Jump to content
 

Yet another Work Bench - West Coast Mainline Focused


Recommended Posts

Next thing on the books is to put sound and lights onto my two Patriot 4-6-0 class locomotives. 

 

I have Hornby 45528 - R.E.M.E. and 45531 - Sir Frederick Harrison which I will also rename to 45521 - Rhyl and 45532 - Illustrious respectively.

 

post-23457-0-09385800-1510903979_thumb.jpg

 

First Thing I do whenever I do an install is to completely disassemble the loco and remove all unwanted wiring as I always hardwire the decoders into my locos to ensure a solid connection. This also removes the change of the PCB failing on me and removes joints that could fail down the line. 

 

post-23457-0-09800400-1510904033_thumb.jpg

 

I will generally work on the part where the decoder will not be located first as this part is fairly straight forward to do. In this case the tenders are where the speakers are going to be located and so I removed the weight and cut out a section of the coal bunker to allow for a larger speaker and creates a bit more air space for the sound to reverberate. 

 

post-23457-0-69497600-1510904203_thumb.jpg

 

post-23457-0-28248100-1510904258_thumb.jpg

 

post-23457-0-62331300-1510904439_thumb.jpg

 

I will then cut the power wires where they attached the the contacts at the front end of the tender and will drill a hole to allow the wires to be feed through and out the underside of the tender and eventually up and into the locomotive.

 

post-23457-0-08709100-1510904666_thumb.jpg

 

Having done the modifications I will add Lead stripes around the internal sides of the tender body shell to replace the weight that was removed and will act as sound absorption stopping the body from rattling when the sound is on. This make the sound clearer and boomier. 

 

post-23457-0-96147100-1510904735_thumb.jpg

 

Once done I will place the speaker on the chassis and attach black extension wires to it feeding them out of the hole made earlier and I will also do the same with the pick up wires making sure to note which is right and left. I will also now put a piece of card in the coal bunker and glue in place to fill the hole made to fit the speaker. Later I will paint over this and place a coal load on top making it so no one but I shall know any better. Then I re-assemble the tender and that part is done. One thing to note is that removing the factory weight means I loose my locking point for the rear part of the tender body shell. I cut off the internal clip and when I place the shell back on I place a couple drops of plastic cement and this holds the shell on nicely.

 

Now on to the front part of the locomotive. 

 

Here I am placing working loco lamps from DCCconcepts which I have always used and fine them brilliant. Fiddly yes so if you have unsteady hands get someone who does to do this part for you. 

I first make sure to spray the lamps before installing them. I am using black lamps so I spray them a flat black to color them a bit and prevent any light leakage. 

 

post-23457-0-25824700-1510905641_thumb.jpg

 

I then drill the holes for the lamp wires to go through. I will do this a couple of millimetres from the lamp bracket and them feed the wires through and glue the lamps in place. I also tie the wires off around the buffers to help hold the lamps in position while the glue is drying.   

 

post-23457-0-95946000-1510905577_thumb.jpg

 

Once set I will now run the wires under the locomotive shell and into the boiler where the decoder will be. I do this by cutting channels with a dremmel and engraving bit. I will then use plastic cement and glue the wires down into the channels bit by bit ensuring to keep tension on the wire until it sets. Running the wires this way will make sure that they do not get crimped or in any way damaged when the shell is placed back on to the chassis. also if you braid the wires they are a lot easier to run and it keeps everything neater.

 

post-23457-0-58391100-1510905686_thumb.jpg

 

post-23457-0-62010200-1510905744_thumb.jpg

 

After all this we locate the decoder on the place where the 8 pin socket was and remove the lugs. Then place the decoder on a piece of double sided foam mounting strip. 

 

post-23457-0-30811300-1510907013_thumb.jpg

 

Next job now is to run the wires to the motor and connect all the track power wires along with the speaker wires from the tender. The Purple, Yellow and Green wires get isolated and put to one side leaving the Blue and White for the front lights. I put these into one end of a plug along with a 1k resistor on the Blue wire and then attach the wires from the lamps on the other end making sure to match the positive and negative ends correctly. The plug allows me to disconnect the body from the chassis in case I need to get into the locomotive for servicing later on. 

Last thing is to tidy of the wiring and get the shell back on and test. 

 

post-23457-0-30009000-1510907051_thumb.jpg

 

post-23457-0-27732900-1510907174_thumb.jpg

 

Next step is the renaming and weathering. 

 

But before I weather them I will be adding sound into my newly arrived Duchess!!!

Edited by cooley_boy
Link to post
Share on other sites

  • 1 month later...

Its been awhile but I have now finally had a chance to start weathering my KFA timber carrying wagons. 

 

These are about half way through. There is more detailing in the weathering to do and then next the loads themselves. 

 

post-23457-0-66109200-1515050686_thumb.jpg

  • Like 4
Link to post
Share on other sites

  • 3 weeks later...
  • 4 weeks later...

With all the KFA wagons now finally weathered it is time to make a start on the Timber loads. 

 

Now near where I live there is a tree species of which the bark on it branches, particularly on the outer ends, looks like pine bark. 

So I went out and found one with some dead branches on it. Collecting the dead branches are far easier and doesn't hurt the tree. 

 

I then break off all the parts that I want with twigs ranging from 2mm - 5mm in diameter with straight sections on them to be cut out and recreate logs of 6" to 15" in scale. 

 

First step is to cut them to length and then stack them. I will glue them together later and them seal them. 

I will be looking at staining them slightly just the darken the bark a bit to look more like pine.

 

post-23457-0-78263200-1519096542_thumb.jpg

 

post-23457-0-22655100-1519096606_thumb.jpg

 

post-23457-0-70597200-1519096754_thumb.jpg

  • Like 1
Link to post
Share on other sites

  • 1 month later...
  • 4 weeks later...
  • 3 months later...

Well now there are 5 of these wagons finished and ready to roll even with removable loads. No I know there are a few details that are not fully true to life but all in all these do capture the look of these wagons in my view. No just to finish off the last 10.


 


blogentry-23457-0-12229000-1533868151_th


 


blogentry-23457-0-93657300-1533868257_th


 


blogentry-23457-0-50222200-1533868342_th


 


blogentry-23457-0-21060100-1533868396_th


 


blogentry-23457-0-70093900-1533868438_th

  • Like 5
Link to post
Share on other sites

Well now that I finally have the new Freightliner Class 70 from Bachmann I have done the usual running procedure and commissioning before the loco will be added to the running roster. 

Now in the process of adding sound and adjusting the lights as needed. 

 

I do think I may need to put the loco back together at some point though........

 

post-23457-0-21752100-1533870928_thumb.jpg

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...