Killian keane Posted March 1, 2019 Share Posted March 1, 2019 Hello chappies, to avoid cluttering up elsewhere, heres a dedicated thread, models wo far consist of seaford, built 1859, rebuilt early 1870s (?) scrapped 1878 and 97s, built Jones & potts 1845 as a tender engine, rebuilt 1852, scrapped 1860 7 1 Link to post Share on other sites More sharing options...
Edwardian Posted March 1, 2019 Share Posted March 1, 2019 Hurrah! Bring on the Victorian locomotives. 1 3 Link to post Share on other sites More sharing options...
Killian keane Posted March 2, 2019 Author Share Posted March 2, 2019 (edited) heres something Ive been working on purely for myself, patterns for the tender and driving wheels for Fire Queen in 16mm scale, drawings for this loco are few and far between which is a shame because she would make a legitimate 00 gauge model, maybe some day Edited March 2, 2019 by Killian keane 5 Link to post Share on other sites More sharing options...
Killian keane Posted March 5, 2019 Author Share Posted March 5, 2019 (edited) If anyone has drawings for this nlr Sharp Stewart I think it would make a nice companion to the millwall extension railway manning wardle already available and L49s outside cylinder 2-2-2wt in a hypothetical Victorian London micro Edited March 12, 2019 by Killian keane 8 1 Link to post Share on other sites More sharing options...
sem34090 Posted March 5, 2019 Share Posted March 5, 2019 I shall see if I can get anywhere with that for you. 1 1 Link to post Share on other sites More sharing options...
Edwardian Posted March 5, 2019 Share Posted March 5, 2019 I had planned a GE/Blackwall/Millwall Extn themed micro. A capriccio, if one likes. Could be tempted to revive the idea! Who wouldn't want one of these? The practicalities of motorising again concern me. It would also have mire appeal if suitable stock could also be printed. 1 Link to post Share on other sites More sharing options...
sem34090 Posted March 5, 2019 Share Posted March 5, 2019 Well, I keep returning to the idea of modelling Blackwall, and given I've been told that I may soon be heavily involved with the NLRHS I guess I ought to consider an NLR layout at some stage!!! 1 Link to post Share on other sites More sharing options...
RMweb Gold Regularity Posted March 5, 2019 RMweb Gold Share Posted March 5, 2019 5 hours ago, Killian keane said: If anyone has drawings for this nlr beyer peacock I think it would make a nice companion to the millwall extension railway manning wardle already available and L49s outside cylinder 2-2-2wt in a hypothetical Victorian London micro I think I might very well be in love. 1 1 3 Link to post Share on other sites More sharing options...
Edwardian Posted March 5, 2019 Share Posted March 5, 2019 1 hour ago, Regularity said: I think I might very well be in love. You wait til you start fancying Large Scotsmen. 2 Link to post Share on other sites More sharing options...
RMweb Gold Regularity Posted March 5, 2019 RMweb Gold Share Posted March 5, 2019 2 hours ago, Edwardian said: You wait til you start fancying Large Scotsmen. Already fallen for the small ones... 1 1 1 1 Link to post Share on other sites More sharing options...
Caley Jim Posted March 5, 2019 Share Posted March 5, 2019 6 hours ago, Edwardian said: You wait til you start fancying Large Scotsmen. Ah'm sayin' nuthin'. (and keeping a low profile) Jim 4 Link to post Share on other sites More sharing options...
Killian keane Posted March 12, 2019 Author Share Posted March 12, 2019 (edited) I'm working on a Thwaites & Carbutt 0-6-0 with a gothic firebox as owned by Mr Boulton (4 examples, his Wellington, Nelson, Hercules and Mountaineer) if anyone has any idea what the smokebox door was like please do let me know, sorry about the prototype image, it came from evilbay hence the nasty watermark, Im trying to stay as loyal to the drawings as possible, but my logic tells me the wood lagging might have covered the full sides of the firebox, what do others think? I've just tonight released the chimney for Seaford, with the whole loco soon to follow, though I wouldn't advise ordering one until I know the design doesn't need altering https://www.shapeways.com/product/H4VLSQPJK/seaford-chimney?optionId=90247232&key=0f98ee1c1b6e82f01019d5d2dee64ff8&li=shop-inventory Edited March 12, 2019 by Killian keane 8 2 Link to post Share on other sites More sharing options...
Edwardian Posted March 12, 2019 Share Posted March 12, 2019 Both look really great. That 0-6-0 looks just the sort of thing the West Norfolk Minerals Railway would have run. 1 1 Link to post Share on other sites More sharing options...
Killian keane Posted March 16, 2019 Author Share Posted March 16, 2019 On the drawing board today, an 1853 Vulcan 0-4-2 for the Shrewsbury & Hereford Railway 11 Link to post Share on other sites More sharing options...
Killian keane Posted March 23, 2019 Author Share Posted March 23, 2019 Here's what I've come up with for Seafords chassis, the front two axles are fixed and the rear one simply goes along for the ride, essentially she's a 2-2-0 with cosmetic trailing wheels, how well this system will work we shall find out, also just released a 009 clay wagon 5 Link to post Share on other sites More sharing options...
Killian keane Posted April 1, 2019 Author Share Posted April 1, 2019 (edited) Queen of the forest is nearing completion, I will be doing alternative saddle tanks and chimneys to represent its later guise as Ant, the only hard part left for the modeller being the extravagant lining! Edited April 1, 2019 by Killian keane 7 3 Link to post Share on other sites More sharing options...
Edwardian Posted April 2, 2019 Share Posted April 2, 2019 More brilliant work, however, the Thwaites and Carbutt 0-6-0 particularly appeals, as I feel I could have a use for it on the Norfolk Minerals. On 12/03/2019 at 14:57, Killian keane said: I'm working on a Thwaites & Carbutt 0-6-0 with a gothic firebox as owned by Mr Boulton (4 examples, his Wellington, Nelson, Hercules and Mountaineer) if anyone has any idea what the smokebox door was like please do let me know, sorry about the prototype image, it came from evilbay hence the nasty watermark, Im trying to stay as loyal to the drawings as possible, but my logic tells me the wood lagging might have covered the full sides of the firebox, what do others think? I've just tonight released the chimney for Seaford, with the whole loco soon to follow, though I wouldn't advise ordering one until I know the design doesn't need altering https://www.shapeways.com/product/H4VLSQPJK/seaford-chimney?optionId=90247232&key=0f98ee1c1b6e82f01019d5d2dee64ff8&li=shop-inventory My first question, then, is whether these designs will be for sale? If so, a number of questions, growing in impertinence suggest themselves: - Where and in what materials will you print it? I think I can offer you an SLA smooth resin print if you have not access to a Photon machine or similar. - Will you be drawing the loco chassis and the tender? - The wheels look to be 4'6", so pretty easy to come by, but the style is distinct, will you, therefore, print wheel centres to match the prototype? - The wheelbase looks to be 7' 1/8" + 6' 6". What would you suggest concerning coupling rods? - There is not a lot of room under the bonnet in 4mil. How would you plan to motorise? A motor geared to the centre wheels and slanting back into the firebox would seem an option. Would you specify a motor and gears and print a motor mount to suit? - Body details: Will you include the footplate-mounted springs behind the splashers? Will you include the footplate-mounted sandboxes? There are 3 features on the fooplate between the splashers Will you include the cut-out at the rear of the cab side sheet? I do not think you have the top of the hay stack fire box quite right, if you can possibly forgive me for saying so. I assume that you are working from the Locomotive Magazine drawing published in Mike Sharman/Oakwood Press volume? Apologies for the rude intensity of my interest in this one. If I find any clue as to the smoke-box door arrangement, I'll let you know. Also, I don't know now to interpret the square form forward of the smoke-box. Link to post Share on other sites More sharing options...
Killian keane Posted April 2, 2019 Author Share Posted April 2, 2019 (edited) 1 hour ago, Edwardian said: More brilliant work, however, the Thwaites and Carbutt 0-6-0 particularly appeals, as I feel I could have a use for it on the Norfolk Minerals. My first question, then, is whether these designs will be for sale? If so, a number of questions, growing in impertinence suggest themselves: - Where and in what materials will you print it? I think I can offer you an SLA smooth resin print if you have not access to a Photon machine or similar. - Will you be drawing the loco chassis and the tender? - The wheels look to be 4'6", so pretty easy to come by, but the style is distinct, will you, therefore, print wheel centres to match the prototype? - The wheelbase looks to be 7' 1/8" + 6' 6". What would you suggest concerning coupling rods? - There is not a lot of room under the bonnet in 4mil. How would you plan to motorise? A motor geared to the centre wheels and slanting back into the firebox would seem an option. Would you specify a motor and gears and print a motor mount to suit? - Body details: Will you include the footplate-mounted springs behind the splashers? Will you include the footplate-mounted sandboxes? There are 3 features on the fooplate between the splashers Will you include the cut-out at the rear of the cab side sheet? I do not think you have the top of the hay stack fire box quite right, if you can possibly forgive me for saying so. I assume that you are working from the Locomotive Magazine drawing published in Mike Sharman/Oakwood Press volume? Apologies for the rude intensity of my interest in this one. If I find any clue as to the smoke-box door arrangement, I'll let you know. Also, I don't know now to interpret the square form forward of the smoke-box. Neither rude nor intense Mr Edwardian sir! to answer the questions at hand yes the designs will all be for sale in the relatively near future (I do not like to set deadlines though I've committed to so many as to warrant not starting on any more until the present crop are out!) The prints will be done on a resin printer, or failing that (unlikely) shapeways fine detail plastic the chassis and tender will be done in due course, seeing your interest in the T&C goods that's moved up on the queue the wheels as you say are of a special pattern and centres will be printed to fit commercial 4'6" tyres It is my intention to print rods to suit the wheelbase, pending suitability of the material, Mr Turbosnail of this parish seems to have done so successfully for his rather nice sharpie saddle tank the idea for motorisation is to have the motor mounted either vertically or slanted in the firebox driving onto the middle or rear axle, I cant recommend a motor as of yet simply because I haven't built a prototype(!) regarding the body yes there will be springs behind the splashers (I despise modelling springs more than anything else!) the sandboxes will be present the render you see there is early and largely incomplete I believe the three features between the splashers could be boiler mounting brackets but Im not sure, in any case I will do my best to make the most accurate possible model I can of these locos from the one drawing and one photo I have, the cut out at the rear of the cab sidesheet is not present on the image shown again purely because its at an early stage in that image and will be present on the final model, and finally yes I agree about the firebox top, I'm far from satisfied with it myself (this is the second attempt), the drawings are indeed the old Oakwood press ones, and between these and that photo are the only illustration of this class that I know to exist, thanks for the interest Edited April 2, 2019 by Killian keane 3 Link to post Share on other sites More sharing options...
Edwardian Posted April 2, 2019 Share Posted April 2, 2019 1 hour ago, Killian keane said: Neither rude nor intense Mr Edwardian sir! to answer the questions at hand yes the designs will all be for sale in the relatively near future (I do not like to set deadlines though I've committed to so many as to warrant not starting on any more until the present crop are out!) The prints will be done on a resin printer, or failing that (unlikely) shapeways fine detail plastic the chassis and tender will be done in due course, seeing your interest in the T&C goods that's moved up on the queue the wheels as you say are of a special pattern and centres will be printed to fit commercial 4'6" tyres It is my intention to print rods to suit the wheelbase, pending suitability of the material, Mr Turbosnail of this parish seems to have done so successfully for his rather nice sharpie saddle tank the idea for motorisation is to have the motor mounted either vertically or slanted in the firebox driving onto the middle or rear axle, I cant recommend a motor as of yet simply because I haven't built a prototype(!) regarding the body yes there will be springs behind the splashers (I despise modelling springs more than anything else!) the sandboxes will be present the render you see there is early and largely incomplete I believe the three features between the splashers could be boiler mounting brackets but Im not sure, in any case I will do my best to make the most accurate possible model I can of these locos from the one drawing and one photo I have, the cut out at the rear of the cab sidesheet is not present on the image shown again purely because its at an early stage in that image and will be present on the final model, and finally yes I agree about the firebox top, I'm far from satisfied with it myself (this is the second attempt), the drawings are indeed the old Oakwood press ones, and between these and that photo are the only illustration of this class that I know to exist, thanks for the interest Thank you, that is all very good news from my perspective. I will await developments with interest! 1 Link to post Share on other sites More sharing options...
RMweb Gold Joseph_Pestell Posted April 2, 2019 RMweb Gold Share Posted April 2, 2019 (edited) 3 hours ago, Edwardian said: More brilliant work, however, the Thwaites and Carbutt 0-6-0 particularly appeals, as I feel I could have a use for it on the Norfolk Minerals. My first question, then, is whether these designs will be for sale? If so, a number of questions, growing in impertinence suggest themselves: - Where and in what materials will you print it? I think I can offer you an SLA smooth resin print if you have not access to a Photon machine or similar. - Will you be drawing the loco chassis and the tender? - The wheels look to be 4'6", so pretty easy to come by, but the style is distinct, will you, therefore, print wheel centres to match the prototype? - The wheelbase looks to be 7' 1/8" + 6' 6". What would you suggest concerning coupling rods? - There is not a lot of room under the bonnet in 4mil. How would you plan to motorise? A motor geared to the centre wheels and slanting back into the firebox would seem an option. Would you specify a motor and gears and print a motor mount to suit? - Body details: Will you include the footplate-mounted springs behind the splashers? Will you include the footplate-mounted sandboxes? There are 3 features on the fooplate between the splashers Will you include the cut-out at the rear of the cab side sheet? I do not think you have the top of the hay stack fire box quite right, if you can possibly forgive me for saying so. I assume that you are working from the Locomotive Magazine drawing published in Mike Sharman/Oakwood Press volume? Apologies for the rude intensity of my interest in this one. If I find any clue as to the smoke-box door arrangement, I'll let you know. Also, I don't know now to interpret the square form forward of the smoke-box. What a characterful loco! How ironic that a modern technology is making it possible to make models from an earlier era than previously. To my eyes, looking at the photo, the firebox is not a straight-sided cuboid. It has a bit of a curve to each face. Also, from the photo, the horizontal piece of timber at the top of the firebox cladding protudes further than the vertical staves. Edited April 2, 2019 by Joseph_Pestell 1 Link to post Share on other sites More sharing options...
TurboSnail Posted April 2, 2019 Share Posted April 2, 2019 3 hours ago, Killian keane said: The wheels as you say are of a special pattern and centres will be printed to fit commercial 4'6" tyres It is my intention to print rods to suit the wheelbase, pending suitability of the material, Mr Turbosnail of this parish seems to have done so successfully for his rather nice sharpie saddle tank I've printed wheel centres for my Neilson 2-2-2T and that works fine as long as you can turn them down slightly by holding the axle in a drill and sanding the edge to get it perfectly round. Sorry to throw a small spanner in the works, but I'd be a little more cautious with conrods - I've managed to make them work on a couple of 0-4-0 chassis with a some fettling, rebuilding and occasional coarse language. The only 0-6-0 ones I've tried have never worked, despite many reprints, fiddling, fettling and a lot of coarse language! If you are going to go down that route, I'd suggest driving the central wheels and having split conrods, so you essentially have two 0-4-0 chassis sharing the driving axle. I think that will save a lot of sanity... 3 Link to post Share on other sites More sharing options...
Edwardian Posted April 2, 2019 Share Posted April 2, 2019 1 hour ago, TurboSnail said: I've printed wheel centres for my Neilson 2-2-2T and that works fine as long as you can turn them down slightly by holding the axle in a drill and sanding the edge to get it perfectly round. Sorry to throw a small spanner in the works, but I'd be a little more cautious with conrods - I've managed to make them work on a couple of 0-4-0 chassis with a some fettling, rebuilding and occasional coarse language. The only 0-6-0 ones I've tried have never worked, despite many reprints, fiddling, fettling and a lot of coarse language! If you are going to go down that route, I'd suggest driving the central wheels and having split conrods, so you essentially have two 0-4-0 chassis sharing the driving axle. I think that will save a lot of sanity... Follow the prototype in terms of splitting the coupling rods? Can one commission bespoke rods? I think here also of Derwent Link to post Share on other sites More sharing options...
TurboSnail Posted April 2, 2019 Share Posted April 2, 2019 24 minutes ago, Edwardian said: Follow the prototype in terms of splitting the coupling rods? Can one commission bespoke rods? I think here also of Derwent If you're referring to bespoke printed rods, it's difficult to get the dimensions right if you're using a different printer due to the setup being slightly different. What I did for my F class test model was print 4 sets, each 0.1mm longer than the last and just used the ones that fitted. I'm sure you could commission them (I'd happily draw some up for free, it's a very small job) but you'd need to find someone who could print them for you. Metal rods would be much better if the builder has the skill/equipment to do it (or knows someone who does), as the printed ones are not particularly stiff, which doesn't help with the alignment. They work, but you have to get your chassis setup spot on. 1 1 Link to post Share on other sites More sharing options...
Edwardian Posted April 2, 2019 Share Posted April 2, 2019 Ideally, I'd go for metal Link to post Share on other sites More sharing options...
Killian keane Posted April 16, 2019 Author Share Posted April 16, 2019 the Thwaites 0-6-0 is 80% done, anybody got the inside diameter of a 4'6" tyre in 00 handy? 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now