TexChem
Members-
Posts
51 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Events
Exhibition Layout Details
Store
Everything posted by TexChem
-
Vaguely recall there being a hoover on Burton shed around the time of its closure. My dad worked at the local newspaper and brought me a picture home - I guess there was an article in the paper at the time. You can make up a story to justify about anything.
-
Thanks - appreciate it. Getting ready to do the same on my own.
-
Looking good. What have you used for the hardstanding and how have you secured it?
-
Do you use a guide to maintain the angle of the cut?
-
Thanks for the tip - I am a chemist, so I use eye protection by second nature/
-
Great idea - but unfortunately, too late. Will keep in mind for the next time.
-
I have reached the point in track laying where I need to cut the track across baseboard joints - secured to copper clad. I have a Dremel and have used the standard disk which is supplied by Dremel. While it works well, the gap left behind is larger than I would like. Accordingly, I am looking for suggestions on where to source thinner disks or alternative methods to cut the rail. Appreciate your collective wisdom. Tex
-
Don't have a 20 p coin - what about US currency? Actually, I might have one somewhere.
-
I appreciate the continued comments and helpful information and I will, when the time comes, make a call about the "timber" widths to get something more appropriate. Had a water leak this past w/e, so no modelling - we have a holiday this Monday, I am going to try out the suggestion of using the short model switch and see how it turns out. I did not mention that I had widened the gauge to 16.5 mm at the ends of each of the switches to connect with regular track. I will not do that the next time and see how things go. Tex
-
I appreciate all the encouragement and feedback. These are just my first attempts and I am unlikely to use these on my layout - I am learning how to fabricate the parts, put them together and wire them up. Mike/Martin - appreciate the tips, time permitting will have a go this weekend. Dave - I purchased the copper clad from Clover House (I am in the US and this is US-based company), they are 3 mm, I believe, and so they are narrow. While I am in the learning phase, I am not overly concerned about this, but when it comes time to do them for use, then I will have to worry about it then. Tex
-
I decided two or three years ago to have an attempt at building my own turnouts - bought gauges, copper clad and some BH rail. Then, like many on here, life intervenes, confidence fluctuates, motivation ebbs and flows - nothing happened. This Christmas I took some time off work, closed all of my work related software (specifically email) and spent quality time with my family, which included some modelling time. As part of this modelling time, I pulled out the gauges, rail and copper clad and had a go. I made two B6 turnouts (using standard templot templates - no messing around, just set to 00-SF) - here they are. I have not yet gapped them, tried them electrically or put in tie bars - but they seem to operate ok when I had push through a short wheel base wagon. The curved turnout may need a little fettling in the diverging road, but I was quite pleased with them for my first attempts. I have to say it is really addictive and I want to replace all the turnouts on my layout - not sure I am ready to do it, but.........
-
Sourcing components ladders for fuel tanks at a depot
TexChem replied to TexChem's topic in Scenery, Structures & Transport
Thanks for all of the suggestions - these are exactly the types of ideas that I am looking for. Happy New Year All -
Sourcing components ladders for fuel tanks at a depot
TexChem replied to TexChem's topic in Scenery, Structures & Transport
Thanks for the additional suggestions. At least I won't have to look too hard for a supplier for swear words...... -
Sourcing components ladders for fuel tanks at a depot
TexChem replied to TexChem's topic in Scenery, Structures & Transport
All, Thanks so much for your valuable suggestions; given me lots of food for thought. Tex -
I am seeking the wisdom of the collective in identifying approaches to constructing access ladders (and safety barriers) that are found in fuel storage areas in TMD's. I am at a fairly advanced state of building a representation of the fuel tanks/pump buildings at the former Buxton TMD. The basic construction has been completed and I am in the process of adding the details, specifically at this point the access ladders (and safety barriers) - I am a bit stumped on how to progress. Any suggestions would be gratefully appreciated. Either components (etched or plastic) or from scratch are on the table. What I am trying to produce: https://www.flickr.com/photos/httpwwwpeakdaleworkscom/7700426500 What I have so far. Thanks a bunch.
-
Buxton was another
-
I too have been exceedingly happy with their customer service. Ordered some pre-owned wagons - a three pack and only one of the three turned up in Texas. Called and spoke with very nice gentlemen who investigated and found the other two wagons still in the sleeve in the storage bin. Apologized and sent the remaining two wagons which were received a few days later. I have been ordering from this store for longer than I care to remember and this was the first time there was an error and it was handled with class. Job well done.
-
Removing body from chassis - Hornby VDA
TexChem replied to TexChem's topic in Modelling Questions, Help and Tips
Mark + JDW - thanks so much. I will check them out tonight when I get home. I know that they are far from perfect renditions, hence why I plan to use them to hone various skills. Tex -
Removing body from chassis - Hornby VDA
TexChem posted a topic in Modelling Questions, Help and Tips
Over the years I have picked up several of these vans on ebay in various states of (dis)repair and plan on improving them - a means to learn some skills. As part of this general process, I need to strip the paint off two of these vans as the prior owner repainted them and I would like to separate the bodies from the chassis to facilitate the process; I do not see how to do this. Rather than force the issue, I thought that I would appeal to the general audience out here and solicit your help. Any advice would be gratefully received. Also, I am based in the US and I do not have ready access to "authentic paints", i.e., railfreight brown - any suggestions for alternatives in the Tamiya range? Thanks, Tex -
NEED HELP WITH FINDING STUFF
TexChem replied to DoctorP's topic in Modelling Questions, Help and Tips
You can probably figure out where I am located. I have found that as noted above many of the UK-based model shops ship quickly and accurately to the US; the VAT saving typically offsets the postage costs. Depending on the $ to pound exchange rate, the costs are really quite affordable. US-based British outline items can be found on ebay from time to time, including some kits, I have obtained several things by this route. And, if you're prepared to undertake some kit bashing, a good number of the US-outline kits can be Anglicized, particularly the industrial ones (I realize this is not what the OP is after). This forum is excellent and while views sometimes differ, there is nearly always a solution to a problem that you can use. -
Thanks for the tip-off here - bought some wagons that were at decent prices, coupled with no vat made for a very satisfying experience.
-
Waverley West, Princes St Gardens and Haymarket MPD
TexChem replied to Waverley West's topic in Layout topics
I have never seen this before, but it is so, so true. What are the second and third laws? -
Lineside Industries
TexChem replied to Narrow Gauge Jordan's topic in Modelling Questions, Help and Tips
Car (and other vehicle) manufacturing facility Oil refinery (other chemicals) Compressed gases Permanent way manufacturing Building supplies - thinking concrete support beams etc. -
Things which annoy you with modelling
TexChem replied to MJI's topic in Modelling Questions, Help and Tips
Finishing laying all the track, wiring it (successfully), ballasting it, installing point motors, painting/weathering track and thinking about installing scenery and coming to the conclusion that your skills have now improved such that you could do what you have already done so much better leading to being dissatisfied and a loss of mojo! Presently trying to decide whether to rip up what I have done, recover components and start again with hand built turnouts.......