RMweb Gold Firecracker Posted September 27, 2020 Author RMweb Gold Share Posted September 27, 2020 So, the latest wagons have emerged from hiding. Then, after a need to get to the little mill (blasted customers!) and storing next door’s dishwasher for a week (it makes perfect sense in context, honest!) the layout has been put back up and here’s a few shots, including the latest arrivals. Owain 12 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted September 29, 2020 Author RMweb Gold Share Posted September 29, 2020 Today’s project, a brace of 12t vans. Both a bit different, first up is a ply sided fitted with one of the clasp braked underframes. So here it is on the surface plate drying true. A close up of the underframe (Solebars and brake gear from the Red Panda kit) And ready for primer. Next up, is one of the diag. 1/212 margarine vans. Inspired by reading Rowland’s book and a sheet of transfers, aparently 3 grounded bodies and 1 intact van (arbeit heavily modified) from this diagram survive, so I decided 1 more was feasible. So it’s a parkside kit, with the unused oleo-fitted bufferbeams from the Red Panda kit used above grafted onto the ends. Finally, the Chivers 21t mineral has gained its transfers and been gently weathered. A few little touch ups and a coat of varnish to go, but a very nice kit to build. Owain 4 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 4, 2020 Author RMweb Gold Share Posted October 4, 2020 (edited) A bit more. First, during a bumper airbrush cleaning session, my 10 year old Aldi special ultrasonic bath decided to expire (first the timer became a random number generator, then the buzzing changed pitch quite impressively, it gave a sizzling noise and then sprung a terminal smoke leak). It’s paid for itself many times over and is a very useful bit of kit, so amazon obliged with a replacement. Which is a bit bigger, but rather nice and damned eff3ctive. Next up, the vans seen above have been primed, airbrushed with Valejo’s cavalry Brown, roofs/underframes brush painted and have started to gain their transfers. Next, the restoration of the Airfix/Dapol meat van. This was built 30-odd years ago in a collaboration between me and my father (I built it and did the transfers, he painted it), so it’s gained replacement doors (parkside spares) which have touched up beautifully. Beyond fitting Kadees, touching up the underframe and a coat of varnish, I don’t plan to do much more to it. Finally, a bit of planning. Might happen, might not, but an idea for an extension over two boards, with a new fiddle yard and partly low relief Sedbergh MPD. Don’t start with the negative waves about will it fit in the garage... Owain Edited October 4, 2020 by Firecracker 6 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 6, 2020 Author RMweb Gold Share Posted October 6, 2020 One of the last obvious outstanding jobs has been the goods shed roof. So, the foam core base had suitable wills sheets fitted, with cutouts for the skylights. Then, following a lot of filling, sanding and scribing slates, the joints start to disapear. Finally, following painting (various mid-dark grey Vallejo acrylics stippled on with a sponge over the grey primer, followed by a wash of Arthonian Camoshade from games workshop), it’s offered up to the buildings. Bargeboards and skylight glazing to follow (the joints in the roof stand out a bit more in this shot, it’s due to a reflection I hope a coat of varnish will dull down). The two 12t vans poses for their ex works shot. It’s intended these are going to be pretty clean, suggesting they’ve been overhauled recently and create a contrast with some of the rattier stock. This also shows my approach to wagon numbers. The ply sided is based on an actual van, which starred in a BTF film about the usage of TOPS on wagonload freight. The marge van is from the correct number sequence according to Roland, however it’s also a habit of mine, on wagons where it’s not based on a actual individual wagon I have the last three digits as a well known RAF squadron (which is how the 21t mineral got ‘617’). Finally, a couple of shots taken of the goods yard area, showing how it’s starting to come together. Rather pleased with this. Owain 9 Link to post Share on other sites More sharing options...
RMweb Gold Corbs Posted October 6, 2020 RMweb Gold Share Posted October 6, 2020 Nice and crowded, just as it should be! 2 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 7, 2020 Author RMweb Gold Share Posted October 7, 2020 9 hours ago, Corbs said: Nice and crowded, just as it should be! Yes, that’s the exact look I’m after! Glad you like it. On that note, the ideas for an extension have come on a bit. It’s still not 100% and the geometry is in best guess territory, because this is being laid out with a set of Hornby 1/4 scale track planning symbols, but here it is. Mid green is the running line, dark brown hidden tracks. Olive green is the shed lines. Black shows where the back scene will sit roughly and light brown is preliminary outlines of buildings. The scenic break will be provided by a semi low relief single track carriage shed built on the unused formation alongside the running line, the bulk of the runnng shed and various other small/temporary buildings (containers, portacabin etc). For anyone who wants to work out where this is, that overbridge is the A683, the area is the field to the west of the formation. Beyond the running shed, the buildings are (front to back) main heavy workshop, carriage shop and boiler/heavy fabrication shop. The siding in front of the workshop is somewhere for the crane to live. In terms of style, the running shed will be a very close relation of the one at Grosmont, the workshop based off a Hornby diesel depot (with an overhead crane in the roof and the ends filled in with corrugated tin, but retaining the side windows, because I want to have fun with the contents), inspired by George Dent’s use of this structure on a couple of dioramas. The rest will be semi low relief corrugated tin, the road into the carriage shed will accommodate a single coach, the boiler shop depends on how the final geometry works out, because the three way point is best described as a guess and that bit of paper needs to be 28mm longer. Now, because this will just (with about 12” to spare) fit in the garage when it’s all set up, the idea is that these two boards will also be a ‘stand alone’ setup, capable of being run on their own. This is something I’ve fancied modelling from the off, so watch this space. Owain 2 Link to post Share on other sites More sharing options...
MattA Posted October 8, 2020 Share Posted October 8, 2020 I never fail to be impressed by your efforts, Owain. It seems that every piece of rolling stock and every inch of permanent way that you touch turns into a work of art! 1 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 8, 2020 Author RMweb Gold Share Posted October 8, 2020 5 hours ago, MattA said: I never fail to be impressed by your efforts, Owain. It seems that every piece of rolling stock and every inch of permanent way that you touch turns into a work of art! Well thank’ee very much! I’ll have to start sticking up some of the bits I’m not quite happy with and aren’t as good, before I start getting a reputation! Anyway, the goods shed, continued. The skylight openings had pieces of acetate inserted and glued in, then framing and glazing bars were added in evergreen styrene sections. The chopper proved invaluable for cutting the glazing bars. Then, the main doorway was tackled. As earlier mentioned, I see the goods shed being used as a shop/cafe, so as part of that I added (using acetate, more evergreen sections and a modern door from a set from Peco) a secondary door and glazed the remained of the main door opening. So, with some barge boards and an initial weathering session (an upcoming job, as soon as the weathering’s finished and the building shell is bedded down, is filling the trench around the walls) here’s a couple of shots of it on the layout. Finally, I’ve fancied one of these Hornby trout ballast hoppers and following an idle google session, found that Model Junction of Bury St. Edmunds (recommended, excellent service) had one remaining in stock, so I splashed out. The first job when it arrived was to correct the angle of the operating handwheels (an irritating little detail that let down an otherwise nice model). However it was still far too clean, so as is my wont it got attacked with washes and the usual games workshop rust paints (Typhus corrosion and Ryza rust). Here it is, coupled to the dogfish (and until it arrived, I didn’t know the trout hoppers were unfitted). Owain 6 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 9, 2020 Author RMweb Gold Share Posted October 9, 2020 On the goods shed, an interior of sorts has been fitted, using pictures from the adverts section of a copy of model rail and an issue of Moorsline (mucho ta to Digitrains for putting up the photos of the interior of their shop in their advert!) (incidentally, if you know the gaffer in the picture back right and the gent using a burning torch behind the gadgie explaining something to a traffic warden, then feel smug) mounted on offcuts of foam core board. Also a spare wagon (slaters?) and various spare second rate figures are added. The pencil lines in the floor are representations of the rails. Then, whilst looking through the adverts, I found one with small versions of the manufactures logos, so these were added above the doors. Also the sliding door gained a bottom track (this is to make filling in round the building easier) and two tiny signs timetables. Finally, here’s the result on the layout (photos taken with the roof off to get some light). Owain 6 3 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 9, 2020 Author RMweb Gold Share Posted October 9, 2020 And the last one for today, I promise! The goods shed has been glued down and the trench round it filled in with modelling clay (this also shows how the door slot added earlier works) The gaps around the end doors were made up with ballast. Then the tarmac was retouched to loose the clay and also create a bit of shading over the whole area. The provendor store was also secured down, the jungle of weeds underneath added with foliage and grass tufts. Other grass tufts were added where weed growth could appear. Rather pleased with how this has come out. Owain 8 3 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 11, 2020 Author RMweb Gold Share Posted October 11, 2020 A bit more, first up two vehicles have been weathered, a corgi Bedford OB finished in a local livery (when I worked in Bowness, if I was really lucky, I’d end up following this from Ings to Staveley (or Kendal if I hit the jackpot) at 30mph on the way home) and a carama Ford transit, (with a tribute to a colleague and friend in the muck on the back doors). Next up, a nice and easy conversion, fitting the red panda under frame to the Bachmann conflat. And until I looked at it, I hadn’t realised the Bachmann underframe has the cylinder and the Morton clutch the wrong way round. Owain 4 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 12, 2020 Author RMweb Gold Share Posted October 12, 2020 As a mate of mine would have put it ’Another flat battery in the car park of life’. Earlier this year I gave the attic a vigorous tidying, one object of which was to find the locos from two earlier modern image layouts, Backbarrow (2002-06) and Teeside Coil (2006-9(ish)) (incidentally, the baseboard frames of Backbarrow survive under Sedbergh). The locos concerned amounted to two 66’s, a 60, a 37 and a trio of Heljan 47’s. As mentioned earlier, an idea is that the railway leases space at Middleton to a spot hire company, so with a mainline connection at Lowgill they can bring locos in off the mainline network and it was wondered if these locos could stand in. Unfortunately, the dreaded mazac rot has attacked the Duffs, with one with a chassis block that’s got a 4mm bend in it one way, a 2mm dip where the belly tanks go, a lot of cracking (so I suspect if I try to straighten it, it’ll disintegrate) and one nose split off the body shell. Another (the DRS example) had a body shell that was nigh on impossible to get off the chassis, however apart from that it seems OK, there’s no major distortion of the chassis, so the idea is to skim the chassis block in the mill (yes, I know that doesn’t stop the rot, but apart from the bodyshell being seriously tight there’s no sign of other issues, and since when I bought it (sometime around 2005) I was DC only and it never saw service on the DCC Teeside Coil (Unlike the banana shaped ‘792, which also wants rewheeling from P4. God knows where the original wheels have gone in the meantime) I don’t know if it’s ever actually had the body shell off in the last 15 years) and then make one decent Duff out of two duff Duffs (sorry, I couldn’t resist...). The third (and the oldest) the RFD example seems fine, so that’s being overhauled and chipped. Owain 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 12, 2020 Author RMweb Gold Share Posted October 12, 2020 And a brief Duff update! There’s three, ‘361 (RFD), ‘792 (EWS) and ‘298 (DRS). Of these, ‘361 has now been overhauled, pickups/wheels cleaned and is ready for a chip to be fitted (probably the elderly lenz silver that was in ‘792). ‘298 will be next after it’s chassis block has been skimmed (I’ve measured it up and I think it’s just a very tight fit in the body shell). ‘792 is probably, in the absence of a new chassis block, becoming a spares donor, having already given up a drive gear to ‘361, also pickups and headlight fittings to ‘298. On the plus side, by some small miracle, I’ve found it’s original wheels, so it may get rebuilt as a motorless towable demic (which would be somehow appropriate, because it was the last (then) EWS 47 I saw in traffic. Owain Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 13, 2020 Author RMweb Gold Share Posted October 13, 2020 (edited) And here’s the rather beaten up 47361, as loaned to the L,S&IRCo., following the failure of 31452 (wheelset and bogie issues or in reality, I got sick of its back-to-back measurements causing shorting in the points). Materials used are MIg washes, games workshop rust paints, humbrol matt yellow and a fibreglass brush. The effect on the cab sides is based on a photo of the loco where the yellow is coming through the grey. The RFD logos are attacked with a fibreglass brush then gently dry brushed with yellow to loose the white base colour that appeared in the red diamonds. The scratches on the other side are entirely fictional, I just wanted to have a play with some effects (I assumed under the grey was BR blue, so added some Hoeth blue paint chips). I’ve also just realised that nameplate isn’t level either. Such is life. 47792 has started to deteriorate as well... Owain Edited October 13, 2020 by Firecracker 6 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 27, 2020 Author RMweb Gold Share Posted October 27, 2020 Right, the latest progress, this time it’s the southbound fiddle yard. Regular readers of this nonsense may remember that the original plan was to use a cassette system. However, as is the way with plans it didn’t survive contact with the enemy, due to how unwealdy a cassette with loco and 4-5 carriages is. Also, the limited space in the garage and the angled approach didn’t help. Whilst up in the attic duff-hunting, the last fragment of an earlier layout, Backbarrow, was unearthed. Now it was decided to scrap this, due to the lack of structural integrity of the remains and it really wasn’t in a decent state. However, this yielded an assortment of track, which was thrown down on the fiddle yard board to see what stuck. Incidentally, due to various factors, mainly the straight approach and the fact that the northbound section sees less variety of traffic, at the moment it’s likely the northbound fiddle yard (on the rare occasions it’s connected) will retain the cassettes. Slowly, ideas started to solidify, with two fixed roads at the front for the shed headshunt and a 2 car siding at the back for the DMU. The two remaining roads will run onto a lifting hinged section, capable of taking a 5 car rake plus loco. The idea of that it being hinged is that it can be easily folded away at the end of a running session, yet should be solid enough to support the weight with no issues. Two cassettes were used to mock up this, (the drill box and tape is there purely as a counter weight whilst the photo is being taken). When out of use, the idea is it’ll fold on top of the baseboard. Some shunting trials showed the idea had legs, so it started to be translated into reality. Because it’s a non-scenic board all the wiring can be on top and the hinges show the approximate location of the lifting section. Apropriately, the jinty and the inspection saloon formed the first train, along with the diner rake. Finally, as part of the trials, the janus trundles southwards with the vac braked ballast hoppers and the queen Mary brake. For those who wonder how this fits with the extension mooted earlier, there is a plan (honest!). It goes roughly as follows. The extension should still happen, however it’s become three boards rather than two. The third board serves as a transition between the extension and the existing layout (minus the southbound fiddleyard), however the idea is that it’ll be possible to operate the station and the shed as two physically separate setups as well. Owain 4 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 29, 2020 Author RMweb Gold Share Posted October 29, 2020 Right, the latest activity has been a testing and development session, beating out bugs in the rolling stock, tweaking the new fiddle yard track and playing with a new phone camera. Here’s some of the results (and a proper backscene, rather than a chunk of expanded polystyrene is creeping up the agenda). Owain 5 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 30, 2020 Author RMweb Gold Share Posted October 30, 2020 And a bit more, the PWay department has come out to play. So first, some moving pictures. Then, some closeups of the wagons and the loco. Owain 9 Link to post Share on other sites More sharing options...
RMweb Gold Corbs Posted October 30, 2020 RMweb Gold Share Posted October 30, 2020 Spot on as always. 2 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 30, 2020 Author RMweb Gold Share Posted October 30, 2020 1 hour ago, Corbs said: Spot on as always. Well, thank you very much! There’s still a lot of little bits to do, (platforms to tidy, point rodding to finish, some more figures on the rear platform (and that’s just what the photos show)), the absence of a back scene needs addressing and there’s a few more mechanical bugs to beat out (on the other hand, ran passenger services in and out 2 dozen times with running round, with no issues or derailments) but I’m getting happier with it (hence, getting the twitch about an extension). Not a bad comeback, if I say so myself. Owain 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted October 31, 2020 Author RMweb Gold Share Posted October 31, 2020 A bit more, back to the Sturgeon seen earlier (intended as the PWay’s rail carrying wagon). It’s been fitted with buffers and kadees. Due to the deep buffer beams, I’ve used NEM pockets. Shunting trials with the Ruston showed it was happy with all the track, crossovers, curves etc. The idea is that this is going to be finished as one of the internal users at Workington steelworks, that were used to carry rails to the docks. So a light blue livery for something different, as seen in Paul Bartlett’s photos here. https://paulbartlett.zenfolio.com/workingtonsteel Owain 5 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted November 8, 2020 Author RMweb Gold Share Posted November 8, 2020 Right, an update (appologies for the delay, my employer requested I return to work this week and do something that passed for useful work in a bad light). Anyway, the sturgeon. It’s been airbrushed in Vallejo blue, details touched in with humbrol and the deck attacked with the usual mix of games workshop paints and Mig washes. Some stripwood dunnage stained with Mig’s Wash for wood was added to the deck. Then some rail, cut into scale 60’ sections (the pleasing rust effect was achieved by accident with Carr’s metal black for steel and whitemetal) Add some ratchet straps from masking tape Finally, moving pictures! Owain 8 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted November 15, 2020 Author RMweb Gold Share Posted November 15, 2020 Right, not much to report this week, most of the weekend disappeared on a testing and development session which solved several issues (such as ‘why does that coach always derail there?’) and confirmed a lot of other work, including the session training the decoder in the little sentinel with the SPROG has born fruit with its slow speed performance. Anyway, here’s another of those moving pictures. Enjoy. Owain 6 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted November 29, 2020 Author RMweb Gold Share Posted November 29, 2020 Again, not much to report, apart from a farce with the Lenz DCC setup. Following that, it looks like a modernisation to a SPROG and (shock, horror) wireless throttles is on the cards! Where will it end? It’ll be things flying backwards in the skies next... Anyway, some parts of the layout have already met a SPROG, especially this Sentinel. Fitted with a Digitrax decoder, it had rather an athletic turn of speed. However, following a spot of tuning, it’s now calmed down considerably and has becom a reliable member of the fleet. Need to decide if it’s getting the runner wagon I had planned for it and maybe renamed. It’s certainly next on the weathering list. Owain 8 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted December 6, 2020 Author RMweb Gold Share Posted December 6, 2020 So,with the repeat lockdown ended, my local reopened. This little pile of goodies followed me home. I’ve fancied a bubble car since Lima released their effort (at the time, other demands on my money prevented it) and I think at the moment if you can afford it, prise open the old wallet and support your local shops. Plus Martin knows me too well and specialises in swift and painless wallet extraction (from customers, naturally). The LMS compartment brake third was reduced by a tenner and following a bit of research I’ve justified it with a) there’s two of the 9 comp thirds at Keighley (not sure if they’re in traffic), b) two and a bit comp brake third body shells survive in Scotland, so it’s possible and c) did I mention it was a tenner off? First up, the DMU. Opened up, fitted with a Zimo decoder and the Bachman passengers (just needs a driver or two). Introduced to the SPROG and the decoder addressed to my standard of the last 2 digits of the number, it comes out for a gentle trundle and poses with the 101. Then, the coach. Dirtied up with MIG washes, it’s gone into the scratch rake with another two maroon mk1’s. It runs into Sedbergh behind the class 15, passing a DMU lashup in the second platform (the lashupis posed, I need to tweak the decoders to get them to run in multiple). Finally, a friend and her hound have appeared o;the layout, care of Bachman, Noch and a steady hand with a 10/0 brush to tweak the hounds markings and add a harness. Owain 5 1 Link to post Share on other sites More sharing options...
RMweb Gold Firecracker Posted December 6, 2020 Author RMweb Gold Share Posted December 6, 2020 And just for the hell of it, here’s another of those moving pictures. Enjoy. Owain 4 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now