Porkscratching Posted August 30, 2019 Share Posted August 30, 2019 Excellent ! ...I reckon the pavements could use a few old newspapers and a bit of general rubbish tho.!! 1 2 Link to post Share on other sites More sharing options...
retiredoperator Posted September 30, 2019 Share Posted September 30, 2019 Hi Westerhamstation. I agree with everyone, but now, after several years, the line has gone and indeed partly built over by the construction of the M25. I don’t know if there are any followers that bother with youtube, but there is an interesting video on the line, with a commentary. Happy Modelling Kev 1 Link to post Share on other sites More sharing options...
RMweb Gold Popular Post westerhamstation Posted September 30, 2019 Author RMweb Gold Popular Post Share Posted September 30, 2019 Another plate girder bridge, this time its a small one that covers the lower level line that runs next to the Acme Engineering Works. Made from cardboard and some plasticard rivet sheet. Some pictures of it in situ. My next big job is to finish off the arches and bridges along the right hand side of the baseboard. All the best Adrian. 29 5 Link to post Share on other sites More sharing options...
RMweb Gold Alister_G Posted September 30, 2019 RMweb Gold Share Posted September 30, 2019 Cracking mate, love all the nooks and crannys, so evocative of the area. Al. 1 1 1 Link to post Share on other sites More sharing options...
Calidore Posted September 30, 2019 Share Posted September 30, 2019 Hi Adrian, fantastically atmospheric and detailed as always. I spend a fair bit of time looking at photos of the Canon Street / Charing Cross lines in the 60s for research, when not on my usual LSWR stuff, and you have the look down to a tee. Thought I’d ask a question which has been occupying my mind, if I may: how was the Grand Vitesse worked (/how is the model worked) without points for locomotive release at the ends? Did the train engine propel back and use the main line points somehow, or was there a pilot? I can’t see how it would have been managed without some awkward propelling moves. Best, Adam 1 1 Link to post Share on other sites More sharing options...
SouthernBlue80s Posted September 30, 2019 Share Posted September 30, 2019 I really like that 1 Link to post Share on other sites More sharing options...
RMweb Premium AdeMoore Posted October 1, 2019 RMweb Premium Share Posted October 1, 2019 8 hours ago, westerhamstation said: Another plate girder bridge, this time its a small one that covers the lower level line that runs next to the Acme Engineering Works. Made from cardboard and some plasticard rivet sheet. Some pictures of it in situ. My next big job is to finish off the arches and bridges along the right hand side of the baseboard. All the best Adrian. Nice work Adrian I need to read through this topic as I have only recently come across it. From the above (I assume it’s 4mm) the plastikard rivet sheet interests me as I have a rather big project rumbling along in the background where I had in mind the Wills girder bridge, but seeing your finished bridge here I think it could work well for me. Is it 0431 in that link? Thanks in advance another Adrian! 1 1 Link to post Share on other sites More sharing options...
Porkscratching Posted October 1, 2019 Share Posted October 1, 2019 I've doubtless said this before but...This layout is absolutely spot on..I used to go through London bridge, Waterloo East (to and from) Charing X during the 80s and I can picture a section that is a dead ringer for this, obviously it was all 3rd rail EMUs in my day.. but it's uncanny how right he's got the look and feel of the place...just outstanding! 1 3 1 Link to post Share on other sites More sharing options...
RMweb Gold Oldddudders Posted October 1, 2019 RMweb Gold Share Posted October 1, 2019 2 hours ago, Porkscratching said: I've doubtless said this before but...This layout is absolutely spot on..I used to go through London bridge, Waterloo East (to and from) Charing X during the 80s and I can picture a section that is a dead ringer for this, obviously it was all 3rd rail EMUs in my day.. but it's uncanny how right he's got the look and feel of the place...just outstanding! The feel of the place is indeed what has been captured. Like you many years of commuting through there, plus 40 years ago occasionally finding myself as SM at Cannon St, Charing Cross and Holborn Viaduct, have been brought back by Adrian's atmospheric representation. 3 1 Link to post Share on other sites More sharing options...
malcolmcelyn Posted October 1, 2019 Share Posted October 1, 2019 (edited) 2 hours ago, Oldddudders said: The feel of the place is indeed what has been captured. Like you many years of commuting through there, plus 40 years ago occasionally finding myself as SM at Cannon St, Charing Cross and Holborn Viaduct, have been brought back by Adrian's atmospheric representation. I have an idea (on the back burner whilst I dabble in 7mm scale) of a layout based on Borough Market Junction. It would need just this sort of construction and atmosphere. Well done Westerhamstation on creating a believable slice of London. Edited October 1, 2019 by malcolmcelyn 1 1 Link to post Share on other sites More sharing options...
RMweb Gold westerhamstation Posted October 1, 2019 Author RMweb Gold Share Posted October 1, 2019 18 hours ago, Calidore said: Hi Adrian, fantastically atmospheric and detailed as always. I spend a fair bit of time looking at photos of the Canon Street / Charing Cross lines in the 60s for research, when not on my usual LSWR stuff, and you have the look down to a tee. Thought I’d ask a question which has been occupying my mind, if I may: how was the Grand Vitesse worked (/how is the model worked) without points for locomotive release at the ends? Did the train engine propel back and use the main line points somehow, or was there a pilot? I can’t see how it would have been managed without some awkward propelling moves. Best, Adam Hi Adam, in answer to your question I must confess that I have no real idea on the of how the Grand Vitesse was worked in real life, but i am sure that others on here will be able to help throw some light on it. I have sent you a pm of a magaazine article about the Grand Vitesse which might help. I cant post it on here as it might infringe some copyright. All the best Adrian. 1 1 1 Link to post Share on other sites More sharing options...
RMweb Gold westerhamstation Posted October 1, 2019 Author RMweb Gold Share Posted October 1, 2019 12 hours ago, AdeMoore said: Nice work Adrian I need to read through this topic as I have only recently come across it. From the above (I assume it’s 4mm) the plastikard rivet sheet interests me as I have a rather big project rumbling along in the background where I had in mind the Wills girder bridge, but seeing your finished bridge here I think it could work well for me. Is it 0431 in that link? Thanks in advance another Adrian! Hi Ade, yes the Slaters 0431 is the one. if you have loads of rivets you might like to try the Acme Rocket Riviter Mk1, page 85 about two thirds the way down describes its use. All the best another Adrian. 1 1 Link to post Share on other sites More sharing options...
RMweb Premium AdeMoore Posted October 1, 2019 RMweb Premium Share Posted October 1, 2019 Thanks for the tip Adrian. Couldn't dig out the Acme Rocket Riveter unfortunately. Google had no luck either. Cheers Ade 1 Link to post Share on other sites More sharing options...
RMweb Gold Alister_G Posted October 1, 2019 RMweb Gold Share Posted October 1, 2019 47 minutes ago, AdeMoore said: Couldn't dig out the Acme Rocket Riveter unfortunately. Hi Ade, follow this link mate: https://www.rmweb.co.uk/community/index.php?/topic/64587-westerham-ewer-st-another-bridge/page/85/&tab=comments#comment-2624108 Al. 1 2 Link to post Share on other sites More sharing options...
RMweb Gold westerhamstation Posted October 2, 2019 Author RMweb Gold Share Posted October 2, 2019 Hi Al, thanks for posting the link to the Acme Rocket Riveter mk1, pictures of the Mk 2 undergoing trials at the Acme proving grounds. Thank you all for your kind comments on capturing the atmosphere of that area of South London and it is jogging your memories of times past. When working on it I can seem to smell and taste the area which i hope dosn't sound to far fetched. All the best Adrian. 2 1 4 1 Link to post Share on other sites More sharing options...
RMweb Gold Alister_G Posted October 2, 2019 RMweb Gold Share Posted October 2, 2019 (edited) 1 hour ago, westerhamstation said: When working on it I can seem to smell and taste the area You need to get your central heating checked... It's that coal gas that does it Al. Edited October 2, 2019 by Alister_G 6 Link to post Share on other sites More sharing options...
RMweb Gold lezz01 Posted October 2, 2019 RMweb Gold Share Posted October 2, 2019 Hi Adrian. Loving the Acme Rocket Riveter. Great idea! Now where is that broken clock?! HONEY!! Where did you put your grandad's old clock??? I'm going to ......err.......fix it....um...well sort of fix it....well use it...err..um..part of it anyway .........LOL Regards Lez. 1 2 Link to post Share on other sites More sharing options...
RMweb Premium AdeMoore Posted October 2, 2019 RMweb Premium Share Posted October 2, 2019 3 hours ago, westerhamstation said: Hi Al, thanks for posting the link to the Acme Rocket Riveter mk1, pictures of the Mk 2 undergoing trials at the Acme proving grounds. Ahhhhhhhhhhhhh! Okay ok fik or what! thought to the Acme Rocket Riveter didn’t have a slaters ring about it! But off I went looking for page 85! Doh!!! Thanks Al for the link and guidance to a naive modeller. Cheers 4 Link to post Share on other sites More sharing options...
Stephenwolsten Posted October 5, 2019 Share Posted October 5, 2019 I've just discovered you! Fantastic to see the Bazzing Around article (which I have kept all these years) come to life in such an inspiring way. 1 Link to post Share on other sites More sharing options...
Mrkirtley800 Posted October 5, 2019 Share Posted October 5, 2019 This is one of the most atmospheric models on RMW. I look for it every time I go on line. It all looks so natural. Superb Derek 1 4 1 Link to post Share on other sites More sharing options...
RMweb Gold westerhamstation Posted October 6, 2019 Author RMweb Gold Share Posted October 6, 2019 Hi Derek, thank you, and I hope that you are on the mend now. All the best Adrian. 1 1 Link to post Share on other sites More sharing options...
RMweb Gold lezz01 Posted October 6, 2019 RMweb Gold Share Posted October 6, 2019 Good to see you posting again Derek mate. Hope your properly on the mend. Regards Lez. 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Popular Post westerhamstation Posted November 20, 2019 Author RMweb Gold Popular Post Share Posted November 20, 2019 This is where I should have started building the layout, not one of the last bits. Space to work in this corner is very tight, to get to it I have to remove a couple of small units, crawl underneath the baseboard then try and squeeze between the wall and the baseboard to finally appear completely knackered and dusty the otherside having left any tools I might need just out of reach on the otherside of the baseboard, thus having to repeat the process in reverse. I must stop eating pork pies as I think they are making the small gap even smaller. Now I am in position to show you whats happening, that's if I stop breathing and hold my stomach in. A viaduct wall will run across the back at high level, replicating the original with a curved top plate girder bridge, the baseboard has been widened to accomdate a small section of double track just to make the bridge and track look wider at this point. The track to Westerham and Brasted runs underneath here. I hope the pictures show what is happing and that Mrs w Station can pull me out of this gap in time for tea. All the best Adrian. 20 Link to post Share on other sites More sharing options...
RMweb Gold ChrisN Posted November 20, 2019 RMweb Gold Share Posted November 20, 2019 It is a good job you are young and fit! If it is too tight to get out you will have to do what Winnie-the-Pooh did, and wait until you are thin. It is coming on well. I doubt it would have worked if you had done it first. 3 Link to post Share on other sites More sharing options...
RMweb Gold Alister_G Posted November 20, 2019 RMweb Gold Share Posted November 20, 2019 I was thinking it's a good job you started this before Christmas, and not after... Nice work, mate, well squeezed. Al. 3 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now