richbrummitt Posted November 5, 2019 Share Posted November 5, 2019 I've desaturated the image to save some work on making an easy comparison although there is still a little colour difference. What I think I'm seeing is the WS are a little larger in size and there is nothing much to choose between the others, sizewise. Link to post Share on other sites More sharing options...
justin1985 Posted November 5, 2019 Author Share Posted November 5, 2019 Interesting idea for comparison @richbrummitt ! I'd actually say the Attwood product is nicest to work with - in that the grains seem the heaviest, so easiest to work into place. I've messaged them to ask which of their colour ranges might be most suitable for NE Scotland. Given that the proprietor seems very knowledgeable about geology, that seemed a better bet than trying to judge from ropey photos taken in dark exhibition halls. I am impressed with the Polak product as well though. I think the one I tried here might be a good bet for my East Anglian projects. J Link to post Share on other sites More sharing options...
bécasse Posted November 9, 2019 Share Posted November 9, 2019 This issue interested me because I was looking for very fine ballast material to use in a 4mm situation where the prototype would have used, at best, ash and clinker. For "proper" ballast I was already using what may be the Woodland Scenics' N gauge fine ballast (the jar is unlabelled but the contents look identical). However, today at an exhibition in Luxembourg I came across some real possibilities. The first, readily obtainable in the UK, is Noch 09376 Gleisschotter dunkelgrau (ballast dark grey) which is described as being for HO and TT scales but is certainly very fine; here it costs € 2,29 for 250 gm. The other, in a 450 ml plastic jar costing € 5,00, was completely new to me and is described as Gleisschotter Basalt dunkelgrau (ballast basalt dark grey) for N and T gauges; it is sold by a German company called tams elektronik and appears as fine as the Noch product if not finer and is slightly browner in colour (almost a peat colour in fact). This company actually sells quite a range of similar products and their website (only in German) can be found at https://tams-online.de/epages/642f1858-c39b-4b7d-af86-f6a1feaca0e4.sf/de_DE/?ObjectPath=/Shops/642f1858-c39b-4b7d-af86-f6a1feaca0e4/Categories/Produkte/Schotter . 1 2 Link to post Share on other sites More sharing options...
RMweb Gold TomE Posted November 19, 2019 RMweb Gold Share Posted November 19, 2019 On 04/11/2019 at 23:05, justin1985 said: Perhaps controversially, given how popular the Treemendus Normandy Earth powder seems to be with many 2mm modellers, I didn't actually find it that great to use and I'm not that convinced by the result. There seems to be quite a lot of variation in size within the earth powder, including a lot of actual dust - I found it very difficult to smooth into shape. It also feels actually too smooth for "real" ballast - but ideal for slightly overgrown or finer areas like neglected sidings and cess paths. Hi Justin. Hmm, that looks very different to the NEP that I used on Ropley! In fact it looks more like their Lineside Ash product in the photos. I wonder if they've changed the material they use..... Tom. Link to post Share on other sites More sharing options...
justin1985 Posted November 19, 2019 Author Share Posted November 19, 2019 4 hours ago, TomE said: Hmm, that looks very different to the NEP that I used on Ropley! In fact it looks more like their Lineside Ash product in the photos. I wonder if they've changed the material they use..... Tom. Hmmm. I'm wondering whether the bag had settled out dramatically, or something. I'll have another experiment before committing. I also found a half bag of BAL "Smoke" coloured grout powder, left over from the bathroom, that I saved after Mark Fielder recommended it as an extra fine ballast, so that will be worth trying too. Currently waiting on some parts to try converting the turnout operation from the Conrad motors and white 2mm Association 3D printed tie-bars (the combination definitely works BUT feels very violent and has LOTS of tension in the actuating rods) to the 3D printed servo based design that Henk posted on the 2mm VAG email list. His design uses an ex-centre disc in a slot attached to the tie bar to translate the full 180 degree motion of the Servo into 0.8mm movement without any tension - which seems like a very good solution. Inevitably bought some parts from eBay that seem to be coming on the slow boat from China ... Justin Link to post Share on other sites More sharing options...
justin1985 Posted December 3, 2019 Author Share Posted December 3, 2019 I wasn't really that happy with the over-long throw of the Conrad point motors, especially as there wasn't enough space to leave enough length of springy actuating wire to take out some of the throw. This meant there was an awful lot of tension in the turnout mechanisms all of the time - not ideal. I've been experimenting with servos as an alternative. First off I tried a combined servo bracket and turnout operating mechanism 3D printed from a file kindly shared with me by Henk Oversloot. The beauty of this design is that it uses an eccentric cam to translate the full rotation of the servo to a very short lateral movement. This avoids any of the fiddling with exactly the right amount of rotation, and effectively removes any of the dangers of jitters or unintended full rotations. The one here still needs tubes to be attached to the bar to accept the droppers from the blades. However, this mechanism does take up quite a bit of space, and inevitably there wasn't enough clearance around any of the points on Dailuaine's second hand baseboard. I'll definitely use these on future projects though! So the solution on this layout was another bit of a bodge - servos operating the same Association 3D printed TOU bars that I'd used before with the Conrad motors. This did involve quite a lot of fiddling to get the right rotation for each, and they do over-throw when powered up etc. However, u used a very light and springy wire for the linkage (with some screws as guides), so I think there is enough slack to avoid any problems. It all runs off a MERG Servo4 controller. I found this easy to build, but a right pain to program. All of the variants of the setting software seem very flaky and buggy - perhaps because they're so old any not at home on Windows 10. Having to reboot the laptop to get the servo programming software to work again if I'd closed it and reopened got tiresome pretty quickly! In future I'd be tempted to just use an Arduino. There's still one more microswitch left to install for switching the vee polarity. Then time for some extensive testing before I paint the track and ballast. J 1 Link to post Share on other sites More sharing options...
RMweb Premium nick_bastable Posted December 4, 2019 RMweb Premium Share Posted December 4, 2019 which version of the MERG software are you using I have found ServoSetPlus works ok for me with W10 Nick Link to post Share on other sites More sharing options...
RMweb Premium Ian Morgan Posted December 4, 2019 RMweb Premium Share Posted December 4, 2019 I found the Merg hardware ServoSet unit (Kit 76A) a good investment, small and portable for grovelling about under baseboards, and utterly reliable and simple to use. I am now building a ServoSet3 that is described by Duncan Greenwood in the Merg forum and Wiki. This is Arduino based with a colour touch screen display and can be used for setting end stops and speed when connected to the Merg Servo4, plus the CANSERVO8, CANMIO-SVO and CANMIO-Universal. Just having some problems loading the software/firmware, but it looks promising. Link to post Share on other sites More sharing options...
justin1985 Posted December 4, 2019 Author Share Posted December 4, 2019 3 hours ago, nick_bastable said: which version of the MERG software are you using I have found ServoSetPlus works ok for me with W10 Nick Hi Nick, Of the various tools I found listed on the MERG forum page linked from the kit page (incredibly hard to find!) I found that "ServoSet4" (Version 3.03 by Trevor Stockill) works reasonably, apart from the issue of not actually working if closed and reopened, unless the laptop is rebooted in between. "ServoSetPlus" (version 2.02 by Trevor Stockill) seemed to default the "Off" state angle back to 127 on all the servos other than the currently showing one when I pressed "Write to Board" - which makes it utterly useless! It also had the issue of not working at all if closed and re-opened without a reboot. Perhaps there are other versions hidden away elsewhere in the MERG websites? 2 hours ago, Ian Morgan said: I found the Merg hardware ServoSet unit (Kit 76A) a good investment, small and portable for grovelling about under baseboards, and utterly reliable and simple to use. I am now building a ServoSet3 that is described by Duncan Greenwood in the Merg forum and Wiki. This is Arduino based with a colour touch screen display and can be used for setting end stops and speed when connected to the Merg Servo4, plus the CANSERVO8, CANMIO-SVO and CANMIO-Universal. Just having some problems loading the software/firmware, but it looks promising. I didn't really fancy the extra complication of building another box just to set the servos - hence the appeal of the PC for setting. It's seeming like that might have been the wrong call though! J Link to post Share on other sites More sharing options...
RMweb Premium nick_bastable Posted December 4, 2019 RMweb Premium Share Posted December 4, 2019 software versions here you need to be logged into the forum https://www.merg.org.uk/merg_wiki/doku.php?id=servoset:servoset assuming your using a usb/serial converter unplugging that and re-plugging re-powering the servoboard should resolve your need to reboot Nick Link to post Share on other sites More sharing options...
justin1985 Posted December 18, 2019 Author Share Posted December 18, 2019 I got the Servos working eventually, although I never managed to get rid of the not working when the application was re-opened. Happy to leave the point mechanisms alone for now! I haven't done the ballast yet, but I'm starting to work on the buildings a bit more. More importantly, I've done more testing, and found some tight (and wide) points on the diverging route of the re-used soldered turnout. Bad idea re-using an old early attempt at a turnout, I guess, but at least easy to adjust. Its all running pretty smoothly now though - albeit the short wheelbase J94 struggles at slow speed running using an old Bachmann trainset controller - but thats to be expected, I think. Tonight's other task has been trying out some roof slates. I like the idea of the York Modelmaking laser cut adhesive slates and tiles, so thought I'd try cutting my own, actually using the Silhouette cutter and normal black paper. I'm pretty pleased with the result. I think the silhouette actually gives a subtler result than a laser in this instance - the cut width is very narrow indeed. I stuck the rows down without any guides, just aligning one trip to the top of the notches on the previous, using Easitrack glue - because it bites quickly, and seems to stick better to plasticard than most PVA type glues. Wondering whether to seal with some kind of solvent based varnish before painting, to stop the paper absorbing paint and swelling? Finally, some experiments with lamps. I like the delicate appearance of the Ratio mouldings, and previously experimented with illuminating them using a fiberoptic as a "pole", which worked fairly well. For this layout I'd like some wall mounted gas lamps, which would make that approach trickier. This experiment has a 2.5mm dia. dimple drilled into the top of the lens moulding, and a similar indent "countersunk" into the lid moulding. Trapped between them is a 0603 surface mount LED which I soldered to some enamel wire. The idea is the wire will run down the corners of the lens, masquerading as the corner posts of the lamp at the back, with plasticard strip doing the same at the front. It does work! but I didn't have enough hands to photograph it in action. The really tricky thing was trying to glue it together, it seems like NOTHING sticks to the plastic Ratio used for the lens moulding! I might try 3D printing some parts instead - although I'd have to buy a whole bottle of clear resin for some VERY small parts ... I just found some pre-wired 0402 LEDs on eBay, so I might try mounting these into the bottom of the lens. J 9 3 Link to post Share on other sites More sharing options...
Caley Jim Posted December 19, 2019 Share Posted December 19, 2019 I wouldn't worry about the paper slates swelling. I've used acrylic paint without any problems painting slates cut from both 80gsm and newsprint paper. Jim 1 Link to post Share on other sites More sharing options...
RMweb Gold queensquare Posted December 19, 2019 RMweb Gold Share Posted December 19, 2019 Really like the lamps idea. Any chance of a picture of the other lamps you've done and some more details on the leds you've used and the power source. I've put lights in the engine sheds I built recently and retrofitted the signalboxes. I rather fancy a few lamps and have a small stash of the Ratio lamps. jerry Link to post Share on other sites More sharing options...
RMweb Premium CF MRC Posted December 19, 2019 RMweb Premium Share Posted December 19, 2019 Worth noting that the first row of slates/tiles at the gutter has a half row or kicker beneath it. Otherwise the roof does this- ) at the gutter. I would think that a sealing coat of PVA would help to take away some of the gaps between the slates. Tim Link to post Share on other sites More sharing options...
justin1985 Posted December 19, 2019 Author Share Posted December 19, 2019 1 hour ago, queensquare said: Really like the lamps idea. Any chance of a picture of the other lamps you've done and some more details on the leds you've used and the power source. I've put lights in the engine sheds I built recently and retrofitted the signalboxes. I rather fancy a few lamps and have a small stash of the Ratio lamps. jerry Hi Jerry, I'm not totally convinced it's the way to go. But worth a try, I think. These the LEDs in their packet. Basically a case of waving a soldering iron in the right direction, with plenty of flux and a very small solder ball, just hoping for best really! This was the previous experiment with 1mm fibre-optic running up a brass tube replacing the post. Three years ago now, according to the time stamp on the file! I guess this is better in a lot of ways, not least maintenance/what if the LED fails. This uses a flat-topped LED glued to the bottom of the fibre-optic with canopy glue and covered in heat shrink. I guess I used warm white? It would be tricky to do with a wall mounted lamp though, I think. I don't know if the fibre optic could be bent into a sharp enough angle? (Perhaps with heat of a soldering iron?) J 2 1 Link to post Share on other sites More sharing options...
RMweb Gold queensquare Posted December 19, 2019 RMweb Gold Share Posted December 19, 2019 Thanks Justin, I have some thin fibre optics so will give that a try. I don't want to have enough light to operate, I just fancy a few buildings and lamps lit up. - sometimes it's nice just to sit and look at our creations with a glass of something! jerry 1 3 Link to post Share on other sites More sharing options...
Popular Post justin1985 Posted December 23, 2019 Author Popular Post Share Posted December 23, 2019 I actually found a 1.2mm O/D, 1mm I/D brass tube stocked at Eileen's, so that should make a slightly more delicate version of the fibre optic lamp. The other jobs I've been doing on Dailuaine have just been packing under the sleeper gaps where I'm planning to lay DAS cobbles, to reduce the depth of the clay, and stop any bubbling up between the rail and check rail. Tedious! I also laser cut some foam for a box to contain all the wagons I'm intending to operate the layout with in BR blue period. I find the perfect fit for the wagons very pleasing! 14 6 Link to post Share on other sites More sharing options...
justin1985 Posted March 22, 2020 Author Share Posted March 22, 2020 I've been dipping into this project here and there, working on buildings, but no major progress for a while. With the announcement that the DJLC is being postponed to 2021, I actually had the thought that perhaps it was giving entering another thought, if it would be possible to cut this little layout down to fit. The layout as is stands has a scenic section just under 1m long - and a frankly too short area for cassettes - the total length is the 1220 of the short side of a sheet of ply. This is just a hangover from re-using the board that my previous Snape project was on. Here I've posed it with the 5 / 3 / 3 combination of wagons to operate as an Inglenook shunting puzzle, using the stock I've put together for the BR blue era. Even with some relatively long wheelbase wagons, it looks like I could cut about an inch from the right hand side, and still work as a shunting puzzle. Most of the length is taken up with the turnout leading to the little engine shed though. So - thought is - cut the trackbed back where the furtherest left turnout begins - roughly at the 40cm mark on the ruler - so giving a 60cm visible section. To retain the interest (and view block) of the engine shed, I thought I could add a kickback siding coming off the long siding at the front - perhaps an A5 to get the engine shed close to parallel to the exit track. This feels like less of a wrench than it might be, because I'd noticed that the track on the long front siding isn't perfectly level, causing a three legged wobble for stock. Mockup with masking tape as track! Any thoughts? Justin 4 Link to post Share on other sites More sharing options...
richbrummitt Posted March 23, 2020 Share Posted March 23, 2020 4 hours ago, justin1985 said: Any thoughts? Why potentially compromise what you have done to fit a set of rules? Instead enquire if the layout would be welcome as an exhibit, at least before baseboard surgery if that is what you eventually decide. 3 Link to post Share on other sites More sharing options...
Jan W Posted March 23, 2020 Share Posted March 23, 2020 Would it be an idea to leave the layout as it is and then add a removable side at the 60cm position. You only have to move the small building on the front a bit to the right. Looks less cramped than your mockup with the turnout moved to the siding I think. The DLJC rules only restrict the dimensions of the scenic area but you're free to do what you want with the offstage area. And of course you have to cover the front on the left side but it must be possible I think. Jan Link to post Share on other sites More sharing options...
Lacathedrale Posted March 23, 2020 Share Posted March 23, 2020 Isn't the requirement for 9.42" x 60cm? Or has it changed to square centimeters? It is of course your layout, but 'kickback off another siding' is the kind of thing you often see on shunting planks where the person has run out of ideas - quite opposed to the stringent analysis and search you've been doing. Jan's suggestion of a removable left-hand backscene that bisects the line between the opposing turnouts may be a happy compromise, assuming there's a view block planned for the middle of the scene? Link to post Share on other sites More sharing options...
RMweb Gold queensquare Posted March 23, 2020 RMweb Gold Share Posted March 23, 2020 I'd leave it as it is Justin, moving the shed to be a kick back off the front siding spoils the balance. As for Jan's suggestion, I suggested putting a removable backscene on my Midland shed scene to bring the scenic area within the rules of the DJLC but was told that wasn't permitted so didn't bother. If you really want to build a DJLC entry I would start again but, in all honesty, I think the size is just too small to make anything interesting. Jerry 3 Link to post Share on other sites More sharing options...
RMweb Premium Kylestrome Posted March 23, 2020 RMweb Premium Share Posted March 23, 2020 (edited) 12 hours ago, justin1985 said: I actually had the thought that perhaps it was giving entering another thought, if it would be possible to cut this little layout down to fit. I think the main idea behind the diamond jubilee layout competition was to encourage people to build their first layout. Restricting the size requirement was deemed to make it less daunting and easier to finish quickly (although there are probably some who are pleased to have an extra year available ). What you're already building, without needing the 'kick-start' from the DJLC, is fine as it is and you will probably later regret the lack of running space if you cut it shorter. Besides, building layouts is not a competitive sport. It has to be something that pleases you! David Edited March 23, 2020 by Kylestrome 1 7 Link to post Share on other sites More sharing options...
justin1985 Posted March 23, 2020 Author Share Posted March 23, 2020 Many thanks for the comments and suggestions. I guess I should emphasise that I'm not really motivated by the competition per-se - I was just thinking of it more just an impetus to get some momentum back into the project. I think the prospect of lifting and relaying the siding has put a bit of a dampener on it recently, so a change felt more motivating than just a fix, if that makes sense? But point taken that the cut down version would look quite cramped! I'm thinking perhaps I'll just cut off the stubby flat extension at the end that was left to support cassettes, which is too short to be useful, but still makes the layout unwieldy to move and a bit big to store on a shelf, and make something longer, but bolt-on to only fit when its in use. I did toy with a plan for a separate specific DLJC layout (a small quayside scene based on Hythe in Colchester) but quickly concluded it was too small to be interesting. So ... I guess that answers it for me! Justin 1 Link to post Share on other sites More sharing options...
justin1985 Posted May 28, 2020 Author Share Posted May 28, 2020 Progress with this layout has pottered on very slowly, I must admit. The main job at the moment is the whole range of distillery buildings, all but one in a similar dressed stone finish. I'm using Slaters embossed plasticard, but painting all that expanse of weathered stone has been a good reason to procrastinate! I have done some experiments using plenty of washes and drybrushing with Vallejo acrylics. I think, finally, I'm getting close to the quite characteristic dark (but not monochrome) stone and relatively bright contrasting mortar that you can see in the Flickr album linked at the beginning of the thread in the top left of this wall (will be hidden so using as test bed). Any thoughts? The other recent bit of progress has been cutting out the walls for the warehouse buildings. The silhouette cutter's best effort at scoring the plasticard was no way near enough for these complex shapes, so it was still an awful lot of effort cutting! Window sills and headers are the next stage. Limonene as a solvent has been effective in building up the laminations (embossed + 2 layers 0.5mm plain - bottom one with recesses for the etched windows). Once I've got the buildings all at least assembled, if not finished, I'll turn to sorting out the ground surfaces and things. The fiddle yard really needs sorting out properly too! J 14 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now