GEOEng03 Posted February 10, 2021 Share Posted February 10, 2021 Hi Appreciate this may have been done to death, but I'm struggling to understand everything that I've read so far. I just want to know if the Cobalt iP Analogue switches polarity on frogs when wired in. I can see the iP digital does, but not entirely sure for iP Analouge. Best regards Link to post Share on other sites More sharing options...
RMweb Gold teaky Posted February 10, 2021 RMweb Gold Share Posted February 10, 2021 Yes it does. https://www.dccconcepts.com/manual/owners-manual-cobalt-ip-analog-point-motors/ 1 Link to post Share on other sites More sharing options...
DCCconcepts Posted February 11, 2021 Share Posted February 11, 2021 19 hours ago, GEOEng03 said: Hi Appreciate this may have been done to death, but I'm struggling to understand everything that I've read so far. I just want to know if the Cobalt iP Analogue switches polarity on frogs when wired in. I can see the iP digital does, but not entirely sure for iP Analouge. Best regards As Teaky says, the Analog IP will switch frog polarity. It has two built in changeover switches (S2 and S3) that can be used for frog polarity and other switching - such as signals. Reversing DC (regulated) to DC IN (terminals 1/2) to control the direction of the motor. Track power to S2L and S2 R (terminals 4/5) and frog to S2C (terminal 6). If the frog polarity is incorrect, swap the track feeds on S2L/R. Hope this helps. Best Regards The DCCconcepts Team 1 Link to post Share on other sites More sharing options...
GEOEng03 Posted February 14, 2021 Author Share Posted February 14, 2021 Thanks all for the replies. Sorry for delay as well. Excellent reply that tells me just what is needed as well. OK, so going to ditch the SMP point motors and frog juicers and replace with these. I have a single analogue motor, but wondering if it is worth spending just a bit more on the digital versions - incase i decide to use the controller. I want to have switches at the front of the layout for control ideally, but wondering whether the small additional layout in money might be a better option! Best Bryn Link to post Share on other sites More sharing options...
DCCconcepts Posted February 15, 2021 Share Posted February 15, 2021 On 14/02/2021 at 17:01, GEOEng03 said: Thanks all for the replies. Sorry for delay as well. Excellent reply that tells me just what is needed as well. OK, so going to ditch the SMP point motors and frog juicers and replace with these. I have a single analogue motor, but wondering if it is worth spending just a bit more on the digital versions - incase i decide to use the controller. I want to have switches at the front of the layout for control ideally, but wondering whether the small additional layout in money might be a better option! Best Bryn You essentially have 2 options to go digital later: Fit your analog motor with a suitable decoder - such as the AD-*FX range Or - fit a Digital IP in the first place and power it from your DCC bus. Control it by using two pushbuttons or a spring to centre SPDT switch connected to the PBS terminals 7/8/9. You could even just use one pushbutton connected 7-9 and toggle the motor. It's up to you whether you give it an address or not - they are happy working with either DCC commands or from the "manual" PBS terminals at the same time. If it is powered from your track bus, then simply connect terminal 3 to your electrofrog. If the polarity is incorrect, swap over the DCC IN feed wires. Hope this helps. Best Regards, The DCCconcepts Team Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now