Barnaby Posted January 12, 2021 Share Posted January 12, 2021 It must be said that Bantam Street Yard is a wonderful layout Gareth. The more I look at it the more I'm tempted to re-invest in 00 but then I've looked at a direct track comparison in 0 gauge which would only require some 6 1/2ft to build BSY on. Sets me thinking on what if I was to stretch that 6 1/2ft up to 8 ft for 0 gauge. Mmmmmnn i think I'll get out of your thread and go and have a ponder over on mine limiting my layout space to 8ft [2 x 4ft boards]. Now where are my stash of small 0 gauge track plan books. 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 17, 2021 Author RMweb Gold Share Posted January 17, 2021 (edited) Thanks for the very kind words...long way to go yet though! Wiring pretty much complete now. I might put a couple of isolated sections in later, but I'm pretty much working on the one engine in steam principle. The sector plate self isolates when not lined up. The little point actuator mechanisms work quite well. Edited January 17, 2021 by Gareth001 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 17, 2021 Author RMweb Gold Share Posted January 17, 2021 (edited) Started to make some simple mockups of buildings to get an idea of how things will fit. This is going to be a sort of granary / mill thingy which straddles the sector plate, hiding most of it from view. The terraced house is a scaled down version of my 7mm kit, but I'm still doing the artwork for the windows, so it's just a shell at the moment. I'm going to incorporate at least one pair of these along the backscene. Edited January 17, 2021 by Gareth001 5 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 17, 2021 Author RMweb Gold Share Posted January 17, 2021 Here's a better view of the sector plate entrance. With another structure to the right of the entrance track it should be disguised pretty well. 14 Link to post Share on other sites More sharing options...
RMweb Gold Sweet pea Posted January 18, 2021 RMweb Gold Share Posted January 18, 2021 Gareth I like your mock up of the industrial buildings. 2 Link to post Share on other sites More sharing options...
Barnaby Posted January 18, 2021 Share Posted January 18, 2021 (edited) Yes some may say it is a "mock up" but it puts my builds to shame. E.G. Gareth's mock ups are just that much better than my so called finished builds. Best Edited January 19, 2021 by Barnaby add eg Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 19, 2021 Author RMweb Gold Share Posted January 19, 2021 (edited) I fancy the idea of the front of the baseboard being part of the scenery, so I'm going to make an old harbour wall, with the idea that it could be a silted up canal basin or disused estuary port, or the tide could be out. This is part of the master, made from 10 thou styrene stones on a 20 thou backing. When it's finished I'll make a mould and cast enough for the whole of the front of the layout. Sorry about the poor photo, and I couldn't rotate it for some reason. Edited January 19, 2021 by Gareth001 4 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 20, 2021 Author RMweb Gold Share Posted January 20, 2021 Finished the pattern for the dockside wall, and remembered again why I moved to the more optically friendly 7mm scale. Drilling the holes to represent where the chair bolts had been in re-used sleepers was particularly migraine inducing. We'll see how the mould comes out in the morning....I'm a little apprehensive about the overhang in the pattern to allow the panels to link together, but I think the mould will be flexible enough to deal with it. 4 3 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 21, 2021 Author RMweb Gold Share Posted January 21, 2021 First castings out of the mould. Couple of schoolboy errors though...I didn't really use enough latex (cos I'm a skinflint) so the mould is a bit thin on the overlap areas, so may not last too long. I still have the pattern though, so I can make another mould. I've also realised that I should have made the panels a bit bigger than the depth of the baseboard edge, so that they at least match the rail height. I'll have to mount them a little higher...ho hum. I think the castings look ok though. They fit together nicely, and could also be used for some applications in 7mm too. 1 3 Link to post Share on other sites More sharing options...
Barnaby Posted January 21, 2021 Share Posted January 21, 2021 That looks very good Gareth. Re the overlap issue couldn't you just make the start and end of a wall panel be where the verticals are and add one per join separately once the panels are butted up together. I'm not too sure what you have found out of true with the mould overlap so I'm guessing a bit with my suggestion. Best Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 21, 2021 Author RMweb Gold Share Posted January 21, 2021 Hi Barnaby. the panels don't just butt up together: the timber stanchion at the right hand end of the panel is cast half on and half off the stone section behind, so that when the panels are put together it overlaps the adjacent one. I don't think I've described it very well...I'll post a pic tomorrow. What this means is that the edge of the mould is wider at the bottom than at the top ( the same apples to the part where the stanchions rise above the wall). This in turn means the casting has to be coaxed out of the mould, which is not usually a problem as long as the undercut is not too deep, or the mould above the undercut is not too thin because someone is too mean to use any more latex. Lesson learned! 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 22, 2021 Author RMweb Gold Share Posted January 22, 2021 The pics below show what I was trying to describe. You can see what I mean about the weakness of the mould at the top. The closeup is a bit cruel, and shows flash on the mould I hadn't even noticed. Having seen that, I'm surprised (but pleased) that the castings come out as well as they do! 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 22, 2021 Author RMweb Gold Share Posted January 22, 2021 And some pics of the row of castings in place (sort of). When I stick them on I'll raise them a bit so the railhead isn't higher than the dockside. 2 1 Link to post Share on other sites More sharing options...
Phil Traxson Posted January 22, 2021 Share Posted January 22, 2021 (edited) Exactly the same system as I used on my Quayside layout in 0-16.5. I cast 3 bay sections, you can see where the joins are by the gap in the top timbers which would have been visible any way in real life, I figured 30 feet would be just about a handleable length for timber baulks and a sensible length to get out of a tree trunk. The dressed capping stones are actually separate from the quay wall and are lengths of unequal leg "L" shaped plastic overlapping the edge of the casting, with the stones scribed in, no two are exactly the same length or width as the ones next to it. These are copied from the ones on Port Dinorwic quayside in North Wales, inspired by an article on it's build in in an issue of Narrow Gauge and Industrial Railway Modelling Review some years back, and several subsequent visits to it during my days off from volunteering on the Festiniog Railway. The bollards are copied from there too. I still have the moulds and patterns in 7mm scale for the walls and bollards so castings are available to order for any one by request to Port Wynnstay Models. Edited January 22, 2021 by Phil Traxson 7 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 26, 2021 Author RMweb Gold Share Posted January 26, 2021 I've scaled down a version of my own 7mm kit for a terraced house, and although the muntins (or glazing bars) have lost a tiny bit of definition when compared to the O gauge version, I'm quite pleased with the result. The kit is designed to give the builder a choice of finishes and detailing: what is shown here is the unpainted version of the basic kit. I'm going to put a representation of a rendered finish on this pair. 4 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 28, 2021 Author RMweb Gold Share Posted January 28, 2021 Here's the 7mm version for comparison. 5 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted January 28, 2021 Author RMweb Gold Share Posted January 28, 2021 (edited) I've made a start on the mill building, cutting out the front elevation and lightly scribing on guidelines for the weatherboarding. I had some problems with the windows to begin with until I discovered a line overcut feature on the cutter, and increased the thickness of the glazing bars by 0.02mm. Mk1, 2 and 3 below. I think this is about the limit for this machine, but I don't think such fine details could be achieved with casting or a laser cut (I could be wrong!). Even a brass etching would be a challenge, and expensive too. Edited January 28, 2021 by Gareth001 2 1 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted February 13, 2021 Author RMweb Gold Share Posted February 13, 2021 The wharf wall now in position, with a quick misting of greeny sludge over grey primer, prior to weathering proper. 8 Link to post Share on other sites More sharing options...
RMweb Gold Sweet pea Posted February 15, 2021 RMweb Gold Share Posted February 15, 2021 The wharf wall looks nicely modelled Gareth. 2 Link to post Share on other sites More sharing options...
RMweb Gold Gareth001 Posted February 15, 2021 Author RMweb Gold Share Posted February 15, 2021 Thanks Kevin...I hope it'll look better when I've done some more detailing, painting and weathering. 1 Link to post Share on other sites More sharing options...
Oncomin5torm Posted May 29, 2023 Share Posted May 29, 2023 On 28/12/2020 at 17:09, Gareth001 said: Having started modelling in 7mm scale, and decided I'd never go back to anything smaller, I made the fatal mistake of ordering a Hornby Peckett, just because they're so gorgeous. In ex works livery, it sat in it's box for over a year, while work on my O gauge layout had almost stalled as I'd been spending time on commissions and making resin and CNC cut 7mm scale buildings that I produce on a short run basis. I started to wonder about producing a little "photo plank", to give the little Peckett somewhere to shuffle about and perhaps as a presentation piece if I scaled down some of my buildings to 4mm scale. While I was thinking about this, I came across the Norfolk Heath Works Micro Modules baseboard kits, intended for 009, and wondered if I could squeeze a little OO gauge micro onto them, so ordered 3 modules (including a sector plate) which duly arrived. They went together very easily and I can report they are a very nice piece of work, and reasonably priced. Then came the challenge of whether a believable little scene with a bit of operational interest could be made to fit. I had a few bedraggled old bits and pieces of track from a previous stalled layout lurking in corners of the garage, which were enough to come up with this basic plan. Hi Sorry to resurrect an old thread but I've been looking at getting some. Of the norfolk heath baseboards and I cannot get in touch with them. Ive tried Facebook and email but no reply. Where did you order yours from? Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now