drgj Posted April 2, 2021 Author Share Posted April 2, 2021 (edited) I just read through John's (Brossard) thread on his stove r and noticed he had done the same thing of making a jig for the stepboard holes and drilling through it. He should have the credit for doing it first! Anyway, it worked well. Dave Edited April 2, 2021 by drgj 1 1 Link to post Share on other sites More sharing options...
drgj Posted April 4, 2021 Author Share Posted April 4, 2021 (edited) This is where I am now. I have the body soldered as in previous pics plus the roof cut to length, etc. The roof is a very good fit so I must have got the body nice and square. Here is the picture of the underframe/ floor assembly. I still have to fit the lower steps and various white metal fittings. I will be using Araldite for the latter. I used plain wire between the brake blocks rather than yokes. The centre w iron assembly has the fold up centre bearing for the wheels. I fitted the pin point bearings just to give the axle boxes something to positively fit to. The step boards are on .45mm wire. The wire is fitted in the holes to be flush at the back. It is strong and didn't require bending at the rear as in the instructions. I thought these would get in the way of something. To fit the boards to the wire I put them in place and jammed some card packing between the board and foor edge. Sodering didn't cause the wire to loosen in the sole bar or if it did the card stopped movement. Two holes weren't pefectly level but a slight bend in the wire whist keeping the board horizontal sorted it. They look nice and level from the side. Dave Edited April 4, 2021 by drgj 3 Link to post Share on other sites More sharing options...
drgj Posted April 12, 2021 Author Share Posted April 12, 2021 I have been wondering about the battery regulator (I think that is what it is!). Is this a flat plate with the regulator on and then supported by four angled pieces of wire or two angled pieces of sheet? Thanks Dave Link to post Share on other sites More sharing options...
Ralphrob48 Posted April 12, 2021 Share Posted April 12, 2021 Stove R on E Lancs Railway, photos taken January 2013 of the recently restored vehicle which may be of use to you. 4 2 2 Link to post Share on other sites More sharing options...
drgj Posted April 12, 2021 Author Share Posted April 12, 2021 Thank 1 hour ago, Ralphrob48 said: Stove R on E Lancs Railway, photos taken January 2013 of the recently restored vehicle which may be of use to you. Thanks to ralphrob for the excellent pictures. Link to post Share on other sites More sharing options...
RMweb Premium Roger Sunderland Posted April 13, 2021 RMweb Premium Share Posted April 13, 2021 Hi there I've built the Comet StoveR. It’s a nice kit but still struggles for running quality. I also have a Dapol stove which has festered in a drawer for years as it is pretty much incapable of good running. Whilst looking at alternative chassis I have recently added an Ian McDonald (Mc Geordie of this parish) 6 wheel Palethorpes sausage van to my fleet. Truly a fabulous kit, as indeed are all his kits. The 6 wheel chassis runs superbly through all track formations including reverse curves - so I wondered if I could use a reworked version on the Dapol van. In the end modifications proved relatively straightforward. Hopefully the attached pics will give an idea. the only mod to the Dapol body was to increase the height of the central section to match the ends. These are the 3 trucks that make up the articulated running unit. A continuous step board was added both sides from scrap etch. The component parts of body, articulated trucks and chassis showing how it goes together. Alterations to the sausage van chassis include moving one battery box so they are not opposing and moving the regulator to the opposite side. Guards steps and van end steps were fashioned from brass strip. Fial chassis after painting. Still needs numbering, but it won’t be reusing in a drawer any more. 2 1 3 Link to post Share on other sites More sharing options...
drgj Posted April 14, 2021 Author Share Posted April 14, 2021 I like that a lot. . The battery box supports look good and are those brass nem sockets for couplings? Very neat. I would never have thought of doing that. I have some Parkside nem mounts that I was thinking of using. Dave Link to post Share on other sites More sharing options...
RMweb Gold ianLMS Posted April 14, 2021 RMweb Gold Share Posted April 14, 2021 I built both the comet stove R and the Ian Macdonald Palethorpes kit and agree Ian's chassis is superb!!! Link to post Share on other sites More sharing options...
RMweb Premium Roger Sunderland Posted April 14, 2021 RMweb Premium Share Posted April 14, 2021 1 hour ago, drgj said: I like that a lot. . The battery box supports look good and are those brass nem sockets for couplings? Very neat. I would never have thought of doing that. I have some Parkside nem mounts that I was thinking of using. Dave Thanks Dave. Yes the nem sockets are a fold up item that come in all Ian McDonald’s kits. I can’t stress enough how good his etched kits are, I’ve built several now, well thought out and the best instructions I’ve ever seen. No connection just a very satisfied user. 1 Link to post Share on other sites More sharing options...
brossard Posted April 14, 2021 Share Posted April 14, 2021 I couldn't agree more about Ian's kits. I built his 7mm Palbrick and I was extremely impressed. I'm not going to say it was easy, every kit has it's challenges. I also had to fill in the blanks on the underframe detail. John Link to post Share on other sites More sharing options...
RMweb Gold Asterix2012 Posted April 21, 2021 RMweb Gold Share Posted April 21, 2021 Does Ian have a website? Link to post Share on other sites More sharing options...
brossard Posted April 21, 2021 Share Posted April 21, 2021 4 hours ago, Asterix2012 said: Does Ian have a website? Not as far as I know. He does create threads for his kits on RMweb though, so keep an eye out. John Link to post Share on other sites More sharing options...
RMweb Premium Roger Sunderland Posted April 21, 2021 RMweb Premium Share Posted April 21, 2021 Probably best to PM him. Look up McGeordie in the members list or if you search Palethorpes sausage van he’ll come up. 1 Link to post Share on other sites More sharing options...
drgj Posted June 25, 2021 Author Share Posted June 25, 2021 Have finally finished the stove. I copied the plain sided maroon one from the Paul Bartlett site but painted it in blue. I quite enjoyed building my first full Comet kit but there was a lot more drilling, cutting and filing than I expected. Previously if building a coach I have used brass sides and an rtr coach and just thought it would be nice to build a kit where all is ready made, holes drilled, etc, but this wasn't the case! I started having to force myself to get on withe next fiddly bit. Also the instructions were wrong so Iused the chanelled sole bar instead of plain by mistake. One also feels obliged to solder these kits as well which is a bit of a pain and I only had either a 15w or a massive 65 watt thing with a gigantic tip. The 15w was ok for doing the thin bits like rocking w irons, bake shoes, etc. I had to use the giant iron for the body as the small one didn't have enough oomph. I did not bother soldering the white metal bits as I knew I would melt them! I noticed that the prototype I had chosen had less roof ribs than the Comet plan and for these I used 0.5mm sticky masking tape. I also copied the step configuration- two main ones on each side plus two small lower steps on one side and the long and short on the other. This version didn't have the medium lower step. For paint I used Railmatch black and blue plus some Humbrol to mix the roof colour and for the very light weathering. For weathering I prefer a slightly "dusty" look. To apply the paint I used a Badger airbrush and Iwata compressor. The numbering is pressfix (very fiddly individual numbers) plus some waterslide overhead live wire signs. I couldn't find any stove r transfers. Although I moan I am pleased with the result. Here are some pics 10 5 Link to post Share on other sites More sharing options...
RMweb Gold The Johnster Posted June 27, 2021 RMweb Gold Share Posted June 27, 2021 On 15/03/2021 at 17:00, brossard said: I have a fair number of pin vices. Me too, not neccessarily pin ones... I would rather like a Stove R for Cwmdimbath and will be investigating the Five 79/Chivers fish van chassis as the basis for this. with the choice of Dapol, Comet, or Recreation 3D printed body, but this will be very much a future project; I have too much else to sort out first before embarking on something else... Link to post Share on other sites More sharing options...
Steamport Southport Posted June 27, 2021 Share Posted June 27, 2021 I would just stick to the Comet chassis unless you have very severe curves. If you can get a Pannier around your curves then you won't have any problems with a Stove R. As for the chassis. You've got to be careful with the instructions as they are also for the LNER vans. It is a bit complicated. It's the LNER vans that have the channelled solebar. G in the diagram. For LMS use F. Then use the leftover one as the foot boards. https://www.wizardmodels.ltd/wp-content/uploads/2019/06/um5.pdf Certainly not a beginners kit and it looks good in blue. If you can build that then you won't have any problems with any of the other kits. Jason Link to post Share on other sites More sharing options...
drgj Posted June 28, 2021 Author Share Posted June 28, 2021 (edited) My instructions didn't look like that. I bought the kit on eBay and the instructions definitely said use G for M59. It must have been an old version. When I first realised the mistake I had made I looked back at the instructions and that is what it said. I have seen several others built the wrong way- even the picture on the Wizard models site has a channeled solebar. Here is one posted on this site. Dave Edited June 28, 2021 by drgj 1 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now