Jump to content
 

CF MRC

RMweb Premium
  • Posts

    2,012
  • Joined

  • Last visited

Everything posted by CF MRC

  1. I couldn’t really resist continuing with the Westinghouse pump, so it now has the compressed air pipe fitted and the basic fittings for the steam feed and exhaust. The feed pipe fitting was made from some 0.5mm OD brass pipe, soldered into the groove cut in to the back of the steam cylinder. This did not have a large enough bore and so it was reamed out using an 06 endodontic file. These are the smallest used in root canal treatments and are made from nickel titanium alloy. The size represents 0.06mm diameter measured 1mm from the tip. The video clip shows it in action. The regulator on the LHS is next to be added and the pipe work can be seen here as a piece of 33swg phosphor bronze wire. Having this running plate unit as a separate sub-assembly has made it much easier to work on. Apologies if this post relives dental memories for some! Tim
  2. After a few hours of fiddling, the basics of the Westinghouse pump on 2400 are now complete. The steam supply & exhaust plumbing will probably be made later, the air delivery pipe rather sooner. A 2.3mm diameter blank for the cylinders was turned and centre drilled 0.4mm over 5mm depth. Drilling such a deep hole is taken very carefully, with many clearance removals, aided by RTD cutting fluid, and sharp TC drills. The blank was then finish turned with a graver, giving the raised ends to the cylinders. A piercing saw was used to separate the two cylinders, also making the stuffing box at each end. A conventional 0.4mm diameter steel drill shank was used to align the cylinders and a U shaped piece of brass (box section 1.6mm square with a side removed) inserted between the two cylinders - this represents the casting that holds them together on the real thing. The assembly was anointed with silver solder paste and pinned into a stable relationship with old drill shanks thrust into the charcoal block. The whole assembly was gently brought up to red heat for the solder to flash. On a very fine and small component such as this I turn off the workbench lighting so that I can gauge the temperature more easily. After pickling in citric acid, a few holes were drilled in the cylinders for the shuttle valve and oiler on the top, compressed air outlet pipe and a slot cut on the back for the steam inlet and exhaust pipes. The drill shank is a very useful handle to hold this rather titchy component. The mounting bracket on the running plate had been fitted previously (with two holes drilled in it) and this was augmented by a couple of pieces of brass wire which were threaded as one U shaped staple from behind and soldered in place. The excess wire was cut off and dressed in front and behind to neaten them up. These two pegs represent some substantial brass bolts in this area and made it easy to locate the pump for soldering to the bracket: the drill shank had previously been sliced off with a diamond disc. Having the main pump silver soldered ensured that it didn’t fall apart when attaching it to the locomotive. (photo courtesy Owen Chapman) The final result needs to fit very close to the boiler as the hand rail takes a detour round the top of it! The extra bits for the pump will be made when the associated plumbing is fitted. The piston is scarcely visible - like the real thing - but at least I know it’s there. The Association makes a 3DP version of this which is very fine, but I prefer turned metal in this situation. The 3D metal print looks a bit ‘hairy’. Quite crazy really, as the whole thing is only 6mm tall. Tim
  3. Some more progress on the Skittle Alley today. The representation of the prototype frames between the splashers have now been fitted. These were made by soldering a strip along the back of the splashers and then cutting out the unwanted bits with a piercing saw; finally tidying up with a bur, so saving fiddling with small pieces. The next item was the bracket for the Westinghouse pump. This was a very substantial casting in real life. The next photo is of a prototype made with a (too) small brass T section. The end piece is folded over and the junction with the upright pillar flooded with silver solder paste and gently heated to flash into the crack, so making a strong assembly. The definitive bracket was made from 3mm brass T section, filed down to size (approx. 2mm wide) with the foot silver soldered in place. A long handle was retained for holding during construction and positioning the bracket on the running plate whilst soldering: I use this technique a great deal for stabilising small pieces during assembly. The top had been partially cut through so that it simply needed twisting to remove the handle. I have a cunning plan for making the pump… Tim
  4. I have been working on the splashers for the Raven NER 4-6-2 class over the last few days. She’s beginning to look a bit more racey, with the wheels covered in a bit. The brass disc blanks were turned from a lump of brass in the Myford 254. The front face of the splashers, including the brass rim was finshed on this lathe as can be seen: Five discs were made and parted off. One as a prototype and two were used. The discs were mounted in a step collet on the watch maker’s lathe and hand finish-turned using a graver. Important to note that the graver is held with a pen like grip so that should it ‘catch’ then it flies from your grip, not through your hand. The thickness of the splashers was checked using a thickness gauge, which Jim will recognise. Once happy with the proportions the splashers were cut off as chord segments with a piercing saw. The tops of the running plates were made from 5thou steel, with suitable clearance notched for the wheels. The splashers were rebated at each end so as to locate on the steel when soldering into place. The engine has a Westinghouse pump on the RHS: that should be fun… Tim
  5. Nah… Go for broke, get those clouds in! Tim
  6. I had a really fun time at Ally Pally with the YR diorama last weekend. It was great to have visitors being able to get really close to the model to actually see it! The interest in underground modelling is clearly developing and I spent some considerable time showing individuals historical images and also construction images using the iPad. These have now been ordered into logical albums, which will also simplify giving talks. Tim
  7. I had a really fun time at Ally Pally with the YR diorama last weekend. It was great to have visitors being able to get really close to the model to actually see it! The interest in underground modelling is clearly developing and I spent some considerable time showing individuals historical images and also construction images using the iPad. These have now been ordered into logical albums, which will also simplify giving talks. Back to the Skittle Alley. Tim
  8. I was fortunate to get a picture of the paint sample ‘38 stock, looking very sharp and smart. Evidently, the non-motor cars are going to have some extra weight incorporated to improve running. I think these are going to be immensely popular - there is a tremendous amount of interest in the underground, as I found out this weekend at AP. Tim
  9. York Road all set up on the MRC stand 47. Lovely view of the rose window. Tim
  10. One of the Grove’s locos had obviously sustained a fall and had a badly mangled chimney. This has been screwed on to the smokebox and had a made-up saddle, with a filet of solder around the base. The brass chimney did, however contact the smokebox. Fortunately, it was easily removed from the loco and a brass dowel plug turned to fit from the base up to half the height of the chimney: it was then Loctited in place. The chimney top was then parted off from the base, but retaining the plug. I often use a piercing saw blade for parting off, these days. It is very precise, and makes very little kerf. A replacement top section was then turned up with a central hole to fit the plug. A graver was used for fine turning. This was then parted off and offered up to the base. Once Loctited in place, the chimney was finish-turned to the same dimensions as the original. The chimney was chemically blacked, Araldited in position and painted satin black to match the rest of the engine, Quite a long winded description of a fairly challenging little job. Should be ready for Ally Pally on Saturday. Tim
  11. York Road diorama will be in attendance on the MRC stand (not listed in layouts). Also flying the 2mm Finescale flag will be the Rydes Vale goods yard and engine shed, again on the MRC demonstration stand. This is the original 2mm fine scale layout from the mid 1960s. It is the first time it will have been seen in public for many years. Tim
  12. Maybe ‘trade’ has been good Jim so she’s gone for gold… Tim
  13. Vulcanite with porcelain gnashers. Tim
  14. They are exceedingly long. Take a look at the turnout that starts under Silver Fox. Tim
  15. As can be seen in this YR photo the bench along the platform has a lady sitting on it. The bench was made a few weeks ago from modified Shire Scenes etches. I thought that the lady would best be served by this figure from Modelu : On arrival I was most impressed with the quality of the printing, especially the magazine. Unfortunately, once all the supports were removed I found that the lady had a rather extensive protuberance below her derrière. Trimming this away wrote off the magazine and, I’m afraid, the poor girl’s right arm. Even then she would not fit on the bench that I’d made with her coy Princess Diana posture, and would look more like a child perching on the edge of a wall. Serious surgery was therefore contemplated. Those of a squeamish disposition should look away now. She was electively fractured just below the knees and placed on a thick sticky tape operating table for distraction therapy. As this was judged to be about the correct length, a small amount of light cured adhesive was introduced into the fracture site and polymerised. After checking her against the bench the void was made up with more light curling resin added with a pin in small increments. During the same operation, a new light cured prosthetic right arm was made. After a rapid recovery and following a bit more minor plastic surgery the lady was sprayed dark brown as a base colour and then painted with suitable acrylic wash colours. She is now reading the Daily Sketch, marvelling at the Flying Scotsman’s non-stop run to Edinburgh. Her newspaper was made from cigarette paper and held in place with varnish. The end result is one step closer to reproducing the B&W York Road photograph and, unlike many figures on model railways, she is sitting properly on the bench with her feet daintily touching the ground. For all that I think I must be mad to have spent virtually a whole day working on this figure. Tim
  16. I haven’t posted on WW for a while, but at least I have been doing a bit of 4mm scale modelling for the MRC’s new EM docklands lauout, ‘Orchard Wharf’. With modern ‘in-house’ laser cutting technology and 3DP components from Modelu, it is quite remarkably easy to make bespoke kit type buildings, which previously would have been a major effort. Do not fear though, I have stayed true to the faith and continued work on York Road tube station (2mm of course). The model is awaiting a pile of sand. It will be good to have the youngsters driving the tube train at Ally Pally, where this will be on display in diorama form. Having cleared the workbench of 4mm office blocks, I will be able to return to the Skittle Alley hopefully in time for Missenden Abbey next weekend. Tim
  17. After some careful internet image acquisition & editing, York Road now has a full set of 1920s posters. A pile of fine ballast, bench, fire cabinet and buckets are still needed to replicate the prototype photo. The images needed quite a bit of cleaning up and brightening before copying & pasting into the PowerPoint file. This software has a useful re-sizing capability and allowed mixing & matching of the posters for variety. The images were loaded onto a dark grey background and then printed at high resolution using an inkjet printer. The original PDF retains much of the resolution of the individual images which are degraded in the photo image. Commercial posters do not generally include the ‘local’ advertisements which are very characteristic of an area. The edges of the poster boards were touched in with a black pen. The posters certainly add a splash of colour to the model and help with the atmosphere. Tim
  18. York Road now has its ‘modern’ signage and electrical conduits. It will be on display in diorama form at Ally Pally (16-17th March) on The Model Railway Club stand. The signs were printed (Ben Weiner made the artwork) and the edge mouldings on the name board were built up with paint. The signs were thinned down at the back by careful scraping with a #15 scalpel blade to make them less bulky. The conduits were laser cut as etched strips, by John Jesson, sprayed with white primer then given a wash of stone water-based colour. The station now needs loads of advertising signs, a couple of benches installing, a Nestle chocolate machine and fire buckets with a hose cabinet. Tim
  19. CF MRC

    MRJ 301

    There are some super buildings and techniques in this current issue but, with few exceptions, they all have no evidence of this being a wet country (especially up north). The background building colours are spot-on and subtly weathered, but there is no evidence of mosses or lichens on any roofs or spreading up from ground level to the lower parts of the walls. I always use a dark green acrylic based wash on my buildings directed to where they will be damp or holding water. When applied at ground level it makes a structure look as if it is really planted. Perhaps I need to write an article… Tim
  20. Not on the N gauge one they didn’t! It had a planked running plate and was nearly TT in width. Tim
  21. The central trap door on the Sir Sagramore ashpan now has a control / locking device. It’s a bit unorthodox but it will hold the trap door shut when running. The linkages ended up with a rod pointing backwards at 45deg from the base of the footplate, with it pulled up to close the trap door. I therefore made a steel toggle that holds the rod in the open position: It rotates 90deg. and pushes in towards the backhead to open the trap door for ash disposal: I wasn’t convinced by the appearance of the toggle and it was also a bit slippery to handle. I therefore made a hand wheel to make it easier to hold and also reduced the locking pillar in size. The wheel was turned as a blank and mounted on a mandrel, Loctited in place. This was then drilled on the rotary table. The outer ring was then turned off to give the ‘grippy’ outer part of the hand wheel. After rounding off the edges the front face was given a rebate using a graver. The locking toggle components can be seen here, before assembly. The hand wheel was simply soft soldered onto the steel toggle, and held in place with a 10BA nut, with it pivoting freely on the rod - a piece of coat hanger suitably turned down & threaded. Finally an exciting video showing it in action! Back to small scale stuff now. Tim
  22. The problem is that the holes for the handrail stanchions are in the wrong place: there wouldn’t be an overwhelming case to replace these wire handrails …..with wire. The nearest thing to prototype would be a separate etch to represent the stanchions and the handrail with the holes in the correct position. However, as they are painted anyway, I think the moulding is a good bet. Each to their own tho’… Tim
  23. The art of small scale modelling is what you leave out, not what you put in. The moulded handrails will be far more subtle and if someone wants separate handrails then they could scrape them off and intall their interpretation of the prototype. Tim
  24. It really doesn’t matter what the difference is in the trackwork between 2mm FS and N gauge, it’s the overall ambience of a layout that matters. However, when Keith Armes made the mainline crossovers from a scaled up prototype track plan, he remarked that they were the longest turnouts he had ever made. They could not work with N gauge standards. Tim
×
×
  • Create New...