Mark90 Posted July 26, 2020 Share Posted July 26, 2020 5 hours ago, richard.h said: Thanks very much for the info guys it's much appreciated and will be looked into. It's amazing how things change so quickly with this virus, I was just thinking it has been 20+ years since I was in that part of the country and now with the quarantine news it is going to another year, the holiday is cancelled until 2021. Rubbish luck with the cancellation. Hopefully things will be better in 2021! 1 Link to post Share on other sites More sharing options...
richard.h Posted July 28, 2020 Author Share Posted July 28, 2020 Kadee Shuffle I really like the Kadee coupling system and the advantages it brings to a layout but I wanted the uncoupling magnets to be invisible where possible so as not to spoil the track appearance. To achieve this I experimented with different types an strengths of magnets. The first type, rod magnets worked OK on Locos and Coaches but the power was too concentrated for light weight wagons which the magnets tended to tip over so I used these in the Station for mainline trains, the advantage being that they could be fitted after tracklaying and are invisible with a light covering of ballast. The second type, square plate magnets proved the answer for shunting trucks as they had a larger but less concentrated magnetic field so they can be set lower into the track ballast but they have to be fitted before the track is laid. There is a demo video to follow this once I get it loaded in. 2 Link to post Share on other sites More sharing options...
richard.h Posted July 28, 2020 Author Share Posted July 28, 2020 Kadee Shuffle with Wonky Uprights I filmed this video with my new camera which can record in High Definition and Dolby Sound, (that's progress!) unfortunately I didn't realise until afterwards that in this mode it uses a compression system which results in fine vertical edges becoming blurred when not in central focus, see the signal bracket and lamp posts. So I'm afraid it will be back to shooting in its MP-4 mode for indoor model railway videos in future. 5 Link to post Share on other sites More sharing options...
richard.h Posted August 1, 2020 Author Share Posted August 1, 2020 (edited) To compliment the video here are some photos of the J11 shunting. I have recently had a lot of my original lighting starting to fail so rather than just replace them I thought I would investigate using LED lighting strips instead. The brightness is fully adjustable so the you can simulate different times of day and create shadows. You can also gradually change from cold white to warm colour light or any mix in between which gives a large range of effects not just for photography but to create a different atmosphere for the layout and these two photos show the extremes of the range. Edited August 4, 2020 by richard.h Update 4 Link to post Share on other sites More sharing options...
richard.h Posted August 4, 2020 Author Share Posted August 4, 2020 There has always been a corner of the layout devoted to Mr Dibnah's Traction Engine Workshop and business has been good lately so he has gone and bought a new Land Rover. It's a bit modern for the time period but weathered down a bit it doesn't look too out of place. 7 Link to post Share on other sites More sharing options...
richard.h Posted August 8, 2020 Author Share Posted August 8, 2020 Over the past few months I have been buying Coke Wagons, 2-3 at a time in order to build up a complete train. The weathering starts off with the same pattern distressing the lettering on older type wagons using a fibre glass pencil and painting in some of the raves to simulate repaired sections. The next stage is to spray the chassis with frame dirt and the bodies with dirty black. Then I bring in the variations by using a blend of different colours each time, mud, oil, grease, rust etc. This particular batch have been treated with dark rust to the solebar and halfway up the body sides which is typically shown on old photos. When all the different wagons are then put together you have a set where no two wagons are the same.. 6 1 Link to post Share on other sites More sharing options...
richard.h Posted August 13, 2020 Author Share Posted August 13, 2020 In the few years since I have been fitting sound systems to my locos there have been dramatic improvements in speaker technology which means of course big improvements in sound quality. Since I don't have a workshop with milling machinery I have always been limited by having to install a speaker that would fit in the space available so for my latest acquisition there was just enough room to fit a Boom-Box speaker. So here is the Limited Edition Deltic Prototype (East Coast Mainline Version) with sound system installed at factory settings, you can turn it down! 1 Link to post Share on other sites More sharing options...
richard.h Posted August 16, 2020 Author Share Posted August 16, 2020 To compliment the Deltic Video here are some photos of the Loco in action which has now been weathered in order to tone down the blue plastic look and help it blend in with my other Locos. The bodywork was first toned down with Lifecolor Acrylics, Frame Dirt to the lower parts then Weathered Black and Dirty Black to the roof panels in order to give some variation in the colouring. Then the chassis was treated with AK enamels, fuel stains to the fuel tanks and grease and oil stains to the bogies. Now I think it looks better as although all the photos I can find show it as been kept in good condition it certainly was not immaculate! 7 Link to post Share on other sites More sharing options...
richard.h Posted August 20, 2020 Author Share Posted August 20, 2020 Shapeways Couplings Apart from local goods trains most of my freight stock is in fixed sets which are kept in cassettes when not in use so I have been looking for more authentic couplings to use on the sets. After seeing some details of the new 'Shapeways ' couplings I thought they might be worth a try to see how they performed. These are the two types I ordered complete with the box they came in, no wonder the postage was a bit expensive. I ordered two types for NEM pockets, straight and stepped in the shortest length available, 18mm, in order to keep the wagons as close together as possible, so here are the two types with some test painting to determine what colours would look best. The stepped type look better so I made up a train in sets of four wagons permanently coupled together with a kadee or tension lock at either end. If they do prove successful I think it might look better with some of the new magnetic couplings replacing the conventional ones. So far they are working well, they negotiate the sharpest curves without problem and have not pulled apart or broken on my normal train length of 24 trucks+ although a bit more testing is needed before buying any more. 6 1 Link to post Share on other sites More sharing options...
richard.h Posted August 25, 2020 Author Share Posted August 25, 2020 Continuing the trials with the new couplings I have been fitting them to different types of stock and I thought that the sternest test would be on longer heavier wagons. So here they are on a train of bolster wagons and long wheelbase plate wagons with most of them carrying loads. They are also look more effective on these wagons as they are much more visible. After an extended running session they behaved perfectly so I think that they can now be safely fitted to any type of goods wagon. 5 Link to post Share on other sites More sharing options...
richard.h Posted August 30, 2020 Author Share Posted August 30, 2020 Today we have a few photos of The Wolf of Badenoch as it makes its way towards Byford. This is a DJH kit with an extra capacitor wired into the decoder for "Stay-Alive" as I wanted to ensure good performance because the kit as built only has pickups on three driving wheels and the opposing three tender wheels 4 Link to post Share on other sites More sharing options...
richard.h Posted September 4, 2020 Author Share Posted September 4, 2020 Here is a video I made showing typical activity seen in a morning down at the local Village Station. 2 Link to post Share on other sites More sharing options...
richard.h Posted September 8, 2020 Author Share Posted September 8, 2020 (edited) Loco Shed Rebuild My original six road engine shed is starting to show its age now and is one of the layout buildings marked down for an upgrade, Pacific Locos don't quite fit in as can be seen from the photo and there is no room for internal fittings or lighting which is something I would really like to add, With this in mind I thought that I would try building one of the Laser Cut Kits that have become available in the last few years. The first thing to do before building commenced was to get the basic colour scheme acceptable. The brickwork detail is extremely fine so after some experimentation I found that the best solution was a first wash with sand colour paint. This was followed by a couple of coats of very light dry brushed red brick paint. So that's the base colour sorted, later on I can add textures and weathering. So now to paint and assemble the rest of the body shell and in the meantime I need to source tools for a workshop and suitable lighting to fit inside. Edited September 8, 2020 by richard.h correction 3 Link to post Share on other sites More sharing options...
richard.h Posted September 13, 2020 Author Share Posted September 13, 2020 I have just spent the last few days progressing with the Shed. Firstly all the exterior walls were completed. Painted and Textured. Next step was to fit the sides together and then add the roof joists, these were painted in weathered wood although I don't know in real life if they used wood in a Steam Shed, maybe metal would be safer. Next step fit the Roof and start the tiling (that will keep me occupied for a few days while the lighting turns up). Then put it in place to see if we are on the right track! as I still have to build a second unit to make a six lane shed plus workshop. 6 Link to post Share on other sites More sharing options...
richard.h Posted September 19, 2020 Author Share Posted September 19, 2020 More progress, this week I glued a piece of copperclad strip out of sight in the roof trusses to form a distribution busbar From there I can add lights wherever they are needed by just tapping onto it. Next step was to complete the first shed by finishing and painting the roof and vents. And now we make a start on constructing the second shed which will require some surgery as the tracks are already in place so the building will have to be trimmed down to align with these. 4 Link to post Share on other sites More sharing options...
richard.h Posted September 27, 2020 Author Share Posted September 27, 2020 I finished off the main shed building this week. Then started on the weathering, the roof vents and main building, particularly around the entrance were airbrushed with burned and dirty blacks . The roof tiles were treated with Tensocrom soot colour to give a rain streaked effect. The lighting was finished off and connected in. Sharp eyed viewers will notice a gap in the left hand side wall, I am currently constructing a workshop which will fit down that side once all the bits arrive so there's still a bit more to do. 7 Link to post Share on other sites More sharing options...
richard.h Posted October 4, 2020 Author Share Posted October 4, 2020 As a break from Shed Building here are some photos of the latest loco to join the fleet a 9F Here being turned ready for duty. And now in service on a Coke Train as it clears Low Fell tunnel and the runs through town. 4 Link to post Share on other sites More sharing options...
richard.h Posted October 8, 2020 Author Share Posted October 8, 2020 Here are a couple more photos of the 9F as it meets its stablemate. And then clanks trough the Station. 3 Link to post Share on other sites More sharing options...
richard.h Posted October 8, 2020 Author Share Posted October 8, 2020 And to finish off here is a video showing the sound installation of the loco plus a short running session 1 Link to post Share on other sites More sharing options...
richard.h Posted October 11, 2020 Author Share Posted October 11, 2020 More bits arrived during the week so I was able to finish off my workshop extension to the Engine Shed. I just need to fit a couple of lights in it otherwise it will be difficult to see once it's in place. The workshop fits against the shed and the roof needs another coat of paint to match the main shed roof, but that's on order 5 Link to post Share on other sites More sharing options...
richard.h Posted October 15, 2020 Author Share Posted October 15, 2020 Foreigners on The Line (Locos not People) I recently had the unenviable task of being asked to clear out a complete model railway layout and collection, I hadn't seen it before and was not able to test anything beforehand so I just bought everything on trust. So, over the next few weeks I shall be testing the items to see what runs, what I can use on my layout and what is saleable. The first items to be inspected and tried on my layout was a Heljan Railbus And a Class 20 Diesel After a good clean and service they both performed well. So, that's a good start and now on to the next ones. 4 1 Link to post Share on other sites More sharing options...
richard.h Posted October 19, 2020 Author Share Posted October 19, 2020 Another couple of foreigners. Royal Scot 'The Royal Air Force' pulls into Oxenholme Station. And a Class 16 Diesel runs through with a short goods train. In real life these were apparently very poor runners. I have bought a lot of the 'Zen' decoders in the past because they have a Stay Alive function. The capacitor supplied with them is not very effective but it easy to upgrade them, so in this case I fitted a 1000uf capacitor and the loco now performs perfectly running even at speed step 1 without hesitation over the point work. 6 Link to post Share on other sites More sharing options...
richard.h Posted October 23, 2020 Author Share Posted October 23, 2020 Another stranger in town is this Class 42 Zenith. Seen here entering the Depot for refueling This loco was a bit of a challenge, it had been badly weathered with brown streaks and then scratched by someone trying to remove them. I managed to remove most of the brown paint but couldn't do much about the scratches so I had to give it a heavy weathering with frame dirt and carriage grime then a light coating of soot to tone everything down. 3 Link to post Share on other sites More sharing options...
richard.h Posted October 26, 2020 Author Share Posted October 26, 2020 The layout features a small outdoor market area and this is now my third attempt to build it. The previous attempts have failed because after time and due to a combination of glue, paint and heat the base has warped. So this time I tried a different approach and used a solid base with the wood supplied for laser-cut kits. For the shoppers safety I added bollards made from the spare extension pieces of street lights plus chains. At one time I thought that I would never bother painting any more people, too much trouble when there are so many excellent ready painted one around, but the advent of the 3d printed period figures changed my mind, they are just so good. So a set was ordered to populate the Market Place. And now the completed assembly is placed back in position and hopefully this time it won't warp. 5 1 Link to post Share on other sites More sharing options...
richard.h Posted November 2, 2020 Author Share Posted November 2, 2020 This foreigner has been converted, it's a Class 08 Diesel which is good runner but it was in the wrong livery (BR Blue). So it was cleaned up and the body was resprayed in green and the chassis with dirty black then the transfers were added. Now with a touch more weathering to the roof, body and motion. She is ready for duty in the Goods Yard. 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now