RMweb Gold halsey Posted September 23, 2020 RMweb Gold Share Posted September 23, 2020 (edited) Hi, I've just today I turned on my DCC controller and started to get my stock of (all Bachmann) locos going - all 5 steam locos seem to running be OK and my 2 diesels are being "grumpy"- is it a reality that the means of propulsion on (Bachmann) diesels is more temperamental than on steam?? Is it unrealistic to expect to go back to my layout after 6 months clean the track (which is OK and understandable) and expect all locos to work?? I seem to remember from last winter that the diesels seemed to be far more sensitive to track conditions and servicing - this is new to me but is this a well known issue to others?? I think I'm going to move these items on - they do both work perfectly OK but just seem to need more care and attention - deep down I prefer steam anyway so its not a big issue . Comments??? QUESTION Is there a star/stand out performing DCC fitted (Bachmann?) LMS or BR Early Emblem steam loco out there Edited September 23, 2020 by halsey Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted September 23, 2020 Share Posted September 23, 2020 7 hours ago, halsey said: I've just today I turned on my DCC controller and started to get my stock of (all Bachmann) locos going - all 5 steam locos seem to running be OK and my 2 diesels are being "grumpy"- is it a reality that the means of propulsion on (Bachmann) diesels is more temperamental than on steam?? Is it unrealistic to expect to go back to my layout after 6 months clean the track (which is OK and understandable) and expect all locos to work?? I seem to remember from last winter that the diesels seemed to be far more sensitive to track conditions and servicing - this is new to me but is this a well known issue to others?... Quite the reverse in my experience. The all wheel drive and pick up combined with good mass makes them very reliable and less temperamental than steam. One singular weakness though, which I correct the moment basic testing has proved the model is reliable. That's the clip on connections of the wires to the circuit board. It's not the best assembly method and soldering all these connections makes a world of difference. 7 hours ago, halsey said: Is there a star/stand out performing DCC fitted (Bachmann?) LMS or BR Early Emblem steam loco out there LMS: Fairburn 2-6-4T BR: 9F Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 23, 2020 Author RMweb Gold Share Posted September 23, 2020 1 hour ago, 34theletterbetweenB&D said: Quite the reverse in my experience. The all wheel drive and pick up combined with good mass makes them very reliable and less temperamental than steam. One singular weakness though, which I correct the moment basic testing has proved the model is reliable. That's the clip on connections of the wires to the circuit board. It's not the best assembly method and soldering all these connections makes a world of difference. LMS: Fairburn 2-6-4T BR: 9F Thanks - is the circuit board tip a diesel tip or a steam tip (or both?) Will review both Locos........ Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted September 23, 2020 Share Posted September 23, 2020 1 hour ago, halsey said: Thanks - is the circuit board tip a diesel tip or a steam tip (or both?) Diesel (and probably electrics too, but never had one to look at). Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 24, 2020 Author RMweb Gold Share Posted September 24, 2020 The DMU seems to be the most temperamental so I will have a look at that later......... Thanks Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted September 24, 2020 Share Posted September 24, 2020 Ah, Bachmann's DMU's are different again from their twin bogie diesel traction design! The pick up on the split axle principle is very good, all wheels pick up, but the transfer between bogies and the body PCB is made by rubbing contacts. Soldering on flexible wire links is one solution. Adding track power links between powered and trailer cars makes them 'bombproof', whole unit picking up on all wheels. Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 24, 2020 Author RMweb Gold Share Posted September 24, 2020 3 hours ago, 34theletterbetweenB&D said: Ah, Bachmann's DMU's are different again from their twin bogie diesel traction design! The pick up on the split axle principle is very good, all wheels pick up, but the transfer between bogies and the body PCB is made by rubbing contacts. Soldering on flexible wire links is one solution. Adding track power links between powered and trailer cars makes them 'bombproof', whole unit picking up on all wheels. More info please......................thanks - other Diesel loco (LMS10000) now running OK - it was a plastic bar link between the bogie and the motor which seemed to have sprung out. Link to post Share on other sites More sharing options...
34theletterbetweenB&D Posted September 24, 2020 Share Posted September 24, 2020 If you take the bodies off the DMU's - quite a struggle to avoid damage on the Cravens (class 105) which I have - you can then remove the seating moulding to uncover the PCB. Identify the PCB tracks which carry track power. Solder on thin flexible wire to link these tracks between the vehicles. Thus far I have made mine permanently wired pairs, but a plug and socket could be arranged, or even conductive couplings if desired. 1 Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 26, 2020 Author RMweb Gold Share Posted September 26, 2020 (edited) On 24/09/2020 at 07:33, halsey said: The DMU seems to be the most temperamental so I will have a look at that later......... Thanks I seem to have improved the running of this unit by changing the CV1 value from 1 to 50 (I tried 10/25/100 values) - does that make sense - I haven't really "played" with CV settings since making the DC/DCC change so I think this year I will take the plunge a bit more. Edited September 26, 2020 by halsey Link to post Share on other sites More sharing options...
John Tomlinson Posted September 26, 2020 Share Posted September 26, 2020 The Bachmann DMU's seem particularly prone to poor running after an interval. I found a lot of this is due to excess grease on the axles and bearings, which as these are the conducting path for the current makes problems hardly surprising. One solution is to fit proper wiper pickups to the backs of the wheels, otherwise a good clean and minimal lubrication seems to do the trick in most cases. John. Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 26, 2020 Author RMweb Gold Share Posted September 26, 2020 21 minutes ago, John Tomlinson said: The Bachmann DMU's seem particularly prone to poor running after an interval. I found a lot of this is due to excess grease on the axles and bearings, which as these are the conducting path for the current makes problems hardly surprising. One solution is to fit proper wiper pickups to the backs of the wheels, otherwise a good clean and minimal lubrication seems to do the trick in most cases. John. Thanks - it is now running much better and after having left it doing so for about an hour. I think I am possibly falling into the novices trap of over lubricating, I'm using the right oil and its only on the running gear as I don't like taking bodies on and off too much but I might do some IPA cleaning and review. Link to post Share on other sites More sharing options...
John Tomlinson Posted September 26, 2020 Share Posted September 26, 2020 (edited) 15 minutes ago, halsey said: Thanks - it is now running much better and after having left it doing so for about an hour. I think I am possibly falling into the novices trap of over lubricating, I'm using the right oil and its only on the running gear as I don't like taking bodies on and off too much but I might do some IPA cleaning and review. I'm glad you're seeing improvement. The excess grease I referred to was put on in the factory, and is a regular curse of much RTR. Bachmann locos generally used to be dreadful, but also other makes as well. Thankfully they seem less prone these days to going berserk with the grease gun! You actually don't need much oil at all, and I've found the bottles supplied by the likes of Labelle with a thin pipe feed help get the stuff where its needed and nowhere else. It is literally one or two drops on an axle bearing, probably just one. It's worth as well wiping off any excess after you've oiled before going back on the track, otherwise you're just increasing your cleaning workload for the future! There are some thicker greases available for the worms and gears if needed but to access you do need to get inside. Again, you only need a tiny bit and it will work its way around. John. Edited September 26, 2020 by John Tomlinson typo 1 Link to post Share on other sites More sharing options...
Il Grifone Posted September 27, 2020 Share Posted September 27, 2020 The advice with oil was always, "If you can see it, you've used too much!" 1 1 Link to post Share on other sites More sharing options...
RMweb Premium PaulCheffus Posted September 28, 2020 RMweb Premium Share Posted September 28, 2020 On 26/09/2020 at 12:22, halsey said: I seem to have improved the running of this unit by changing the CV1 value from 1 to 50 (I tried 10/25/100 values) - does that make sense - I haven't really "played" with CV settings since making the DC/DCC change so I think this year I will take the plunge a bit more. Hi I’m intrigued how changing the short address has any effect on how well it runs. CV1 - Short address CV17 & 18 plus CV29 bit 5 = 1 - Long address Cheers Paul Link to post Share on other sites More sharing options...
RMweb Gold halsey Posted September 28, 2020 Author RMweb Gold Share Posted September 28, 2020 29 minutes ago, PaulCheffus said: Hi I’m intrigued how changing the short address has any effect on how well it runs. CV1 - Short address CV17 & 18 plus CV29 bit 5 = 1 - Long address Cheers Paul I should have been more clear - it changes the response time from stationary which I prefer Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now