jamespetts Posted March 26, 2019 Share Posted March 26, 2019 A class 121 DTS would certainly be welcome - nothing to stop them from doing both at the same time, of course: the class 122 was, after all, released at around the same time as the 121. Link to post Share on other sites More sharing options...
Grimly Feendish Posted March 27, 2019 Author Share Posted March 27, 2019 (edited) Next installment... Here is the end plug added and the roof and joints filled. And here are the DMBS and TC getting ready for priming. The TC ends are masked because I want to keep the factory printing if I can. At this point a couple of things were dawning on me. First, I wasn't happy with the way the etched sides looked. Nothing to do with the etches themselves, everything to do with the way I stuck them on. You can see the huge gap between the etch and the roof. Also the way the etch was stuck to the side was not robust. The cyano could not tolerate any bending of the plastic side. So I removed the sides, rubbed them down again and reapplied, paying more attention to the fit and using a thinner cyano. This resulted in a better fit, but is still not robust. At least now I am careful in handling it and it's surviving so far. I know I have to do something with the roof of the TC too. Second, on the DBMS I managed to get the roof profile reasonably acurate, but there is an unsightly gap between the two roof sections. I'm hoping that with judicious weathering it might not be too noticeable. You might get an idea from this photo, which shows the roof alongside the body after priming. I decided on a different approach for converting the second 121. I would slice off the cab and put on an end plug as before, but would keep the roof in one piece and build up the profile at that end with filler, as shown below. I am much happier with this approach. The two are shown together below. Both have had a few rounds of filling and rubbing down since this shot. I don't have pics for that yet. I'm sure you have noticed that as it stands, I'll have 2 DMBSs and 0 DMS. Since I struggled with the etched sides I'm tempted to keep it that way. I think I would rather have an incorrect consist than risk the look of me bodging the etched DMS sides on. I am not convinced I can get the joint between the etched sides and the Dapol cab looking decent. Anyhow, that brings us up to date. It'll be a while before I can get back to some modelling, but I'll post when I have something to show. Cheers, John. Edited March 27, 2019 by Grimly Feendish 1 Link to post Share on other sites More sharing options...
RMweb Premium PaulCheffus Posted March 27, 2019 RMweb Premium Share Posted March 27, 2019 Hi When I attach etched sides to plastic coaches I tend to use Araldite Rapid as this gives a little flexibility and also allows fine adjustment before it dries. Cheers Paul 1 Link to post Share on other sites More sharing options...
1977joey Posted September 2, 2019 Share Posted September 2, 2019 Just found this thread. I very much want an N gauge Class 116 or 117 unit in N, it's been on my wish list for years! Can't believe Bachmann (after it being a most wanted model in N for a good couple of years running) are only doing it in OO so far. I'm also hoping Dapol fill the gap with one of these units. Looking forward to seeing the progress on this model your doing john.... All the best, Mark Link to post Share on other sites More sharing options...
Grimly Feendish Posted September 8, 2019 Author Share Posted September 8, 2019 Hi Mark, unfortunately I've had to put this on hold for a while. We moved house and will be moving again in a few weeks, It will be a while until I can get back to modelling Cheers, John. 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now