art54

Hi Eveyone, Anyone out there using jmri to control there layout i can ask a few questions? like how to get it to start up using my lenz system. Thanks.

Hello Mr Dutch_Master, Sorry for not explaining in finer detail, what I should of explained is my class 26 has a lenz decoder which has the abc facility, this was working fine up until cleaning the backs of the wheels with an emery board (instead of removing the bogies). Since then the engine runs better but will not stop at a red signal, when I was cleaning the wheels I made sure all the pickups where touching the backs of the wheels, that's all I can tell you.

Hello again everyone, my problem this time is with a Heljan class 26 which will not stop at a red signal, this has just started after I had a go at cleaning the connections to the back of the wheels, I might have altered which of the pickups should be and shouldn't be touching as I presumed that they should all be touching,has anyone managed to strip down the said engine to get a better way of cleaning the backs of the wheels, i've already tried a wheel cleaning brush to no avail, cheers.

Hello RFS, success, thank you for the instructions after a long battle with this computer and windows 10 im up and running, and I would like to say thank you to all my fellow members who have replied and helped me along the way. From a very happy computer idiot. Arthur

Hi Paul, can you tell this computer dunce how to do this please.

Hi Paul, I've opened the file and gone as far as run as administrator, then I get a window :welcome to the device driver installation wizard: so I accept the agreement and click next, it starts the download then immediately stops and I get the message install failed. I am lost again, Arthur.

Hello keith, I think there is something wrong with the way my laptop is setup, perhaps if I burn it and get a new one I might be able to download the driver.

Hello again Paul, Looking at the list you shown me yours has exe on three of the lists where on my listing there is no exe on any of them, I don't know if this effects the reason I get a different window to fail downloading, thanks for the reply(forgot to mention it on the last blog)

Hi Paul, I've done what you say but when I click the run as administrator the welcome to the device driver installation wizard, then I accept the terms then press next then I see it starts to download and immediately comes up with download fail, I've tried a couple of times and it does the same thing every time uuuggh.

Dear RFS, I've done what you said and when I right click to extract all I get one line saying 23150 custom driver, then when I either right or left click I get a list of various lines which some have different meanings am I doing something wrong? like I said me and computers don't go together, give me something with an engine and wheels any day.

Hi Keith, I have downloaded the file from the lenz website all I need now is how to open the file ,I would appreciate for any help as you can tell i'm not computer literate, can send emails that's about it .

Hi John K, I have only just read your reply I have downloaded the driver zip file may I say thank you at this point, but i'm not very computer friendly and don't know how to extract the file as I open the various windows and not sure which window and how to extract the driver , I would be very grateful if you could explain how to extract it.

Hi everybody, Had a look into settings on windows 10 and the li-usb device was in the listing but had drivers unavailable wrote next to it, so I loaded the cd rom I got with device and still kept coming up with usb not connected, I think i'll just call it a day with this one it didn't cost much of ebay and I also received a couple of gold decoders which was worth it just for those alone. While i'm on has anyone used traintech signals with lenz bm3 modules as I cannot get mine to work as they are pos earth and my signals are neg earth anyone overcome this problem i'd be pleased to know. Thanx to everyone for all the help.

Hi Rob, what I meant when I said hub I meant the usb device which I plug straight into my laptop sorry to cause any confusion.

The usb cable fits into the usb hub no problem I've installed the programmes of the cd rom that came with it, the usb light does not light and the programme keeps telling me its not connected,the greenlight on the usb quickly flashes once as I remove the cable from the hub, ithink either I,ve bought a faulty device or the cable is at fault, will have to try another cable and hope for the best. thanks for the advise and will let you know how I get on . CHEERS