Jump to content
 
  • entries
    54
  • comments
    185
  • views
    41,316

A Terrier for Freshwater


Ian Morgan

1,143 views

As anyone who has seen my layout at exhibitions can tell you, so far some very unlikely motive power has been operating the Freshwater line of the Isle of Wight. I do intend to rectify this, but getting the layout operating smoothly, and scenery added were higher priority. I have acquired some Dapol A1X Terriers (one at least with the correct extended bunker) ready to be converted to 2mm finescale. Many months ago I started work on modifying the original chassis, as per an article in the 2mm Scale Association magazine. I even 3D printed some replacement gears incorporating axle muffs, to replace one of the originals that I ruined while reaming the centre hole. The hole had drifted off-centre. Just a couple of weeks ago, I had the chassis running, although its starting speed was about 40mph. I even got as far as connecting a small DCC decoder, and this actually improved it, with much better starting and stopping. However, electrical pickup was still a bit hit and miss.

 

Then, the long awaited replacement chassis etches appeared on the 2mm shop lists (3-661). A couple were ordered. There are no specific instructions for the Terrier chassis, just the generic build instructions, plus a couple of drawings hidden away in the 2mm VAG files area. After a couple of emails to Chris Higgs,I put together a parts list:

  • 6x crankpins and washers (3-107 & 3-109)
  • 1x 30:1 worm and gear (3-364)
  • 2x gear muffs (3-102b)
  • 2x axle muffs (3-100)
  • 1x 14 tooth M0.3 gear (3-390)
  • 1x 22 tooth M0.3 gear (3-394)
  • 6x 8mm driving wheel (3-005)
  • 8x frame bushes (3-113)
  • PCB strip (3-156)
  • Nigel Lawton 8mm dia x 16mm Midi Motor

The Terrier chassis etch has some differences from the other chassis etches:

  • There is no fold up gearbox for the worm assembly
  • There are frame reinforcers to be 'sweated' to the insides of the main frames to strengthen them.

So, for my first evening working on the chassis, I started by folding up and soldering the chassis building jig. With luck it will survive long enough to be used for the second chassis.

 

Then I started on the chassis frames. Unfortunately, the reinforcers are not arranged on the etch as a 'fold and align' arrangement like the coupling rods and bosses are, but need to be cut out separately before attaching to the main frames. Where the idler gear axle bush cutout is on the frame reinforcer, it dissects the top edge leaving a very thin piece of metal keeping the two ends of the reinforcer together, so must be handled with care. It might be possible to use some fine rod in the brake gear holes to align the reinforcer and the frame when soldering them together, but the rod would probably get soldered into the holes at the same time. I therefore aligned them by eye. Alignment needs to be accurate, or the frame bushes will not locate properly into the frames.after sweating them together, I inserted the frame bushes into their holes and soldered them in. The holes needed to be reamed a little to get them to fit. This requires a slightly larger reamer than found in the usual, cheap reamer sets.

 

The PCB tabs were then folded at right angles. The tabs with holes in, I folded along the wrong fold lines, so I will have to rectify this later. The frames were then fitted into the jig, and axle rod inserted. This completed the evening's work. Next time, the PCB spacers need to be added, then I can try it with wheels and gears, and add the coupling rods. Then I have to ponder fitting the motor and worm.

 

 

Edited by Ian Morgan
removed lost images

  • Like 10

5 Comments


Recommended Comments

I thought 4mm scale was hard enough.

 

Good luck hope it works well and will be watching with interest.

 

All the best Dan

Link to comment
  • RMweb Premium

I have heard from the etch designer, Chris Higgs, and he recommends fitting the bushes first, and then the reinforcers can be located around them, which should prove simpler.

Ian.

Link to comment
  • RMweb Gold

Hi Ian, I have just picked up one of these etches so I can add another Terrier to the North Somerset Light's roster.

I have used several of the Nigel Lawton 8mm motors in my. NSLR locos and the MR 1F on my Bath Queensquare thread also has one. Almost without exception I make up a simple sadly from plasticard, or filed into the PCB spacer depending on the amount of space available and glue the motor in with a spot of superglue. I tend to set the mesh up tight then glue a piece of paper or two to the motor to give a nice working clearance. If you need to take the motor out at some point in the future put a small screwdriver under one end and twist to break the joint.

I'll post a picture of one with the lid off if interested.

 

Jerry

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...