Edwardian Posted November 23, 2018 Share Posted November 23, 2018 (edited) Very good information for the technically-inclined here, which shows the second ‘power train’ and cooling arrangement very clearly. https://www.wolseleycarclubnz.co.nz/railway.html Ironically, the photograph of 3171 used on the site shows it as it was with the Napier engine installed. However, so did Wolseley's own advertising! The drawings used on the site come from an article in The Tramway and Railway World, 12 May 1904*. A plan view in the article shows the cooling pipes (I am going to call them pipes!) on the clerestory roof. These are the only drawings that I have seen that show this feature, though it is evident in all the photographs of the cars with the Wolseley engines on board. The Wolseley engine is fairly well documented in drawings and photographs. Not so the Napier. if anyone comes up with an illustration of that, I'll be pleased and surprised in equal measure. *EDIT: These drawings also reproduced in Motor Traction, 15 September 1906. Edited November 23, 2018 by Edwardian 6 Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted November 23, 2018 Author RMweb Premium Share Posted November 23, 2018 So when was the number of doors changed on the side? Very early on? Many thanks Richard There was a refit in 1908 to enlarge the 'gangway' to a 'vestibule' with double doors, this was at the cost of a pair of seats and reglazing the passenger saloon from six 'long' windows to five and 'a half'. Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted November 23, 2018 Author RMweb Premium Share Posted November 23, 2018 To be fair, I suspect 3 of the 4 pictures I posted may be of the same model (that on Runswick Bay), The Marske layout is apparently set c.1910-1920, so the double door condition is a fit for that timeframe. I gather Runswick Bay has passed into private hands; a pity from my point of view, as I never managed to see it in the flesh. The first three are my photos of Robin Taylor's scratchbuilt (7mm) model, shown on Runswick Bay (x1) and Ravensbeck (x2) courtesy of the Keighley Model Railway Club who helped arrange the 'photoshoots'. Robin built this while the autocar was still relatively unknown. The Medley Models kit was the first kit, then in 2009 my father and I measured up the autocar for Allen Doherty at Worsley Works, who has done the brass etches in several scales. 1 Link to post Share on other sites More sharing options...
Edwardian Posted November 23, 2018 Share Posted November 23, 2018 The first three are my photos of Robin Taylor's scratchbuilt (7mm) model, shown on Runswick Bay (x1) and Ravensbeck (x2) courtesy of the Keighley Model Railway Club who helped arrange the 'photoshoots'. Robin built this while the autocar was still relatively unknown. The Medley Models kit was the first kit, then in 2009 my father and I measured up the autocar for Allen Doherty at Worsley Works, who has done the brass etches in several scales. Apologies for the appropriation! At least the 4th photo was mine! There was a refit in 1908 to enlarge the 'gangway' to a 'vestibule' with double doors, this was at the cost of a pair of seats and reglazing the passenger saloon from six 'long' windows to five and 'a half'. Apparently the move to the Cawood branch was summer 1908 and the change in doors was subsequent to that. I read somewhere 1909-10, but certainly after they left the Scarborough-Filey service. Would be happy for any corrections/more precise info, however. 1 Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted November 25, 2018 Author RMweb Premium Share Posted November 25, 2018 No problem with you using the photos, I took them for use in our publicity. According to the plan below, taken from an original NER plan book, courtesy Mike Grocock, the revised design was dated December 1908, I suppose depending how long the refit lasted it might have been 1909 before one/both was back in traffic. But the original plan is dated 1904, which suggests to me the date on the plan is entry into service/being signed off as fit to run rather than registration of a plan/design. Does anyone know which date would be used? 3 Link to post Share on other sites More sharing options...
Edwardian Posted November 26, 2018 Share Posted November 26, 2018 No problem with you using the photos, I took them for use in our publicity. According to the plan below, taken from an original NER plan book, courtesy Mike Grocock, the revised design was dated December 1908, I suppose depending how long the refit lasted it might have been 1909 before one/both was back in traffic. But the original plan is dated 1904, which suggests to me the date on the plan is entry into service/being signed off as fit to run rather than registration of a plan/design. Does anyone know which date would be used? Plan 1908-31© MG.jpg That is helpful, thanks. I read somewhere that the cars were transferred to the Cawood branch in the summer of 1908, so it seems that some time spent there revealed to the management the need to make provision for luggage compartments. Whether the work was completed before the end of that year or not, it was there or thereabouts. Odd that the residents of Cawood would have more luggage than those travelling to and from Scarborough! 1 Link to post Share on other sites More sharing options...
Nearholmer Posted November 26, 2018 Share Posted November 26, 2018 Without a luggage area, it must have been a blasted nuisance for people with ‘dogs, bicycles, and perambulators’ ........ just like all too many modern trains, in fact! Link to post Share on other sites More sharing options...
Edwardian Posted November 26, 2018 Share Posted November 26, 2018 Without a luggage area, it must have been a blasted nuisance for people with ‘dogs, bicycles, and perambulators’ ........ just like all too many modern trains, in fact! plus ça change .... 1 Link to post Share on other sites More sharing options...
richard i Posted November 27, 2018 Share Posted November 27, 2018 That is helpful, thanks. I read somewhere that the cars were transferred to the Cawood branch in the summer of 1908, so it seems that some time spent there revealed to the management the need to make provision for luggage compartments. Whether the work was completed before the end of that year or not, it was there or thereabouts. Odd that the residents of Cawood would have more luggage than those travelling to and from Scarborough! Day trippers to the seaside? Link to post Share on other sites More sharing options...
Edwardian Posted November 27, 2018 Share Posted November 27, 2018 Day trippers to the seaside? Or possibly mass migration from Selby! Link to post Share on other sites More sharing options...
richard i Posted November 27, 2018 Share Posted November 27, 2018 Or possibly mass migration from Selby!Without any stuff! And then I remembered back when I were a lad up north we were lucky to have cold cardboard to live in. Had to wake three hours before going to bed and ate cold gravel. ...,but we were happy. Link to post Share on other sites More sharing options...
runs as required Posted November 28, 2018 Share Posted November 28, 2018 (edited) I've just realised that 'Hastings' unit style diesel-electric engine compartment is very roomy for the NER's original petrol-electric equipment - as compared to the contemporary 1900s Tilling-Stevens road motor bus which had its petrol engine under the bonnet and the electrical gear underslung. The Wiki T-S site is interesting about the decline of the petrol-electric system (until its revival in recent hybrid electric vehicles). It was originally sold as an easy transfer to driving a horseless vehicle, bypassing the need to master clutch and crash gearbox. But the War Office would not approve the T-S system for use at the Front in WW I because of its electrical gear being vulnerable to mud compared to the use of a clutch and crash gearbox. By the end of the war there were a lot army drivers experienced in driving the flood of ex WD vehicles released onto the Civvy streets. Petrol-electric traction for road traction was quite literally overtaken by the more sprightly mechanical systems and by the mid 1930s T-S had adopted clutch and gearbox transission for petrol and diesel . T-S were were also into trolley buses in the 1930s but, in retrospect, seem to have missed a trick in offering a vehicle with an auxillary engine for use beyond the wires - as Renault did in France. dh Edited November 28, 2018 by runs as required 1 Link to post Share on other sites More sharing options...
Nearholmer Posted November 28, 2018 Share Posted November 28, 2018 (edited) The other 'big-issues' for PE, as opposed to PM, in light vehicles, railcars, carries, cars, lorries, busses etc at the time were two-fold: - weight, in that once gearboxes and, just as importantly clutches, advanced far enough, the E part of the PE was heavier than the mechanical transmission; and, - it took a few years to get the engine controls integrated with the dynamo controls in a way that allowed the most to be got out of the engines when in the hands of a non-technical driver. In many cases early PE seem to have been operated with the engine running at a practically constant speed, which is fuel-efficient, but not necessarily power/weight efficient. There were, of course, PE 2ft gauge locos used by the British Army during WW1, the French had Crochat PEs in both SG and 2ft, and the Austro-Hungarian Army had PE road/rail tractors and trailers designed by Porsche, which were the progenitors of the Austrian (GEBUS) DEs of the 1920s and onwards that ultimately led ultimately to the DE versions of the Fliegender Hamburger. During the pre-WW1 period, there was also another PE bus rival to the T-S design. T-S was a DC transmission, but the Durtnall rival had a 3-phase transmission, which he had also applied to a car I think. Its all very, very interesting, but to get your head around the history of PE/DE its necessary to look at US, British and European designs, spanning rail, road, and shipping, because the top engineers in the field (a) knew what was going on across the world, and (b) worked across all modes. Edited November 28, 2018 by Nearholmer 1 1 Link to post Share on other sites More sharing options...
RMweb Premium PhilJ W Posted November 28, 2018 RMweb Premium Share Posted November 28, 2018 Mechanical transmissions were not too far behind PE systems. The usual mechanical (semi-automatic) transmission used in most British DMU's was developed for WW1 tanks. Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted December 7, 2018 Author RMweb Premium Share Posted December 7, 2018 Changing the subject, I am very proud to announce that the autocar's restoration has won the Manisty award. This is the Heritage Railway Association’s most prestigious award, awarded by the Board of the HRA on an occasional basis for an exceptional and outstanding contribution to railway preservation. It's a much appreciated recognition of the skills and efforts of our volunteers. 4 Link to post Share on other sites More sharing options...
RMweb Premium Dava Posted December 7, 2018 RMweb Premium Share Posted December 7, 2018 Richly deserved award as an "exceptional and outstanding contribution to railway preservation". Dava 1 1 Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted January 28, 2019 Author RMweb Premium Share Posted January 28, 2019 And now some running dates... Basically, Wednesdays Easter - July and in September together with some extra days that first week in September. And the first three Sundays in November. https://www.embsayboltonabbeyrailway.org.uk/timetable/timetable News on visits elsewhere when I can give you the details. Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted February 19, 2019 Author RMweb Premium Share Posted February 19, 2019 Two photos of the Awards presentation - I can now reveal we also won the Modern Traction Award, courtesy Rail Express. Photo courtesy Robin Jones of Heritage Railway magazine. (And thanks to the un-named person who took this on one of our member's phones). 3 1 Link to post Share on other sites More sharing options...
RMweb Gold Bucoops Posted February 20, 2019 RMweb Gold Share Posted February 20, 2019 So a 1903 autocar won a modern traction award? Love it Well done to all involved. 3 Link to post Share on other sites More sharing options...
RMweb Premium Dava Posted February 20, 2019 RMweb Premium Share Posted February 20, 2019 9 hours ago, Bucoops said: So a 1903 autocar won a modern traction award? Love it Well done to all involved. If you look at the parts list, there is quite a lot of modern traction in there, the chassis & power unit date from 2013/4. 2 Link to post Share on other sites More sharing options...
RMweb Gold Bucoops Posted February 20, 2019 RMweb Gold Share Posted February 20, 2019 29 minutes ago, Dava said: If you look at the parts list, there is quite a lot of modern traction in there, the chassis & power unit date from 2013/4. Oh I know but it's still amusing 4 Link to post Share on other sites More sharing options...
RMweb Premium Compound2632 Posted February 22, 2019 RMweb Premium Share Posted February 22, 2019 On 20/02/2019 at 08:19, Bucoops said: So a 1903 autocar won a modern traction award? Love it Well done to all involved. That's why I model 1902. 2 Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted February 22, 2019 Author RMweb Premium Share Posted February 22, 2019 Last November, our engineer queried whether we have a new record as the only train to be featured in both Modern Railways and Heritage Railway at the same time! 3 2 Link to post Share on other sites More sharing options...
MarkC Posted April 8, 2019 Share Posted April 8, 2019 I must get to Embsay and see this superb vehicle for myself very soon. In the meantime, a question, if I may? I have seen the NER livery described as "Poppy Red & Ivory", but has anyone any recommendations for suitable proprietary paints which would suit, please? I've got a set of 4mm Worsley Works etches in my roundtuit pile, and would like to get busy with them ere long... Thank you in advance. 1 Link to post Share on other sites More sharing options...
RMweb Premium The White Rabbit Posted April 10, 2019 Author RMweb Premium Share Posted April 10, 2019 We're running every week on Wednesdays after Easter until the summer school holidays. Can anyone help Mark with the colours? I know several people were building or have built 4mm models, though none of the restoration team or I are amongst their numbers (yet!) we've been too busy with the full size article. A couple of us have threatened to build models afterwards, once the active work on improvements and final fettling on both vehicles is done. That's probably going to be 'ere too long'... 1 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now