Scale7JB
-
Posts
707 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Events
Exhibition Layout Details
Store
Posts posted by Scale7JB
-
-
Hi everyone, just a quick note to say that the Epping Ongar have a mega lineup for the gala this year.
We will have resident loco Pitchford Hall, which is always a bit of a head turner anyway, joined by Didcot rebuild Lady of Legend and just found out that we will also have LMS Jubilee 'Leander' which is at the end of its ticket.
Come and listen to the big guns being used on the Essex hills which are surprisingly steep.
Take a look at the website for dates. www.eorailway.co.uk
Hope to see you there.
Many thanks.
JB.
- 1
-
Im pretty big on using oil paints for weathering at the moment after watching a video by Jerry Spolema on Youtube.
He is a little different to the guy in your video though, in that Jerry does very 'wet' weathering.
I can take a photo of my Atlas O SW-9 if you fancy..
JB.
- 1
-
Did you manage to make a new tank, boiler and smokebox? Looks like what you had to work with was pretty average..
JB.
- 1
-
Kamiack Falls, is a magnificent layout!
Very much look forward to seeing it again, if I make it.
JB.
-
On 09/02/2022 at 13:29, pwr said:
Thats nice. Whose kit was that if you dont mind me asking?
Paul R
Hi Paul, it was the last K2/2 kit that Fourtrack Models had before Gordon wrapped up the business and sold all the kits to other traders.
This model was pretty heavily modified.
The K2 went to Gladiator Models.
JB.
-
Hi Paul, sent a message on Facebook.
JB.
-
-
-
Looks good, driven the real thing a few times, lovely engine!
JB.
- 1
-
1 hour ago, Michael Edge said:
I hope it stays in one piece. I have done this in the past with rather mixed results, the last one I did came back from the painter broken but I did manage to pin it back together. There is a huge stress on the crankshaft joints when someone squeezes the driving wheels while picking the loco up and the bigger the wheels are the more likely this is to break the axle. I see more damage from locos being gripped tightly (for fear of dropping them) than anything else. When I have built up crank axles for cast iron wheels I have used brass instead of steel axles and these have given no trouble at all. I have considered reproducing a Slater's axle in brass for better soft soldering but haven't tried it yet.
I must admit I'm tempted to do the next one with silver solder. I'm pretty sure that if used in small enough amounts at a time I should be able to get enough heat into it for the silver solder to flow. That should be nigh on indestructible.
I think I may also change the diameter of the crank material swell, its a touch small and I will enlarge to 3/16".
I think I may have done one silly thing yesterday. After soldering with the micro flame i quenched the axle immediately in cold water, and fear I may have caused it to move just the tiniest amount. I'm thinking I should have left it to cool gently which would have stopped any stresses in the metal showing themselves. This however is my error and not the kit so I'm still happy.
JB.
-
Hi Michael, yes soldered to a Slaters axle. Not sure how much detail you need as an answer, but I had to use a micro flame to get enough heat into the whole lot to allow the solder to flow nicely into all the joints.
I also used electrical solder with plenty of powerflow flux to make a stronger join than 145 solder would have given me.
if you need any further information just shout.
JB.
-
Connecting rods in.
JB.
- 6
- 1
-
Much better!
JB.
- 1
- 3
-
Thought I'd crack on with the etched crank webs and produce the axle.
All went very nicely until I'd got it together and found the cranks are 1mm too wide. Damn!Will redo tomorrow.
JB.
- 1
- 1
-
Colin, I think you have the top of the brake hangers sticking out too far out from the inner frames, and that will be the cause of the interaction between buffers and brake hangers.
JB.
-
53 minutes ago, CUTLER2579 said:
JB,
Will definitely be interested in a couple of kits if you go into production with it. Looks superb.
Ah that's great thanks. I have more revisions to do, and also to work out how to do a Finescale version but I think I'm there with how to do it. Will be an add-on etch of course.
Watch this his space but hope to have a properly sorted final prototype for the Kettering show in March. That's what I'm aiming for at least.
JB.
- 2
- 1
-
Sorry, I've loads of photographs of the loco from the tender, but nothing to hand showing inside and details, though I do recall quite well how it does together if not need any info..
JB.
- 1
-
Grabbed a quick video at the end of the day..
JB.
- 4
-
24 minutes ago, Adrian Stevenson said:
Very enjoyable day thanks. It is a great show and rapidly becoming my favourite.
It's a long way from East London!
-
19 minutes ago, Adrian Stevenson said:
I did see it today. It looked great.
Thanks Adrian.
It got some good interests, you should have said hello..
gooefully have sole sole further updates soon, as I need to try the etched valve gear, including making up the crank axle.
Hope you had a good day!
JB.
- 1
-
-
5 hours ago, AdeMoore said:
JB I’m in no way qualified to post here, but a casual observer.
here D16/3 even if that’s the correct prototype! The photo holds up to zooming in and I make out the bottom of the smokebox to be in line with the top horizontal line of rivets on the saddle. Your top photo above shows that exactly. Yours has a lot of daylight under the barrel there must be a reason why the prototype photo doesn’t give that impression.
Reckon you nailed it.
Brilliant work.
Cheers
Many thanks for your casual observations..
Once I have a Chimney on there I can make a final call.
JB.
-
6 hours ago, 30368 said:
Really fine work JB - tempts me to try a 7mm build!
Kind regards,
Richard B
Careful Richard, 7mm is a slippery slope. If you're nearby it is the Bristol Gauge O Guild show tomorrow.
JB.
- 1
-
6 hours ago, Adrian Stevenson said:
Really nice work.
I am looking forward to the show tomorrow.
Cheers, Ade.
Thanks Ade, pop by Love Lane layout, and the loco should be sat in the loco yard unless I'm out taking it to see people about bits and pieces.
JB.
- 1
Epping Ongar Railway Gala - April to May 2024
in Non-modelling Events
Posted
Hi all, a bit more information for the upcoming weekends.
Many thanks.
JB.