hayfield Posted August 27, 2021 Share Posted August 27, 2021 Phil The three I bought were complete, but it was weeks ago and I cannot remember Link to post Share on other sites More sharing options...
RMweb Gold The Fatadder Posted September 12, 2021 RMweb Gold Share Posted September 12, 2021 Does anyone have experience of the Falcon Bulldog kit? I have just purchased the curved frame version off eBay, with the initial intention of just using its bogie, chassis parts and con rods along with a nicely made cast version for which I purchased a while back. however I now see that I have bought a curved frame version, which would be a nice addition to the Bird and shallow frame versions I already have. So I am now getting tempted to build this in full. I know Falcon have something of a reputation, so thought I’d ask for advice now… I don’t think the etches come with instructions (though how useful they would be I don’t know), and I’d need castings (but Brassmasters could fill in for most of it on that front)…. Link to post Share on other sites More sharing options...
RMweb Premium Siberian Snooper Posted September 12, 2021 RMweb Premium Share Posted September 12, 2021 See my comment on your thread. 1 Link to post Share on other sites More sharing options...
hayfield Posted September 12, 2021 Share Posted September 12, 2021 2 hours ago, The Fatadder said: Does anyone have experience of the Falcon Bulldog kit? I have just purchased the curved frame version off eBay, with the initial intention of just using its bogie, chassis parts and con rods along with a nicely made cast version for which I purchased a while back. however I now see that I have bought a curved frame version, which would be a nice addition to the Bird and shallow frame versions I already have. So I am now getting tempted to build this in full. I know Falcon have something of a reputation, so thought I’d ask for advice now… I don’t think the etches come with instructions (though how useful they would be I don’t know), and I’d need castings (but Brassmasters could fill in for most of it on that front)…. I have bought 3 of the latest etched only kits, 2 tanks and a curved frames Bulldog like yourself. The initial plan was to build these using appropriate whitemetal kits to make hybrid models, using sheet metal parts where they look best and cast when cast parts are better. whilst the etching is far better quality than its predecessors, they are still Jedinco kits. As far as I am concerned these are a scratch builders aid/ kit bash project. If bought at the right price they are cheap as chips, but the design quality is no up to modern standards 1 Link to post Share on other sites More sharing options...
RMweb Gold The Fatadder Posted September 12, 2021 RMweb Gold Share Posted September 12, 2021 Will look forward to hearing how you get on with it I think from reading these comments I will stick with my original plan and pinch the chassis from these etched and use it with my white metal one. If at some point I’m bored and looking for a project, will then see what can be done with the body etches Link to post Share on other sites More sharing options...
Steamport Southport Posted September 12, 2021 Share Posted September 12, 2021 The instructions will be very basic. The only one I've got is a HR Clan 4-6-0. You got a drawing of the locomotive. A drawing of the etches and a page of typed instructions. Most of which are "Take part and solder to other part". Thankfully the boiler and smokebox are rolled. I wouldn't fancy rolling those without a roller. But the etchings and castings are very good. I don't fancy tackling the valve gear just yet though, looks complicated. So one for the future I feel. Jason Link to post Share on other sites More sharing options...
hayfield Posted September 12, 2021 Share Posted September 12, 2021 15 minutes ago, Steamport Southport said: The instructions will be very basic. The only one I've got is a HR Clan 4-6-0. You got a drawing of the locomotive. A drawing of the etches and a page of typed instructions. Most of which are "Take part and solder to other part". Thankfully the boiler and smokebox are rolled. I wouldn't fancy rolling those without a roller. But the etchings and castings are very good. I don't fancy tackling the valve gear just yet though, looks complicated. So one for the future I feel. Jason Jason What is being sold are etches only, no castings or instructions. In the case of the Bulldog there is no tender. As I said its a basic etch(s) and that's it 1 Link to post Share on other sites More sharing options...
Steamport Southport Posted September 13, 2021 Share Posted September 13, 2021 18 hours ago, hayfield said: Jason What is being sold are etches only, no castings or instructions. In the case of the Bulldog there is no tender. As I said its a basic etch(s) and that's it Mine came from a different source. I was trying to point out the instructions are next to useless anyway in response to this. 21 hours ago, The Fatadder said: I don’t think the etches come with instructions (though how useful they would be I don’t know), Jason Link to post Share on other sites More sharing options...
RMweb Gold The Fatadder Posted September 13, 2021 RMweb Gold Share Posted September 13, 2021 2 hours ago, Steamport Southport said: Mine came from a different source. I was trying to point out the instructions are next to useless anyway in response to this. Jason Certainly useful for me to know as I had been planning to ask if anyone had the instructions for said Bulldog they could scan (if the etches turned up without any). From that description Im guessing there isnt much point! Link to post Share on other sites More sharing options...
RMweb Gold The Fatadder Posted September 14, 2021 RMweb Gold Share Posted September 14, 2021 @hayfield On your Bulldog did you get a pair of frames? Mine arrived this morning, and only has included the right hand frame/rivet detail /bogie side frame. I have messaged them back via ebay to clarify I am assuming that I was purchasing from Falcon direct given the number of etch kits in new packaging they were selling. But would be good to clarify Link to post Share on other sites More sharing options...
RMweb Gold chris p bacon Posted September 14, 2021 RMweb Gold Share Posted September 14, 2021 Just now, The Fatadder said: I am assuming that I was purchasing from Falcon direct given the number of etch kits in new packaging they were selling. You are purchasing from a private individual who is not listed as an owner of Falcon. The listings are a case of 'what you see, you get' 1 Link to post Share on other sites More sharing options...
RMweb Premium Tim Dubya Posted September 14, 2021 RMweb Premium Share Posted September 14, 2021 19 hours ago, The Fatadder said: Certainly useful for me to know as I had been planning to ask if anyone had the instructions for said Bulldog they could scan (if the etches turned up without any). From that description Im guessing there isnt much point! I suspect if there are any, they'll be on Falcon's website. Link to post Share on other sites More sharing options...
Brassey Posted September 14, 2021 Share Posted September 14, 2021 7 hours ago, The Fatadder said: arrived this morning, and only has included the right hand frame/rivet detail /bogie side frame. i too acquired a kit and it appears to be short of an etch for one side of the frames. Also, my quick look, suggests there are footplates for both the curved and straight frames. Any response to the query via eBay? Link to post Share on other sites More sharing options...
RMweb Gold The Fatadder Posted September 14, 2021 RMweb Gold Share Posted September 14, 2021 18 minutes ago, Brassey said: i too acquired a kit and it appears to be short of an etch for one side of the frames. Also, my quick look, suggests there are footplates for both the curved and straight frames. Any response to the query via eBay? Was yours the same frame etch as this one? Was surprised to see that the kit included etches for cabs, frames and footplate for both versions. If it had included the etch for both sides it would have a lot of useful parts. No response via eBay yet, I will likely raise a dispute and try and get a partial refund for the missing bits if they can’t supply it Link to post Share on other sites More sharing options...
RMweb Premium Siberian Snooper Posted September 14, 2021 RMweb Premium Share Posted September 14, 2021 From memory the kit was designed to cover all three variants of the Bulldog. I bought my kit at a Bristol show, when it was held in Bristol docks warehouse, I mentioned to the then proprietor that I was only interested in the curved framed variant and he took out the castings for the straight and deep framed locos. Link to post Share on other sites More sharing options...
Brassey Posted September 14, 2021 Share Posted September 14, 2021 1 hour ago, The Fatadder said: Was yours the same frame etch as this one? Was surprised to see that the kit included etches for cabs, frames and footplate for both versions. If it had included the etch for both sides it would have a lot of useful parts. No response via eBay yet, I will likely raise a dispute and try and get a partial refund for the missing bits if they can’t supply it I’ve not looked but from memory my fret is the same. The frets are probably just handed and possibly from the same artwork but the missing one is reversed. It would not be impossible to produce the missing fret if it was never etched in this batch. i too was surprised to find parts for both versions when it is described as curved framed. But IIRC there is only one firebox. I’m not too concerned about the missing parts because I have all I needed and it wasn’t the frames in this instance. I treat these etches as scratch building aids that will save me time. oddly, I also have a Mallard Duke etch that has bits missing so I probably have enough bits to build a curved frame Bulldog or another Duke if I ever need to. Link to post Share on other sites More sharing options...
Brassey Posted September 15, 2021 Share Posted September 15, 2021 I thought the law of Sod would kick in here but fortunately I have sufficient parts on the both etches now for the left and right frames of a curved frame Bulldog or Duke. There is a lot missing on the Mallard fret: Again looking at the chassis fret, there is a chassis for the tender but no body? The label on the package mentioned a tender... Link to post Share on other sites More sharing options...
micklner Posted September 15, 2021 Share Posted September 15, 2021 Sadly this has become another version of the comments, starting on page 1 , if anybody has'nt read the first page of this thread, I suggest you do so, before ordering items. The only thing that has improved, is people are actually getting something for their money. Many did'nt back in 2018 including myself, I wont get caught again. At least it is a "kit" of sorts is now being recieved, albeit very poorly described and missing parts/sheets of etches. Buyer beware still applies, as in the starting heading. Link to post Share on other sites More sharing options...
hayfield Posted September 17, 2021 Share Posted September 17, 2021 On 13/09/2021 at 17:02, The Fatadder said: Certainly useful for me to know as I had been planning to ask if anyone had the instructions for said Bulldog they could scan (if the etches turned up without any). From that description Im guessing there isnt much point! I am away at the moment so cannot check. As I said all along I bought my 3 kits of parts with the view of using them along with white metal kits I have, making three hybrid kits. Look at the starting prices, when they are cheap there is a reason. Some of the latest ones started at £10, common sense must tell you there is a reason for this when other lots are going for higher prices I was tempted to buy another in the latest selection but only if I could buy it/them at a knock down price. All along I have stated they may be incomplete and pay for what you can see, not what you hope is there. We all like a bargain. But when you see a retail price in the £50’s and it’s £10 or £20 it’s that low for a reason Link to post Share on other sites More sharing options...
PenrithBeacon Posted September 17, 2021 Share Posted September 17, 2021 On 14/09/2021 at 12:48, Tim Dubya said: I suspect if there are any, they'll be on Falcon's website. Nothing seems to be available! I have put a query of Falcon Brass Kits on eBay and got nothing from a Samantha in return. Link to post Share on other sites More sharing options...
RMweb Gold chris p bacon Posted September 17, 2021 RMweb Gold Share Posted September 17, 2021 As far as I know this is the only 'kit' listed https://www.ebay.co.uk/itm/LSWR-Drummond-M7-Passenger-Tank-4mm-Scale-Loco-chassis-Etches/324792738310 I noted that the starting bid is £1.66 less than the price of the body kit (the chassis would have been another £20.) At that starting price I'd rather hope it was all there. Link to post Share on other sites More sharing options...
hayfield Posted September 18, 2021 Share Posted September 18, 2021 14 hours ago, chris p bacon said: As far as I know this is the only 'kit' listed https://www.ebay.co.uk/itm/LSWR-Drummond-M7-Passenger-Tank-4mm-Scale-Loco-chassis-Etches/324792738310 I noted that the starting bid is £1.66 less than the price of the body kit (the chassis would have been another £20.) At that starting price I'd rather hope it was all there. Dave As you say, look at the starting price. Some of those just sold started at £10 others at £20. Surely at these starting prices something is adrift. Earlier in the thread it was reported cheaper tender locos were without tenders 1 Link to post Share on other sites More sharing options...
RMweb Premium Tim Dubya Posted September 18, 2021 RMweb Premium Share Posted September 18, 2021 (edited) 22 hours ago, PenrithBeacon said: Nothing seems to be available! I have put a query of Falcon Brass Kits on eBay and got nothing from a Samantha in return. The seller is listed as hatuk73 on eBay. Nothing much there now but check back tomorrow or Monday, there was a complete kit (Inc castings) for a LSWR 24' Luggage Van last week. The loco kits are just etches for either body or tender or chassis. There used to be "instructions" on the Falcon site, certainly for some of the wagons but tbh even these were useless (I used a book when building a ling kit). Cheers Dubs Edited September 18, 2021 by Tim Dubya vitamin C Link to post Share on other sites More sharing options...
Brassey Posted November 26, 2021 Share Posted November 26, 2021 Further issues regarding the Falcon Bulldog I’m afraid. Having made various starts, I’ve now noticed that the bogie frames on the chassis etch are short on the wheelbase. Luckily I have an alternative. Link to post Share on other sites More sharing options...
hayfield Posted November 27, 2021 Share Posted November 27, 2021 11 hours ago, Brassey said: Further issues regarding the Falcon Bulldog I’m afraid. Having made various starts, I’ve now noticed that the bogie frames on the chassis etch are short on the wheelbase. Luckily I have an alternative. This make of kits were always a hassle to make, simply as they were made in the early days of etched kits, plus the massive output of different models in a very short time. Though the castings and turnings on the whole were of excellent quality The kits themselves in most cases certainly will not fall together and will need an experienced hand to get them built. I enjoy reading Jazz's updates in 7mm scale loco building, quite often he has to modify etched parts to fit. Thankfully things have moved on with new kits As for their following, Jidenco and Falcon Brass kits on the second hand market often fetch very good money, seems many are happy to overlook the odd issue or two. Certainly with the latest etch only releases I will use mine in conjunction with parts from other kits ( composite building) 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now