wandering blue Posted December 3, 2020 Share Posted December 3, 2020 Hello . I've got one of these as a trial to see if they make any sense: https://www.tillig.com/eng/Produkte/produktinfo-85139.html The principle is to have overlapping chamfered cut rails in the centre of a short length of track, so that one end can be slid out up to 5mm across baseboard joints. Evidently electrical continuity therefore relies on the opposing faces on the joint; perhaps an additional pair of flexible droppers would solve that if it were problematical. The friction at the joint relies only on the plastic chairs and I can see this loosening over time. They go against the grain of soldering baseboard-edge rail ends to either copper clad or brass screws. I'm not sure they will work for me, as many of my tracks crossing baseboard edges are not straight, and although you can flex Tillig Elite track, to do so in this instance opens up the chamfered track joints. Trust the above is of use. Has anyone used these successfully, with or without Tillig Styrostone pre-ballasted underlay? Wandering Blue 1 Link to post Share on other sites More sharing options...
RMweb Premium Chimer Posted December 4, 2020 RMweb Premium Share Posted December 4, 2020 Not used, I'm afraid, but I quite like the idea, as I'm totally inept with a soldering iron. However I note the track across the joint doesn't just have to be straight, it has to be at exactly 90 degrees to the edge. And yes, I would have separate cross-board electrical connections using banana plugs or similar rather than relying on the track. Interesting, though .... Link to post Share on other sites More sharing options...
RMweb Premium Keith Addenbrooke Posted December 6, 2020 RMweb Premium Share Posted December 6, 2020 I may be missing something, but doesn’t the track from one board have to protrude beyond the edge when the boards are separated, so it will mate properly when the boards are pushed together? If so, there’s a risk of damage to the protruding bits? Link to post Share on other sites More sharing options...
Butler Henderson Posted December 6, 2020 Share Posted December 6, 2020 (edited) 14 minutes ago, Keith Addenbrooke said: I may be missing something, but doesn’t the track from one board have to protrude beyond the edge when the boards are separated, so it will mate properly when the boards are pushed together? If so, there’s a risk of damage to the protruding bits? I've used a similar with N Kato Unitrak albeit obviously a lot stronger, with the track section not extended it is flush with the edge of board and then with the boards joined extended to connect with the track on the other board, Edited December 6, 2020 by Butler Henderson Link to post Share on other sites More sharing options...
RMweb Premium Keith Addenbrooke Posted December 6, 2020 RMweb Premium Share Posted December 6, 2020 4 minutes ago, Butler Henderson said: I've used a similar with N Kato Unitrak albeit obviously a lot stronger, with the track section not extended it is flush with the edge of board and then with the boards joined extended to connect with the track on the other board, Ah, got it! Thank you - so the whole piece stays on one board, then one side extends (like a step ladder) over the gap. I agree with the earlier posts that use is limited to straight joins perpendicular to the baseboard edge - but if it’s marketed as a ‘module joiner’ that’s fair enough: the module specs I’m familiar with require that anyway. Link to post Share on other sites More sharing options...
Butler Henderson Posted December 6, 2020 Share Posted December 6, 2020 There is a bit of wriggle room with extendible sections in terms of not having to be a ninety degrees to the baseboard edge . This one is a bit short in terms of how far it extends but it could be arranged on an angle with one rail is at the baseboard edge and the other up to 5mm back. 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now