Jump to content
 

innocentman

RMweb Gold
  • Posts

    182
  • Joined

  • Last visited

Everything posted by innocentman

  1. That looks like a DS10 to me. Fitted many into bogie trams over the years.
  2. Agreed As novice table saw operator I wouldn’t have the skills and probably the fingers after attempting angles!
  3. Been out in the garage today, taking advantage of the nice weather. Time to tackle the wiring on the mine boards. First up was the end board. Top of the board looks like this. After a couple of hours, the the underside was completed and looked like Only one point on this board. The MTB MP10 point motor and frog juicer are the only active components and are cabled directly to the cross board D connector using 8 core security cable. There are two spare cores which will be used to supply 12v DC to the board for a few lights on the mine building. Moving onto the next board, it was only when I turned it over that I realised we hadn’t put any cross braces on as I wasn’t sure of the exact positions of the point motors at the time the board was built. Out with the table saw and band saw and a couple of cross braces installed. And finally the wiring can commence. I got as far as fitting the frog juicers, point motors, DCC power bus connector, the link to the boards either side and finally the connectors for the control panel. Hopefully another four hours work through the week or next weekend will see the wiring complete. Until next time, all the best Andy
  4. A few post earlier you will recall the epic trans atlantic adventure of something I ordered from the USA. That particular parcel covered 13.135 miles and three trips across the Atlantic. I ordered something else from the a same supplier last november thinking it couldn't happen again! Well USPS have gone one better! This time an estimated 21,395 miles an not once over the Atlantic! I wouldn't mind if it was continuous journey but the parcel took a holiday from the December 11th 2023 to 23rd February 2024 in Sydney, Australia. After engaging with the Vendor who raised an exception with USPS the parcel finally arrived on the 28th February wearing a little label from Australia post confirming its mis direction and the raising of a case in the computer system. On the shipping label it was proudly boasting that it was shipped "Priority International US Postage Paid" I think I will try and avoid USPS in the future. All the best Andy
  5. Hi Ian, Yes I use a slitting disc in a battery mini drill to cut the rails. You can see it on the baseboards in the pictures above. I use a fresh large slitting disc that hasn't been worn down yet to keep any arc effect to a minimum. I do also possess a flexible drive which I could use to negate the are effect totally but I find the large disc works well. While slitting discs can be delicate, I tend to find that breakage mostly occurs when you abuse the disc or apply a lateral force unintentionally to the sides of the disc. In Page 2 back on 27th August, I posted a detailed set of images of the process I use for the rail joints, although I skipped over the use of a slitting disc by showing the end result. Regards Andy
  6. Evening all, The weather has improved and I have been back out in the garage and laid all the mine track this weekend. I have prepped all the baseboard joints ready for soldering the rails to the copper clad sleepers. I will try and get them soldered up, gapped and cut one evening this week. I couldn’t resist getting a planned full rake of 15 coal hoppers out and placed in the loop. Once I have cut the track across the joints, next job will be to take the boards down and get them wired up. All the best, Andy
  7. Really nice Les. Thats some 3D design to have all those textures. Can I ask what method you have used to print the building. Is it FDM or Resin? Regards Andy
  8. Not rude at all. If I had not already constructed the panel and superglued all the LEDs in place I may well have done that in the first place. I may 3D print a frame to tidy it up a bit. 🤔
  9. Just realised it’s been a month since I last posted! Not too much has happened. A couple of weekends ago my brother came over and I took the opportunity to relocate All the unused boards from Donford Junction out of the way and into the rafters of the garage. This involved a couple of 4’ x 2’ sheets of 12 mm ply to form a platform. Once we had those in position all the boards that formed Donford Junction were lifted up and out of the way. I’m sure the spiders will be having a party up there when summer comes around, but this was needed to remove the need to move boards around every time I needed access somewhere. Also removes the risk of accidentally catching some rail ends! Also manufactured last weekend was the mine control panel. I had hoped to mount the panel in the side on the board as per my earlier installation at Donford Junction. I was looking for a position but, given how far I would have to recess the panel into any backscene in order to protect switches, it looked like I would be compromising the buildings I planned to install. So it was plan B, mount it in a box. I purchased a box from Rapid Online and fixed the panel into the lid. The back of the panel was wired up to 2 multi core cables. One cable for points and one for the position LED feedback from the motors. The other end of the cables are terminated in 15 way D connectors. A couple of stuffing glands secure the cables. The plan is to secure the box under the board when transported and pull the panel out and clip it to the board when in use. The length of the cables will allow the panel to be fixed in several locations depending on the operators preference. Thats it for now. All the best, Andy
  10. Very Sad. 😥 RIP Jonathan
  11. A bit more progress with the track bed cork yesterday and today. Yesterday I installed the cork for the tracks leading up to the loader and screens. I couldn’t resist positioning the building and installing a bit of track and a few wagons to see what it looked like. Today I marked out and installed the cork for the loop at the front of the layout. It’s a bit cold for track laying at the moment. I may have to wait a bit until it warms up. Could be a couple of months! Meanwhile, I purchased an unpowered Proto 2000 E6B unit in Southern livery second hand to run with my Broadway E7A. The picture below is the first time I had placed them together. The colour match is excellent. Very pleased with it. Time to look at positioning a few structures and construct the control panel next All the best Andy
  12. Morning All, hope everyone had a nice Christmas. I have been busy this week constructing the mine screens and loading building. I think this is their first plastic kit I have built in over 25 years! The structure was complete yesterday so I couldn’t resist plonking it on the layout to see how it looked! It’s a bit taller than I was expecting! A few more close up photos below. The roof panels are not fixed in yet, as I intend to enhance the kit by adding over door lights, lights under the loader and on walkways. The base under the slack bin will be trimmed and a track laid beneath for a Gondola wagon to remove the slack. The building will eventually be bolted to the baseboard. Track to be marked out now and the P-Way gang can begin. Wishing everyone a happy new year and good modelling for 2024. All the best. Andy
  13. I would suspect given that the file was posted to RMweb back in 2020, that it was a casulty of the great server crash and recovery. You may have to enquire with the orginal poster if he would be kind enough to re attach it to the thread. Andy
  14. That’s a bit naughty of them. Shame Andy
  15. Lots of pictures on this site as well https://burleycommunitylibrary.weebly.com/railway-station.html Regards Andy
  16. Have you seen this https://www.mediastorehouse.com/network-rail/burley-station-elevation-plan-nd-18309084.html Regards Andy
  17. Bit of an update on my attempts to aquire more structures fot the layout. I recently discovered the Broadway Limited (BLI) had a produced a water tower. Being BLI it wasn't just an ordinary model of a water tower, it was equipped with lowering water shoot and sound effects when in operation! (Link below to BLI page) https://broadway-limited.com/products/7920-operating-water-tower-w-sound-n-w-weathered-ho After searching the internet I managed to find one in the US for a good price and stumped up for the postage. Notification was recieved that it was on its way by USPS express and a tracking number was recieved. After a couple of weeks I thought I would see where it was and I found out it was in Toronto. It was only then, when I opened up the full tracking history, did I discover the air miles it was accumulating and that it had already been in the UK once and then sent off to Toronto after clearing UK customs! When it eventually arrived, I took the tracking data and created a map of its journey..... The package accumulated over 13,000 miles before arriving in Heysham. This must be some sort or record? ( that works out at at around at $0.0026 per mile) After leaving Chicago for its 2nd trip to the UK on a Sunday it was safely delivered to my door the following day. Now all I have to worry about is the call of nature every time its operated and the water starts to flow (sound of anyway)! All the best Andy
  18. Not a lot happening on the actual layout at the moment but a few things going on in the background. I have been working on a few buildings and some DCC aspects including the construction of a DCC programming and test board for my Sprog and LokSound programmer. I do have an ESU test board which I can also plug into the above set by use of the phono plug “switch board “ First job for the new set up was to programme up a LokSound 5 chip for the Z1a ESU conveniently have a downloadable Baldwin Mallet that with a few tweaks to the whistle and air pumps gives a good base for the sound profile. The chip and speaker will go in the tender. Despite the age of this NJ International brass loco I was pleasantly surprised to find the floor of the tender perforated already for the fitting of a speaker. A few more generic building have been added to the stock pile ready for adapting as mine support buildings. There will be no progress this weekend as I will be at Barnsley show operating Wentworth Junction. Andy
  19. Before finishing off the laying of the mine tracks, I found an issue with the mating of the last two boards. No matter how I adjusted the legs I could not get the top of the two boards flat and level. A bit of investigation revealed a warped bit of plywood on the baseboard end which just twisted everything when the bolts were tightened up. The solution was to join the last two boards together permanently with glue, bolts, screws and a half lapped vertical support brace across the joint. The two are now firmly one! The white paper you can see above denotes the mine loading building. Next job was to replace the temporary bracing on the rear spiral board with aluminium bracing and a way of holding the legs closed when folded up. When folded up it looks like this. View of the underside. To retain the legs I’m trying neodymium magnets on the legs against metal plates. A bit messy with the metalset but it was going off fast. No time to finesse! Final job over the weekend was the fitting of the curved front on the master board such that we had room to place building next to the siding. Thanks to @Nicktoix of this parish for this building and a few others yet to come. Thanks also to my brother Ian for coming over this weekend to help sort the woodwork out. On with the mine track laying….. All the best Andy
  20. Loving the low angle pictures 🙂
  21. Now that I have laid the track its safe to construct the Control panel. This will be built into the board to minimise connectors and packing things up after a show! Regards Andy
  22. This the joint in question. this photo has just reminded me that I need to add a couple of droppers now I have cut the joint!
  23. Something you don’t have to worry about with copper clad or even half a Peco point!
×
×
  • Create New...