Jump to content
 

jazz

Members
  • Posts

    3,280
  • Joined

  • Last visited

Everything posted by jazz

  1. I'm afraid I do not have the instructions. I always send the instructions back to the guy I'm building them for. I rarely build locos for myself these days, I've run out of space for them now.
  2. Steve Fay is right on the mark there.
  3. That's the loco almost done and ready for priming. The tender will need sorting out next.
  4. I've been tackling a Javelin Collet Goods. This has been started and abandoned and I'm sorting it out to get it finished. (It's the tender that was part built but I'm Building the loco first this time. The dummy inside valve gear leaves almost no space for pickups so I'm going to devise some for the tender that will allow quick coupling and uncoupling.
  5. That's the Yorkshire Engine Co. loco built and ready for delivery. It did not turn out not as easy as I anticipated. Thankfully my scrap box came to the rescue a few times.
  6. Check the wheel is sitting fully up to the shoulder on the axle end. It does not take much to make the wheel wobble. (The larger the wheel, the bigger the wobble)
  7. Hi John. That is often a problem creating clearances on the leading drivers when the crossheads hit the coupling rod bushes. I leave the 2nd & 3rd axle bushes alone on the 45xx except for filing the bushes down to a tad over the thickness of the rods. The leading axle bushes are different. Decide just how much clearance is required. Sometimes I need to reduce the thickness of the coupling rods at the leading wheels. Also if still more clearance is required I turn the coupling rod bush round and place the washer on first then the coupling rod followed by the the bush and carefully solder it on. (Make sure the wheels centre boss will clear the coupling rod before you solder the bush in place.) That works for me. This photo is of the model I am doing that to now. Sorry it's a bit hazy, the close up setting was turned off.
  8. That's the build competed. Tomorrow will be the big cleaning up of it and preparing for the primer. I will have look at the water filler, it's not sitting quite right. the problem is the base is meant for a flat top to a side tank not the curved top on a saddle tank. Of course I have to add the buffers as well. I had to raid my scrap boxes to replace missing parts including the actual roof.
  9. Another day on the Mercian 0-4-0 build . Scratch building the s/box saddle was todays challenge, got there in the end. Over the hill now now and on the final straight
  10. First off, this was a second hand kit from GOG stand at Bingley Hall. So there was some items missing, most importantly the cast s/box saddle. There was some missing delicate etches. You have to watch the spacing on the chassis spacers as there is no etched lip on them for correct positions. My advice is to use the drawing in the kit to drill brake operating holes. If you have the drawing alongside you on the build and check it all as you go you should not have a lot of problems that I found. This was an original Mercian kit, it looks like they are under a new ownership and probably been reworked ??
  11. I've done very little of late, which had been unavoidable, but a star has been made on the Mercian Yorkshire Engine 0-4-0 loco. I started the new batch of builds with what I thought would be a nice simple kit. That has happened, it's quite a tricky build. The etches do not match up with the drawings needing a few alterations. Oh well, onwards and forwards.
  12. Finally got the Cardean 903 Class decided on and now all ready for the off. Not been the easiest of builds.
  13. At last I have the Royal Scott ready for delivery. It's been a bit of a slow build with a few other things going on around the house, but that's almost done now. I attached a hidden support bracket to the air pump which looked a bit iffy under the slide bar. (I think I will have to adjust the s/box lamp iron.)😕
  14. Excellent weathering. Well done. ( Jazz)
  15. Having been away from the WB for a while here is the Royal Scott "Jenny Lind" chassis. I'm going to start the body now before stripping the chassis down in preparation of painting and completing it. I have to decide the best way to attach the air pump to the crosshead and slide bar though. The slide bar being the trickiest job. Amazing how grubby the wheels become when left on the bench for a few days.
  16. The Royal Scott tender is ready for cleaning and priming. No issues with this assembly. I enjoyed this build after a few dodgy ones. So it's now go ahead with the actual loco build.
  17. Thanks, I have downloaded those instructions, they make sense where the original ones didn't.
  18. Got the bullion van ready for delivery now. Next up is a David Andrews Royal Scott. That should be a doddle as I've build quite a few of those under the Gladiator brand.
  19. Another van, this is the Ragstone Models bullion van. Not very good instructions provided on the one regarding the braking system. So I improvised on them.
  20. The horsebox is now ready for Geoff. All the very flimsy hinges etc were a bit of challenge. Not to mention all the handrails to be made from wire rod. (Getting them to be identical was the fiddly part)
  21. A little change here building the Roxey Moulding kit for the LBSCR horsebox. No brake gear provided except for the brake hangers and shoes.
  22. Thanks for all the above replies. (I have no books on the Caledonian Railway.) So that's all very helpful.
  23. No sure about that. Doesn't explain why only one front lamp iron.😉
  24. Cracking on bit with the Cardean loco. What I'm finding a bit odd with this particular prototype is there are no photos of in service with no lamp irons on the footplate, just the one in front of the chimney. Also no vac pipes on the front.
  25. Christmas greetings to you. And a very prosperous new year too.
×
×
  • Create New...