HonestTom Posted February 21, 2019 Share Posted February 21, 2019 (edited) Here’s a minor bash for New Ankh. I wanted a careworn mid-Victorian locomotive that I could also use on other layouts. It’s just a Hornby Holden tank with a cut back cab and the copper cap replaced with the cap from a Rocket kit. It’s nothing fancy, but it looks the part. Just needs a crew now. EDIT: Yikes, I didn't realise how big these photos were. Sorry chaps. Edited February 22, 2019 by HonestTom 10 1 Link to post Share on other sites More sharing options...
Popular Post Tullygrainey Posted March 10, 2019 Popular Post Share Posted March 10, 2019 (edited) Another bash of the long suffering Hornby Caledonian Pug. This is NCC Class N 0-4-0ST Number 16, built in 1914 by the LMS Northern Counties Committee in Belfast's York Road works. It shunted the Belfast harbour lines for most of its life and passed eventually to the Ulster Transport Authority who took it out of service in 1951. Pictures etc. of the prototype: here, here and here Mods to the crosshead/slidebars were done with advice gleaned from this thread - see Stringfingerling's post of 4 May 2018. A scratch build would've been more accurate but then... a) that would have been beyond me, and b) it wouldn't be a Pugbash would it? Alan Edited December 14, 2022 by Tullygrainey 21 15 Link to post Share on other sites More sharing options...
Ruston Posted March 10, 2019 Share Posted March 10, 2019 That's probably the best bash of one of those pugs that I've seen. I would never have guessed that's what it started out as. 9 1 Link to post Share on other sites More sharing options...
Tullygrainey Posted March 10, 2019 Share Posted March 10, 2019 (edited) On 10/03/2019 at 19:21, Ruston said: That's probably the best bash of one of those pugs that I've seen. I would never have guessed that's what it started out as. Thank you. I'm very pleased that you like it. I have to admit there wasn't much Caley Pug superstructure left by the time I'd finished. About this much: Edited December 14, 2022 by Tullygrainey 1 Link to post Share on other sites More sharing options...
Gibbo675 Posted March 10, 2019 Share Posted March 10, 2019 8 hours ago, Tullygrainey said: Another bash of the long suffering Hornby Caledonian Pug. This is NCC Class N 0-4-0ST Number 16, built in 1914 by the LMS Northern Counties Committee in Belfast's York Road works. It shunted the Belfast harbour lines for most of its life and passed eventually to the Ulster Transport Authority who took it out of service in 1951. Pictures etc. of the prototype: here, here and here Mods to the crosshead/slidebars were done with advice gleaned from this thread - see Stringfingerling's post of 4 May 2018. A scratch build would've been more accurate but then... a) that would have been beyond me, and b) it wouldn't be a Pugbash would it? Alan Hi Alan, The slide-bars make all the difference to the chassis and that is not to ignore the work on the superstructure ! Gibbo. 1 2 1 Link to post Share on other sites More sharing options...
Tullygrainey Posted April 16, 2019 Share Posted April 16, 2019 On 14/04/2019 at 12:58, ianofsklr said: I have been using a Hornby Caledonian pug for the running plate and saddle tank, and Nellie for the cab and smoke box (chimney had long gone). I am am hoping to fit it on to a Bachmann Greg chassis and I want to make it DCC. The Greg I bought had had the chip removed so I thought a Hornby Peckett decoder would be nice and small so it would fit inside my new loco body. I need to do some soldering to put it all together and I thought I knew how to do it, but the more I look about it the more confused I get. How might you wire it together? You might even suggest a different decoder, perhaps even the original decoder for Greg if I can find one to buy. (Body is not properly mounted which is why it looks wonky). Looking good! The simplest way to hardwire a decoder is to dispense with any extra circuit boards and solder the decoder wires directly to motor and pickups. With a standard 8 pin decoder, this would be red and black to the pickups, orange and grey to the motor. I've never used a Hornby 4 pin decoder so I'm not sure if the same colours apply. Anyone? Alan 1 Link to post Share on other sites More sharing options...
RJS1977 Posted April 16, 2019 Share Posted April 16, 2019 46 minutes ago, Tullygrainey said: Looking good! The simplest way to hardwire a decoder is to dispense with any extra circuit boards and solder the decoder wires directly to motor and pickups. With a standard 8 pin decoder, this would be red and black to the pickups, orange and grey to the motor. I've never used a Hornby 4 pin decoder so I'm not sure if the same colours apply. Anyone? Alan Remember to disconnect the pickups from the motor first though, otherwise you will put a DCC signal on the wrong side of the chip and fry it! 1 1 Link to post Share on other sites More sharing options...
Robin Verth Posted April 16, 2019 Share Posted April 16, 2019 The Hornby 4 pin decoder follows convention it only has thr black, red, orange & grey wires are used. 1 1 Link to post Share on other sites More sharing options...
Ruston Posted April 17, 2019 Share Posted April 17, 2019 On 14/04/2019 at 12:58, ianofsklr said: I have been using a Hornby Caledonian pug for the running plate and saddle tank, and Nellie for the cab and smoke box (chimney had long gone). I am am hoping to fit it on to a Bachmann Greg chassis and I want to make it DCC. The Greg I bought had had the chip removed so I thought a Hornby Peckett decoder would be nice and small so it would fit inside my new loco body. I need to do some soldering to put it all together and I thought I knew how to do it, but the more I look about it the more confused I get. How might you wire it together? You might even suggest a different decoder, perhaps even the original decoder for Greg if I can find one to buy. (Body is not properly mounted which is why it looks wonky). Just an observation here but that doesn't seem to be plausible in the real world. 0-4-0 tank engines tend to have the firebox behind the rear axle, whereas yours has it in front, so the valve gear would have to somehow run off the front axle as you haven't got any outside valve gear. There's a large overhang from the front axle to the front of the loco and so it would have far too much weight over the front axle as the firebox being behind the rear axle usually balances out the weight of the cylinders at the front end on engines with a short wheelbase. With the boiler ending where it joins the cab it leaves the cab looking far too spacious for any practical purpose. 1 2 Link to post Share on other sites More sharing options...
Ruston Posted April 18, 2019 Share Posted April 18, 2019 (edited) 41 minutes ago, ianofsklr said: I am a bit out of my depth with axles and firebox positions, but I will give it some thought. I am thinking I might move the chassis as far forwards as I can and possibly reduce the cab or the bunker to increase the distance between the firebox and the rear axle. I might revisit an earlier idea to make it an 0-4-2. I was planning to use Greg's cylinders - would this help with the imbalance that you suggest would happen with the large overhang? It's the cylinders that contribute to the imbalance in your design. In the real world they are heavy and the firebox being outside the wheelbase at the other end would balance that weight out but your design has the firebox between the axles. I agree that an 0-4-2 would be a better idea. Below is a rough rearrangement of your photo. I've moved the cab forward and shortened the saddle tank and have also shortened the overall length by shortening the running plate. Now all of the firebox would be inside the cab and behind the rear axle (the white part of what was the firebox, in front of the cab, is now a tank support). The chassis that you want to use is now right up to the front and there is a set of wheels under the cab, which carry the weight of the long overhang at the rear. Edited April 18, 2019 by Ruston 3 1 Link to post Share on other sites More sharing options...
RMweb Gold Corbs Posted April 18, 2019 Author RMweb Gold Share Posted April 18, 2019 I had a similar issue when I used almost exactly the same components to build an 0-4-0ST What I ended up doing was shortening it by chopping out the straight section of bunker and the area of cab in front of the cut-out to help reduce the overhang. I used a slightly shorter wheelbase chassis but still has big overhangs front and rear. It's not 100% but if I squint I can pretend the firebox is just behind the axle 5 Link to post Share on other sites More sharing options...
Ruston Posted April 21, 2019 Share Posted April 21, 2019 (edited) Does anyone know which issue of Railway Modeller contained the article where someone used a Nellie body on an 0-6-0 chassis? It was in the last 2 or 3 years. Edited April 21, 2019 by Ruston Link to post Share on other sites More sharing options...
RMweb Premium BSW01 Posted April 21, 2019 RMweb Premium Share Posted April 21, 2019 19 minutes ago, Ruston said: Does anyone know which issue of Railway Modeller contained the article where someone used a Nellie body on an 0-6-0 chassis? It was in the last 2 or 3 years. It was in the May 2018 edition 1 Link to post Share on other sites More sharing options...
Ruston Posted April 25, 2019 Share Posted April 25, 2019 Can I join the party? I was looking for a Nelllie, or 7178 but the huge dome on this one has a certain charm about it. As it's a body only I have to work out the ride height, so here it is propped up on card supports to match a decent RTR wagon. In this case a Bachmann model of a standard 1923 pattern RCH coal wagon. Now to work out what to put under it... 7 Link to post Share on other sites More sharing options...
RedGemAlchemist Posted April 25, 2019 Share Posted April 25, 2019 2 hours ago, Ruston said: Now to work out what to put under it... I thought about turning mine into an 0-4-2T at one point before deciding to leave it as is. You could try that. Link to post Share on other sites More sharing options...
Ruston Posted April 25, 2019 Share Posted April 25, 2019 3 hours ago, RedGemAlchemist said: I thought about turning mine into an 0-4-2T at one point before deciding to leave it as is. You could try that. You must have read my mind. I've been looking through my box of bits and have found a chimney, a toolbox, a Westinghouse brake pump and a whistle for the project. I have also found a gearbox and have several motors to choose from. I just have to get some wheels and make the frames. Handrails filed off the smokebox, cab doors/handrails sawed and filed away, bunker hollowed out and the edge filed to a curve, lamp irons filed off the bunker rear and the hole in the rear given some plastic filler. 8 Link to post Share on other sites More sharing options...
Ruston Posted April 27, 2019 Share Posted April 27, 2019 Chopping out the insides. There was an annoying moulding lump under the boiler, and a tube poking out from the bottom of the dome that have been scraped away. I had hoped that the dome would be removable, so I could take it off and preserve it from accidental damage but although it is a seperate part it is firmly glued on. Around the doors the cab wall was double thickness, so this has been filed down. The saw cuts near the front are the start of cutting out the lower part of the smokebox as the moulding here will otherwise foul the new wheels. Frames. 38 thou. thick brass, with 1/16th brass stretchers, soldered together. The gearbox is an unknown and the motor is one of those Chinese Mirsumi things, bought from ebay for under a pound. It's soldered on to the gearbox as the holes in the 'box and motor don't match. Even if they did I don't have any screws. 6 4 Link to post Share on other sites More sharing options...
RedGemAlchemist Posted April 28, 2019 Share Posted April 28, 2019 3 hours ago, ianofsklr said: I fitted some handrails and I will fit buffers and a smoke box dart, all from Phoenix Paints (and I am thankful for good customer service). I have also been filling and filing, and therefore it currently looks a bit scruffy. I did wire up the decoder, and it did work but then the black wire on the decoder came out and although I soldered it back in it doesn’t work at the moment. I decided not not to shorten the loco but I turned the chassis around and I will fit a 9F front pony truck on to the rear of my chassis to make it an 0-4-2. I think that the 9F wheels are about the right size, being smaller than the wheels from Greg, so I am looking out for one of those. Halfords don’t do a very purple spray (like the picture) but they do do some very dark blues which are my current favourite, that or a turquoise colour. I wanted to have something unusual. Hmm. You don't see many 0-4-2 saddle tanks. I'm interested to see how it goes. Link to post Share on other sites More sharing options...
rockershovel Posted April 28, 2019 Share Posted April 28, 2019 (edited) Kerr Stuarts and Falcon apart, there’s this from Baldwin - seems to be mostly a narrow gauge configuration Edited April 28, 2019 by rockershovel 2 Link to post Share on other sites More sharing options...
RJS1977 Posted April 28, 2019 Share Posted April 28, 2019 Intriguingly, the Revd Awdry's Mid Sodor Light Railway 'had' a Kerr Stuart, a Falcon and a Baldwin which only appeared in a couple of illustrations in 'Duke The Lost Engine' as a stationary boiler but which Awdry had apparently invented a backstory for as part of 'The Island of Sodor - Its People, History and Railways', where it was called 'Stanley'! I'd always assumed it was a side tank, but perhaps it was one of these? Link to post Share on other sites More sharing options...
Ruston Posted April 28, 2019 Share Posted April 28, 2019 (edited) Nellie boshed some more. Driving rods made from Nickel Silver. I cut the boiler section out in order to make the removal of the toolboxes easier. This done I really couldn't put it back without having light under the high-pitched boiler, so some 1.5mm thick styrene sheet was cut into a strip and dunked in boiling water, clamped around a tube. The boiling water allows it to retain its shape after it has cooled. A piece was cut off and spliced in to the original boiler barrel (inset photo). Cutting the boiler, using a razor saw, on the boiler band meant that I not only lost the band but lost about 60 thou, length from the cuts, so the ring was fixed with MEK to a sheet of plasticard and cut and filed inside and out, with the outside standing proud to now become the new boiler band. Chunks of styrene fixed to the body, using MEK, drilled for self-tapping screws to hold the frames to the body. The plasticard frame plate is drilled ready for the tedious fitting of lots of tiny lengths of styrene rod as rivets. Hand rail across the smokebox front carefully filed off and holes for brass posts drilled. Smokebox door handle detail filed off. Boiler refitted and splasher trial-fitted but not yet fixed. I won't fit the splasher properly until I have wheels and can check the clearances. The proper circular boiler now means that I can't use the motor and gearbox that I intended to use as it won't fit at all on the front axle now and the motor is too large to fit in the smokebox if I powered the centre axle. Ah well, back to the drawing board on that one... Edited April 28, 2019 by Ruston 9 1 3 Link to post Share on other sites More sharing options...
Popular Post Ruston Posted April 28, 2019 Popular Post Share Posted April 28, 2019 I forgot about one I did last year. From this: To this: Dowlais Iron Co. Class D as it should be. Cut n shut body, new frames wheels and motor, Bachmann buffers, brass wire handrails and custom etched plates by Narrow Planet. It really needs lining but that's beyond my skillset. 17 8 Link to post Share on other sites More sharing options...
RMweb Premium Compound2632 Posted April 28, 2019 RMweb Premium Share Posted April 28, 2019 7 minutes ago, Ruston said: Iowlais Iron Co. Class D as it should be. Cut n shut body, new frames wheels and motor, Bachmann buffers, brass wire handrails and custom etched plates by Narrow Planet. It really needs lining but that's beyond my skillset. I'm looking for the keyhole on this one... 1 2 Link to post Share on other sites More sharing options...
Ruston Posted April 28, 2019 Share Posted April 28, 2019 11 minutes ago, Compound2632 said: I'm looking for the keyhole on this one... It does look rather as if it's from the imagination of a clockwork train designer but it is absolutely real. http://www.irsociety.co.uk/Archives/25/picture_parade_25.htm 2 1 Link to post Share on other sites More sharing options...
RMweb Premium Compound2632 Posted April 28, 2019 RMweb Premium Share Posted April 28, 2019 17 minutes ago, Ruston said: It does look rather as if it's from the imagination of a clockwork train designer but it is absolutely real. http://www.irsociety.co.uk/Archives/25/picture_parade_25.htm Well you could knock me down with a feather! Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now