steve howe Posted October 13, 2019 Share Posted October 13, 2019 Can anyone advise if the Dundas Hudson V skip can be made to tip? I want to try to get some to unload sand into a loading chute ideally using a similar device to Giles Flavell's 'End of the Line' layout. Steve 1 Link to post Share on other sites More sharing options...
sir douglas Posted October 14, 2019 Share Posted October 14, 2019 (edited) yes, the body is seperate to the chassis and is made to tip as prototype EDIT, for some reason i replied thinking you were asking about the 16mm binnie skips but your talking 009, a quick look at the kit in image search, I would still say yes Edited October 14, 2019 by sir douglas Link to post Share on other sites More sharing options...
otherplanet Posted October 25, 2019 Share Posted October 25, 2019 I have been considering the same question just recently. My conclusion was yes, but not well. If you build the kit as instructed, but dont glue the skip to the body. It will tip, and if filled with a load of sand it runs precariously but stable over a simple short length of track and will then dump the load fairly nicely if you push it in just the right way. But, once they are empty, the skip wobbles around all over the place and easily rattles out of alignment. Repeated tests showed skip to be inclined to fall off with the slightest knock or bump. They dont have the mass to hold the skip in place properly, Weight doesnt scale well. It was also very easy to knock the skip off if I didnt push it exactly right when tipping and they tended to try and right themselves awkwardly once empty. I then tried kitbashing, using the chassis and skip but building new support ends based on the arched top frame style. I scaled the dimensions from the Robert Hudson catalogue, republished by the narrow gauge railway society. With the higher structures around the flat support plate of this design, the skip stays in place when running and when tipping. It also has a little friction which keeps the rattle under control. The first one seems to work well so I am going to try a small rake and then see if I can get the tipper mechanism to work. See below. Std version on the right. Modified version on the left. Please excuse the paint job, the next experiment was an excersise in trialling new rust painting techniques. Hope that helps 2 Link to post Share on other sites More sharing options...
steve howe Posted October 26, 2019 Author Share Posted October 26, 2019 Thanks indeed, that looks like a way forward. I only intend running three in a rake, but lightness was an issue I was concerned about. I was also thinking about the Snailbeach type side tipping wagons but I am not sure if anyone makes a kit for them in 4mm? Steve Link to post Share on other sites More sharing options...
steve howe Posted October 26, 2019 Author Share Posted October 26, 2019 I see that Peco also do their own tipper GR-330 OO-9 V-Skips Hudson Rugga, anyone any experience of these? Steve Link to post Share on other sites More sharing options...
luke the train spotter Posted October 26, 2019 Share Posted October 26, 2019 5 hours ago, steve howe said: I see that Peco also do their own tipper GR-330 OO-9 V-Skips Hudson Rugga, anyone any experience of these? Steve I've got a couple packs of the rugga skips and the tipper bit is a separate piece of plastic to the chassis but they snap in place to hold them in place so probably quite difficult to modify them to tip. Link to post Share on other sites More sharing options...
steve howe Posted October 26, 2019 Author Share Posted October 26, 2019 I've been doing a bit more digging around on this matter and there is a thread on just this subject: https://www.rmweb.co.uk/community/index.php?/topic/120156-009-working-tippers/&tab=comments#comment-2625482 and following SVRLad's suggestion am looking at the ROCO vee skip as an option. They tip as required (apparently) and run well, They are higher in the body than the Hudson version but as these things were produced in a wide range of sizes and shapes, I can live with that for my modest needs! I would be interested to hear how the Peco ones perform though. Link to post Share on other sites More sharing options...
BernardTPM Posted October 26, 2019 Share Posted October 26, 2019 There's a small, short round peg just under the supports {visible in the above photo) that you will need to remove to make the skips tip, but they can be made to work like that. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now