RMweb Gold nest Posted February 23, 2021 RMweb Gold Share Posted February 23, 2021 Hello Everyone Not sure if this is the best place but a quick question regarding window frames. I am currently on my first round of proper scratchbuilt buildings and am stuck at a crucial moment. I am curious as to what methods people have used aside from buying ready made frames? I am working to some specific sizes so am currently struggling to find suitable ready made ones. I am inclined to cut out from card but am worried about the strength of these during assembly. Any guidance much appreciated! Nestor Link to post Share on other sites More sharing options...
Paul H Vigor Posted February 23, 2021 Share Posted February 23, 2021 Light gauge plasticard steet, a selection of microstrips and a craft knife with a selection of new blades! 1 Link to post Share on other sites More sharing options...
Stuart Birks Posted February 23, 2021 Share Posted February 23, 2021 What style of window are you trying to create. These are from Bradford on Avon station and are made from profiled plastic strip backed with a custom made etch. Whereas these are just done with white paint in a bow pen with some plastic strip added around the edge to give a bit of depth. Stu 6 1 Link to post Share on other sites More sharing options...
RMweb Gold nest Posted February 23, 2021 Author RMweb Gold Share Posted February 23, 2021 Thanks both of you The ones currently in question are for a small Bavarian Engine Shed in H0. I like the idea of white paint with plastic strip round the edge. These look closer to what I have in mind. I will do some experimenting with both Plasticard strip and white paint and see which my hands are more capable of doing. Previous buildings have been from kits but I'm keen to get some scratchbuilding done well. Thanks Nestor 1 Link to post Share on other sites More sharing options...
Paul H Vigor Posted February 23, 2021 Share Posted February 23, 2021 It's about gathering a few simple tools - blades, straight edges, files, etc - and having a go. Each one you make will be better than the last, because you learn as you model. 1 Link to post Share on other sites More sharing options...
RMweb Gold nest Posted February 23, 2021 Author RMweb Gold Share Posted February 23, 2021 11 minutes ago, Paul H Vigor said: It's about gathering a few simple tools - blades, straight edges, files, etc - and having a go. Each one you make will be better than the last, because you learn as you model. Exactly, lockdown furlough is providing plenty of time for experimenting... Nestor 1 Link to post Share on other sites More sharing options...
RMweb Gold ikcdab Posted February 23, 2021 RMweb Gold Share Posted February 23, 2021 Many different methods. I draw them out on the pc, print them onto ordinary paper then cut out with a sharp scalpel. Then stick to glazing. You can see examples on my layout thread. I'm thinking of a "Worgret Junction' style signalbox, so might try the bow pen route for that. 1 Link to post Share on other sites More sharing options...
brossard Posted February 23, 2021 Share Posted February 23, 2021 I am doing 0 gauge and building kits from Scalescenes and FineScale Buildings (now gone alas). Getting windows to look reasonable in this scale means I can't use the recommended methods in the kits. My approach was to make a jig for all the planned windows and layer up the windows using plastic strip. Very much a matter of making it up as I went along, but the results are pretty reasonable I think. This picture summarizes what I did: These are windows for the FineScale Buildings Station Masters House. I used the LCut window, lower right, as a model. I did look around for ready made windows, like LCut, but didn't find anything suitable. If you are scratch building you can size your door and window apertures for, say, LCut. Doors were tackled in a similar way: HTH John 6 Link to post Share on other sites More sharing options...
brossard Posted February 23, 2021 Share Posted February 23, 2021 I should add that LCut come in 4mm scale. Brassmasters do a superb range of etched 4mm brass windows and doors designed for Scalescenes kits. John 1 Link to post Share on other sites More sharing options...
RMweb Gold nest Posted February 23, 2021 Author RMweb Gold Share Posted February 23, 2021 Thanks guys There's some very useful pointers here, I'll report back in due course with results... Nestor Link to post Share on other sites More sharing options...
BrushType4 Posted February 24, 2021 Share Posted February 24, 2021 (edited) 10 hours ago, nest said: Thanks guys There's some very useful pointers here, I'll report back in due course with results... Nestor I also supply lasercut 4mm windows and I will produce bespoke sizes and designs quite reasonably priced if you need. Edited February 24, 2021 by BrushType4 1 2 Link to post Share on other sites More sharing options...
RMweb Premium Blandford1969 Posted February 24, 2021 RMweb Premium Share Posted February 24, 2021 2 hours ago, BrushType4 said: I also supply lasercut 4mm windows and I will produce bespoke sizes and designs quite reasonably priced if you need. What sort of drawing do you need, that sort of service could be very useful? 1 Link to post Share on other sites More sharing options...
BrushType4 Posted February 24, 2021 Share Posted February 24, 2021 4 hours ago, Blandford1969 said: What sort of drawing do you need, that sort of service could be very useful? Ideally a dxf file from a CAD but understanding that not everyone has access or the skills for CAD, a pen and paper drawing with either scale dimensions or actual dimensions will work. 2 Link to post Share on other sites More sharing options...
RMweb Premium Blandford1969 Posted February 24, 2021 RMweb Premium Share Posted February 24, 2021 3 hours ago, BrushType4 said: Ideally a dxf file from a CAD but understanding that not everyone has access or the skills for CAD, a pen and paper drawing with either scale dimensions or actual dimensions will work. Thanks, will bear that in mind once drawings for West Moors are finished. 1 Link to post Share on other sites More sharing options...
Pete the Elaner Posted February 24, 2021 Share Posted February 24, 2021 I tried cutting them from plastruct strips but my results were so bad I gave up. They all looked crooked & were inconsistent with each other. Bloody awful. Then I tried resin 3d printing & it was a game changer. I can now print the windows I want. They are neat & consistent. The only drawback is that I don't think waving a mouse around feels like modelling to me. There are some photos of my buildings in my layout thread (a link to this is in my signature). Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now