Jump to content

Shelf Island

  • entries
    80
  • comments
    184
  • views
    69,534

Sleeper-built coaling platform (Poppy's WoodTech)

47137

1,477 views

I spent some time admiring the timber kits by Poppy's WoodTech, weighing up the pros and cons of trying out an overscale 4 mm kit or an underscale 3 mm one. The coaling platform appealed in particular, it looked more realistic than something I could make from strips of wood or styrene. After a while, I wrote to them and asked if they could do a 3.5 mm (H0) version, and my kit arrived in the post about four weeks later.
blogentry-14389-0-84429900-1481058251.jpg

 

We had a brief correspondence along the way concerning the best size of the sleepers because this would follow on to any further kits for H0. In essence, there is no "true to scale" model railway track for British H0, so I suggested the scale size of a real sleeper. This ends up close to the size of sleepers in Peco track (which are essentially correct but too close together), and rather smaller than the sleepers of SMP type J (which are about the right pitch but too long and too wide):

 

Length: 29.8 ± 0.2 mm
Width: 3.0 ± 0.1 mm
Thickness 1.6 +0.2/-0.1 mm

 

These dimensions represent 1/87 of a real sleeper, which is usually 8' 6" long, 10" wide and 5 or 6" thick, with tolerances added by me to blend in with Peco and SMP. The ideal being to make a kit for a scale model which looks good with the track on the British H0 modeller's own layout.

 

I haven't built the 4 mm scale version of this kit (reviewed in the mainstream press) but the H0 kit looks much the same as the photographs I have seen. Inside the bag there are some pieces of laser-cut plywood and a sheet of instructions:
blogentry-14389-0-37071700-1481058252.jpg

 

The sections for the deck and the walls are to be glued up from two layers of 0.9 mm plywood, while the legs and braces underneath are a single thickness of 1.6 mm plywood. This means, the deck and walls end up a shade over scale thickness (about 1.9 mm total) while the legs and braces are spot-on. It all looks right to me - much more like real sleepers than the bases of flexi-track.
blogentry-14389-0-52118500-1481058254.jpg

 

The kit was a pleasure to built - all the parts are exactly the right size with virtually no filing or fitting. I chose to put walls on three edges of the platform and I trimmed these walls to the lengths I wanted but there is plenty of flexibility to choose your own arrangement here. There are ten little diagonal braces to go in underneath, these rely on simple butt joints but they were more of a fiddle than difficult. Looking at the photo below, I'm happy to see they all went in with a consistent pattern, and they are still there:
blogentry-14389-0-86615400-1481058252.jpg

 

The kit is entirely plywood and it includes the parts to make an access ladder - two runners with five treads. I had an off-cut of 'Plastruct' ladder to hand (probably their 1:100 scale) so I cheated and glued this on instead. I put the kit together with PVA, slightly diluted with isopropyl alcohol and water, and applied from a little dropper bottle from Metcalfe Models.
blogentry-14389-0-07176000-1481058255.jpg

 

So - we now have a new kit for a British H0 structure (probably the first one for some time), and it is from a British manufacturer. Furthermore, if you model in one of the less-popular scales, perhaps the GEM 1:55 narrow gauge, you might like to ask Poppy's WoodTech if they can help with a suitable kit. Their approach using laser-cutting of real wood must surely be a great help for planking and other timber fittings with a lot of repeated detail.

 

This is a super kit.

 

- Richard.

  • Like 5


4 Comments


Recommended Comments

That does look good, and nice to see a manufacturer responding so quickly to your request. Thanks for the info.

Share this comment


Link to comment

Proper job, well done buddy.

Thanks for this John. I imagined the occasional crane bucket slamming into the vertical panels from time to time, so I went for a chunky approach for their supports, with two supports side-by-side behind the right-hand end. Also this let me use up all the support sleepers in the kit.

 

I trimmed the right-hand panel short of the platform edge so it didn't make for a pinch point between a model worker and an engine.

 

- Richard.

Share this comment


Link to comment

The most exciting part of this for me is a custom manufacturer actually producing something from a request.

 

I model British OO but in Australia, I have added this supplier to my list as they obviously are enthusiasts too.

 

Thanks

  • Thanks 1

Share this comment


Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.