 

blogentry-9623-0-52386700-1429909256_thumb.jpg

 

I've got to say that they weren't the easiest of things to put together - annoying issues like the square holes to take the slidebars being too small. The crossheads come as a set of 3 loose bits that need to be held in alignment somehow during assembly and you need to provide the piston rods yourself (mine are made from some suitably thin bits of scrap etch). I didn't like the use of a single etch thickness for the motion brackets so I soldered some nickel silver wire along the outside edges which results in something that looks a bit more beefy. All of these little niggles are probably why I kept losing interest and finding other things to do.

 

The kit as it comes also has an issue with the alignment between the outside steam pipes and the cylinders - the steam pipes should be central to the cylinders but they are quite a way out. My answer to this was to take a large file and remove one millimetre or so from the front end of the chassis so that the whole thing can sit further forward. This improves the alignment of the steam pipes a lot and also puts the front pony wheel and front driver into what looks like a more prototypical alignment with the bits above the footplate. This change also needs the motion brackets to be moved back along the slidebars from the etched 'pips' provided but the new position seems more in keeping with drawings of the real thing. Another slight downside is that the rear pony truck is now a bit too far forward but that's not an unsolveable problem.

 

Anyway, the cylinders are at least tacked into place now and the chassis still runs properly so I can move on to the next jobs. I think the next task will be to sort out the body fixings (complicated by my having moved the chassis forward by 1mm so the holes no longer line up). The motion brackets might need some more work because at the moment there is a gap between them and the footplate but I'll wait and see what happens when the body is fixed down properly. I'm also intending to try brush painting two pack etch primer on the cylinders to try to make the paint stay put on these exposed bits of metal. The instructions say it can be done, so we'll see.

 

Another pic with the body removed...

 

blogentry-9623-0-40554500-1429909275_thumb.jpg

  • Like 12

4 Comments


Recommended Comments

  • RMweb Gold

Really starting to come together now Andy. It's a shame all these various issues with the chassis etch were not dealt with at the test build stage. I believe Chris Higgs is doing a prairie, or at least a 44xx.

 

Jerry

Link to comment

Thanks Jerry. I'm hopeful that the trickiest bits are done now. The only remaining loose bits from the etch are the brake shoes. I haven't yet decided what to do regarding brakes but I'm not massively keen on the idea of soldering more odd bits of wire onto an already painted and working chassis.
 
I think I'll want to do something other than a 45xx (or 44xx) for a good spell now, but thanks for the info about Chris's possible future plans.
 
It might be nice to get back to something more diesel hydraulic again given the title of this blog ;)
 
Regards, Andy

Link to comment

Don't get over excited about my 44XX. Given I am doing it for myself and probably will sell a handful to other people, I won't be going through multiple repetitions to get the design 100% smooth. If it can be built, that will be good enough for me. I will only re-etch parts if they really are unuseable.

 

I suggest you solder the brakes up separately onto the wire and then glue them to the chassis so the paintwork is untouched. Personally I don't like locos without brakes.

Link to comment

No worries Chris. I quite understand.

 

The brakes are fitted now. I decided that I had to do them or else I would never get around to it. I used Nigel Ashton's approach as inspiration so all six shoes are mounted onto a sub-assembly that fits up under the loco... with no soldering to the actual chassis required. It's taking a few liberties but at least I have brakes now.

 

Regards, Andy

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...