Jump to content
 
  • entries
    171
  • comments
    1,469
  • views
    376,240

Silver Sidelines

1,282 views


Coming from the North East of England I couldn’t let these new Hornby models pass me by.   Thane of Fife had already disappeared from my 1960 ABC books and I never got to see Cock o’ the North. There is a big red line through the number in my book, confirming its imminent withdrawal.  I did see the two A2/3s, Steady Aim being a York engine whilst around the beginning of the sixties Sun Castle was based at New England and then Doncaster.

 

 

51019492006_b5a597a25e_5k.jpg

Thane of Fife after some adjustment to sand boxes and running plate

 

50997401929_9e6b628359_5k.jpg

Steady Aim after some adjustment to the speedometer bracket

 

I hadn’t pre-ordered any of these Hornby models and was initially only interested in the two Late Crest engines.   The two Early Emblem engines were bought as an afterthought with some surprise earnings.

 

All the models I have handled have run very well.  With some notable exceptions the models are also very impressive.  This Post summarises various issues (and fixes) that I have come across with these models.  

 

I had to hunt around for Thane of Fife, my first purchase.  The seller, I will spare his name, had opened the box and checked the engine but it still arrived with its front lamp iron loose in the box along with another piece of plastic which I eventually identified as a handle from the front of the tender.  (There should have been two but one was completely missing.)  However the most serious problem in my eyes was the gap between the firebox and cab, the latter being attached at a rather jaunty angle.  The model was returned.

 

50998698264_e5a783f8b6_5k.jpg

Bits in the box –now which way round does the lamp iron go?

 

50998697949_d0d2c7818a_5k.jpg

Cab and firebox misaligned – model returned

 

Then there is what I will refer to as the elephant in the room, the shade of green and the red lining – why?  A difficult choice – do you use a coat of satin varnish to improve the green or will that also darken the red lining?

 

51083619606_9e64e2a0c4_5k.jpg

Bachmann lined green compared to Hornby lined green

 

Sun Castle was the second model to arrive from Hornby and this was received in better fettle than my first Thane of Fife which was replaced with a much better model from the same shipment as Sun Castle.  One or both of these models  needed the tender water scoop turning through 180 degrees, not a difficult job as they were poorly attached (if at all).

 

Hornby appear to have shipped Sun Castle (and subsequently Steady Aim) with only two sets of sand pipes.  The running plate on the A2/3s has three sand boxes and the wheel retainer (bottom plate) has mouldings to fit a third wire sand pipe – it just hasn’t been fitted. 

 

51093807167_60a63593fe_5k.jpg

Spot the space for the missing wire sand pipes at the right

 

51093791919_62c0d87aeb_5k.jpg

Sun Castle with three sand boxes and wavy reversing lever – it should lie tight up against the footplate (ignore the disconnected speedo I was inside adding lead).

 

Subsequently it has been pointed out to me that that the reversing lever on my picture of Sun Castle needs some adjustment so that it lies tight up against the footplate.

 

Returning to Thane of Fife I was not happy at the way the double sand box on the driver’s side stood proud of the running plate.  As with so many of the detail parts on the model it can be easily damaged if subject to too much manhandling.  I eventually added a fillet of black coloured Perfect Plastic Putty and gave both the putty and the sand box a coat of satin varnish – as shown in the picture at the top of this Post.

 

Steady Aim and Cock o’ the North were bought together and inspected prior to posting.  Both arrived with the front lamp iron loose in the box.  Cock o’ the North had also lost the rear buffer beam from the tender.  I am guessing that the ladies in China must have special tools to fit these tiny pieces.  It took me a long long time to refit the lamp irons.  For Cock o’ the North I used some matt varnish on a piece of wire, for Steady Aim the varnish didn’t hold and I resorted to using Super Glue, in both cases holding the lamp iron with Blu-Tack.  Now which way round does the lamp iron fit?

 

51069187021_d4e8833191_5k.jpg

Cock o’ the North - Top lamp iron reattached using matt varnish

 

51069279717_94ba28ae6e_5k.jpg

Top lamp iron reattached using Super Glue

 

What about the loose tender buffer beam.  There was little sign of any glue but then it didn’t seem to fit properly, in fact on inspection all the tender buffer beams seemed to droop downwards.

 

51082410187_8ac4557864_5k.jpg

Buffer beam droop

 

I enlarged the holes in the tender behind the buffer beam thinking that this would sort the problem.  It made an improvement but I think I must still be missing a trick with this issue.

 

51082409997_937adffbf0_5k.jpg

Enlarged holes behind the buffer beam

 

One of the cab doors on Cock o’ the North was hanging off at a jaunty angle.  It didn’t take much effort to remove the door, together with the driver’s seat which is all part of the same moulding.  There is a ‘peg’ at the bottom of the cab seat which fits into the cab floor, I would say a clever design but it does still need to be attached correctly.

 

50997393884_8b0d8b5264_5k.jpg

Cab door and driver’s seat moulding

 

Time to play trains!  Two issues suddenly appeared.  Firstly Sun Castle jumped the track at a set of points that have never been any bother before.  Secondly Steady Aim came to an abrupt halt when the tender derailed and the wheels shorted out the point blades.

 

I thought the problem with Steady Aim was simply that the water scoop was too low and had caught on point blades.  Removing the water scoop seemed to solve the issue but it soon became apparent that Steady Aim was a ‘lame duck’ in terms of haulage compared to the other models.  On further inspection I could see that one set of tender wheels was wedged at an angle by one of the phosphor bronze pickups.  On starting to dismantle the tender I realised that the brake rodding on one side was misaligned and that the bottom keeper plate was warped and would not lie flat.  Digging deeper I was able to see that the soldered connections to the pickups inside the tender had been made rather carelessly with the result that the solder had fused to the surrounding plastic forcing the phosphor bronze out of shape.  Luckily the solder was easily forced off the plastic and the pickups returned to the correct profile.  The moulding for the plastic wheel retainer and brake rodding was dumped into hot water and magically regained its original shape.

 

51009124655_adfbe427ec_5k.jpg

The warped brake rodding

 

51078405967_b4d90895a1_5k.jpg

Deformed phosphor bronze and the wedged wheel set

 

51078405652_51b621db67_5k.jpg

Soldered connections fused to the plastic surround

 

A good outcome but still none of these new engines would haul seven Bachmann coaches up my inclines (something that is not an issue for Hornby’s Britannias).  This brings me back to Sun Castle jumping the track.  With the engine on level track there is virtually no ‘up and down’ movement available at the front bogie – meaning that with the slightest unevenness in the track, or at a change in gradient the engine will be resting on the front bogie preventing it from easily moving from side to side and at the same time lifting the front driving wheels from the track reducing traction.  On closer examination it can be seen that Hornby have inserted a tapered spring between the bogie and chassis, there is no washer present.

 

51078527861_0843c6377b_5k.jpg

Bogie dismantled, showing the tapered spring – no washer

 

Clearances must be very tight and at times I think on my layout this spring is causing the driving wheels to lift off the track.  Bachmann had a similar issue with their Dukedog and City class models https://www.rmweb.co.uk/community/index.php?/blogs/entry/14484-Bachmann-gwr-4-4-0s-and-gradients/

 

With the springs removed I can imagine my models run more freely and they certainly don’t derail.  As to hauling seven Bachmann coaches for my layout I solved this issue by adding  15gm of lead – a circular disc in the end of the boiler and some lead shot in the screw holes in the chassis block.

 

51093725491_9951efb419_5k.jpg

Spot the lead disc

 

The seam along the top of the boiler on some of my models is rather uneven.  Whilst ‘inside’ the various body shells I suddenly realised that I could ‘see out’.  These models are very delicate and I would say that glue has been used rather too sparingly.

 

51078608681_f80d41eeb1_5k.jpg

Cock o’ the North – from the inside looking out

 

For completeness I have added some images of how I think things should be!  First the speedometer bracket that dropped off Steady Aim – it has to straddle the reversing lever.

 

51093820437_f8d5f0bb39_5k.jpg

Steady Aim – speedometer bracket

 

Some images of the reversing lever in I think its correct position, note the grooves in the footplate.  If the lever and valve gear are not aligned correctly and don’t sit in the grooves the footplate will be warped.

 

51094533695_3bf79bd6e2_5k.jpg

The reversing rod tucked up under the footplate

 

51093804404_1cf61c1e07_5k.jpg

Grooves on the underside of the footplate for the valve gear and reversing rod

 

There is a lot that is good about these models and they can be easily made to run very well.  The body shells are very detailed but very fragile and sadly from what I have seen they are not always glued together correctly.  Perhaps there are too many individual pieces to attach and not enough time allowed in the factory?  (The opposite problem to ‘Design Clever’ that produced Duke of Gloucester.)

 

The shade of green and the red lining used by Hornby doesn’t seem right but perhaps for a layout setting it becomes less important:-

 

 

Postscript

 

Since writing this Post I have been contacted by ‘Dominion’ of RMweb and encouraged to fettle Sun Castle’s reversing lever and to sort the drooping tender buffer beams.

 

51096411832_162a90cbd7_5k.jpg

 

The reversing lever seems to have been moulded or pressed from soft alloy.  It is easily pulled away from the body shell and can be gently massaged to the required shape.  It needs to tuck into the groove beneath the footplate.  I did wonder if the lever on my Sun Castle was too wide and I used a tiny screw driver to clean out the groove in the plastic footplate.  Having achieved the required shape and fit, the lever can be fixed in position with some tiny spots of Super Glue.

 

51096850639_08dfd70b25_5k.jpg

 

The tender buffers had been a work in progress.  In addition to opening out the holes behind the buffers ‘Dominion’ suggested using a triangular file inside the rebate below the top edge of the black plastic chassis.  I could imagine that there is a moulding line behind the top of the left hand buffer which by standing proud, was stopping the red plastic buffer beam from sitting correctly.  Certainly after careful use of a file I was able to push and glue the buffer beam back into a much better position.

 

Edited by Silver Sidelines

  • Like 8
  • Informative/Useful 5
  • Craftsmanship/clever 1

10 Comments


Recommended Comments

  • RMweb Premium

Thanks for taking the time to compile this detailed information, it will be really useful to quite a few I'm sure.

 

Syd

  • Like 1
  • Thanks 1
Link to comment

Excellent Ray, that's very useful. Your pictures do show how well detailed the models are, the valve gear and wheels especially. It's a pity that some models have had the assembly problems that you've showed.  Your blog shows a lot of potential problems to look out for.

Your pics of the locos are very good, you get a good depth of field, I'm experimenting with that at the moment. 

Also the video shows how well they run.

 

I've only got CoN so far, my one didn't have any problems (apart from top lamp iron missing) and it looks so good that it's had a lot of running since I got it!

 

Bill

Edited by railroadbill
  • Like 1
  • Agree 1
Link to comment

Thanks Bill.  I can understand why Cock o' the North has had lots of running - so quiet and so smooth.

 

Cock o' the North was one of Hornby's second batch.  Steady Aim was also the second batch.  Both seem to have been assembled better than the first batch.

 

Regards

 

Ray

 

  • Like 1
Link to comment
2 hours ago, railroadbill said:

.

Your pics of the locos are very good, you get a good depth of field, I'm experimenting with that at the moment. 

.

 Thanks Bill, I use a Sony DIgital Still Camera (DSC-HX350), quite expensive but probably a lot less money than a smart phone.  I take lots of pictures and throw lots away!

 

Regards

 

Ray

  • Like 1
Link to comment

Thanks for the camera info, Ray. I've got a couple of Panasonic Lumix cameras, one a bridge camera, one a compact, been playing with the settings to get the best depth of field.  Aperture priority mainly and setting aperture to smallest value.  Also tried my rather old Nikon dslr  where the aperture can go down to f32, but the newer cameras have the edge. One problem is the layout is in the loft and there is no natural lighting, so lighting is another experiment!

 

cheers

Bill

Link to comment
1 minute ago, railroadbill said:

Thanks for the camera info, Ray. I've got a couple of Panasonic Lumix cameras, one a bridge camera, one a compact, been playing with the settings to get the best depth of field.  Aperture priority mainly and setting aperture to smallest value.  Also tried my rather old Nikon dslr  where the aperture can go down to f32, but the newer cameras have the edge. One problem is the layout is in the loft and there is no natural lighting, so lighting is another experiment!

 

cheers

Bill

My Sony is I believe a 'bridge' camera with a Zeiss lens, the smallest aperture being f8.  I tend to use aperture priority.  The camera is quite compact and the trick is to find something to rest or press the camera against whilst taking the shot.  This way when you are using slow shutter speeds you can avoid camera shake.

 

Cheers Ray

  • Thanks 1
Link to comment
  • RMweb Gold

Looking at the sun-light through the top seam of the boiler, it looks to me like the sides of the boiler have not been held/clamped together for long enough for the glue to set properly - once parts have been added, the seam's been pulled apart, rather than it being a lack of glue.

 

As to fixing it, the easy option would be to put some low tack masking tape on the outside of the seam and squeegee in some Perfect Plastic Putty tinted to Hornby's Green (use Vallejo Model Air 71.324 Dark Green) into the gaps and let it set. 

 

The hard option requires clamping either side of the boiler (without damaging anything and applying some pressure). Then running some Tamiya Extra Thin (or equivalent hot glue) along the seam - just don't mask the outside. In theory the hot glue will soften the existing glue enough that pressure applied by the clamps will close the gap.

  • Like 1
Link to comment

Good Afternoon.

Has anybody had/found news of the LNER liveried A2/3s?

I have an 'Edward Thompson' on order and have not received any updates.

 

Could they be :-

Stuck in the Great Bitter Lake?

Delayed in arrival in European ports by the congestion around the Suez Canal

Diverted around Cape Agulhas?

 

Link to comment
4 hours ago, drmditch said:

Good Afternoon.

Has anybody had/found news of the LNER liveried A2/3s?

I...?

 

Sorry for the delay in responding!  I see on the 'Hornby' thread that Hornby have charged someone's credit card suggesting that their LNER model is on the way.

 

Thanks Ray

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...