TrainMan2001 Posted May 26, 2020 Share Posted May 26, 2020 I have been struggling to cut curves in plasticard without the knife doing straight segments in it, so I have been wondering, how do you do it? I've seen people's work with curves cut into them, but I just can't seem to do it myself. Do you have any tips? I've also thought a little bit about working with brass, but I don't really know what tools to use to cut it. Any tips here? Thanks for any information you can provide! Link to post Share on other sites More sharing options...
CKPR Posted May 26, 2020 Share Posted May 26, 2020 Try using a 'compass cutter' for curves in plasticard - as for cutting curves in brass or very thick plasticard (>46 thou) , a fretsaw with a fine tooth blade is your best bet. Link to post Share on other sites More sharing options...
Tony Cane Posted May 26, 2020 Share Posted May 26, 2020 For curves in plastcard I use a Olfa compass cutter. https://www.ebay.co.uk/itm/OLFA-Compass-Cutter-And-5-Cutter-Blades-CMP-1/164010523107?epid=2254772265&hash=item262fc9f9e3:g:zogAAOSw50VeCPKI For brass the most useful tool is a piercing saw. https://www.ebay.co.uk/itm/Adjustable-Jewellers-Piercing-Saw-Frame-Tool-With-Over-100-Spare-1-0-Blades/324177175563?hash=item4b7a77240b:g:ZLgAAOSwIzpey6yR For thin brass you need fine blades typically 4/0, but best to by a bulk pack such as https://www.ebay.co.uk/itm/1-0-to-6-0-1-to-6-Jewellers-Saw-Blades-Pack-288-Various-Piercing-Blades-tool/293187973421?hash=item44435d712d:g:kg0AAOSwB-1Y79fp The saw will take some practice to get use to, and is also best used with a table such as this. Either bought or home made. 2 1 Link to post Share on other sites More sharing options...
ejstubbs Posted May 26, 2020 Share Posted May 26, 2020 3 minutes ago, Tony Cane said: The saw will take some practice to get use to, and is also best used with a table such as this. Either bought or home made. AKA a "jeweller's peg" - useful to know if you want to search for one online. Brenton, the silversmith on The Repair Shop, is often shown using one. Can be acquired fairly cheaply if you shop around. Link to post Share on other sites More sharing options...
doilum Posted May 26, 2020 Share Posted May 26, 2020 Agree with all the above. Make sure the saw is the adjustable type. The choice of blade is important for cutting Plasticard. Everyone has their own favourite but it is important to use a small sharp blade in a handle you feel comfortable with. My choice is the Exacto #2. Thin plasticard ( and shim brass) can be cut with a pair of sharp scissors. The thing is to keep trying and learning. Link to post Share on other sites More sharing options...
RMweb Gold 88C Posted May 26, 2020 RMweb Gold Share Posted May 26, 2020 All good tips above. If I can add a couple more, firstly for plastic, don’t press too hard. For both materials if you cut on the waste side of your line you can then file back to shape, cheap nail files are handy for plastic. Don’t worry if you get it wrong first time, it is all part of the learning curve, we have all been there. Brian Link to post Share on other sites More sharing options...
michl080 Posted May 26, 2020 Share Posted May 26, 2020 2 hours ago, ejstubbs said: AKA a "jeweller's peg" - useful to know if you want to search for one online. Brenton, the silversmith on The Repair Shop, is often shown using one. Can be acquired fairly cheaply if you shop around. If you want to use it for brass, I recommend to drill a 3mm hole into one of the wings. Thread the saw blad through the hole or use the saw to make a narrow slot to the hole. The advantage of the small hole is that thin brass doesn't bounce while sawing. If the saw isn't moving smoothly, your blades are too coarse. As a rule of thumb, at least three teeth should be in contact with the brass sheet. and most importantly: cheap saw blades are a pain in .... For straight cuts in brass, use an OLFA PC-L scorer and a steel ruler. Michael 1 Link to post Share on other sites More sharing options...
John Harris Posted May 26, 2020 Share Posted May 26, 2020 6 hours ago, TrainMan2001 said: I have been struggling to cut curves in plasticard without the knife doing straight segments in it, so I have been wondering, how do you do it? I've seen people's work with curves cut into them, but I just can't seem to do it myself. Do you have any tips? I've also thought a little bit about working with brass, but I don't really know what tools to use to cut it. Any tips here? Thanks for any information you can provide! I rarely use a blade to cut plastic card, I use a scriber (kept for the purpose so it stays sharp) and use several passes, rather than cutting through it one go. As other have said there are several proprietary products for cutting circles, but for other curves I use the scriber and either a card template, french curves or one of those flex-curves as a guide. jh Link to post Share on other sites More sharing options...
JeffP Posted May 26, 2020 Share Posted May 26, 2020 I've recently needed to effect a repair on an older Wickes electric tile cutter. The part, which enclosed the blade underneath and went into the water bath, was 2mm thick plastic. I sourced some off ebay, used the older part(s) as a template and scored round it. I then cut it out using an electric jigsaw with a fine toothed blade, on a low speed . The work of two minutes to produce quite a complex shape. Link to post Share on other sites More sharing options...
TrainMan2001 Posted May 26, 2020 Author Share Posted May 26, 2020 Thanks everyone! That's all really helpful! Link to post Share on other sites More sharing options...
PenrithBeacon Posted May 26, 2020 Share Posted May 26, 2020 It's been a while since I cut curves in brass, but for plasticard I stick a drawing into it and then, with a sharp, pointed scalpel, just push into it. Finish off with a file, using a finger to judge if the radius is constant. Cheers Link to post Share on other sites More sharing options...
Guy Rixon Posted May 26, 2020 Share Posted May 26, 2020 For cutting thin brass (< 0.5mm) snips may be better than a saw. It's hard to get enough teeth in contact on 0.35mm sheet, so the saw catches and judders. Finer blades judder less but are easier to brake. Snips are quicker and easier to control, but do tend to curl up the brass. If the brass is very thin (0.25mm or less) it can be cut with good scissors ... but they won't stay good scissors for very long if used like that. Link to post Share on other sites More sharing options...
doilum Posted May 26, 2020 Share Posted May 26, 2020 1 hour ago, Guy Rixon said: For cutting thin brass (< 0.5mm) snips may be better than a saw. It's hard to get enough teeth in contact on 0.35mm sheet, so the saw catches and judders. Finer blades judder less but are easier to brake. Snips are quicker and easier to control, but do tend to curl up the brass. If the brass is very thin (0.25mm or less) it can be cut with good scissors ... but they won't stay good scissors for very long if used like that. Amazingly I have had only two pairs in twenty years. Both ( pinched from the kitchen) have had a hard life in the garage cutting fibreglass etc etc. The first pair were retired when the plastic handle broke. Neither were expensive, the type that can be bought in the kitchenware department for around a fiver. Thicker brass goes through the bandsaw leaving around a millimeter to clean up with a file. It helps to feed it through the bandsaw on piece of sacreficial hardboard. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now