RMweb Premium DLT Posted July 10, 2021 RMweb Premium Share Posted July 10, 2021 Aha, yes I can see how that works now, devilishly clever! Many thanks, Dave. Link to post Share on other sites More sharing options...
dpgibbons Posted July 10, 2021 Share Posted July 10, 2021 DCC Concepts now have a range of drive-off loco cassettes here Link to post Share on other sites More sharing options...
RMweb Gold zr2498 Posted July 11, 2021 Author RMweb Gold Share Posted July 11, 2021 5 hours ago, dpgibbons said: DCC Concepts now have a range of drive-off loco cassettes here Yes, they have been around for quite a while but for some reason with the upgraded design (improved foam = EVA), the price has doubled. It will be interesting to see what price the the new Peco PT-60 and PT-61 come in at and just how many can be coupled together whilst maintaining rigidity. And of course if the new design would fit into the shoe boxes as explained above. Link to post Share on other sites More sharing options...
CUCKOO LINE Posted September 20, 2021 Share Posted September 20, 2021 On 10/07/2021 at 11:34, zr2498 said: I will add to the job list as a fair bit of work needed to explain all. The brass strips are basically a spring loaded lever arm. At one end it is pushed up and let down by a pin which protrudes through the underside of the cassette. At the other end is an arm set at 90 gegrees with a rubber buffer fitted over wire. As the cassette is loaded onto the telescopic deck the pin pushes to lever up = down at the buffer end so that stock can run through the end of the cassette. As soon as the cassette is lifted the opposite happens and the buffer comes up. This is set at buffer height of the rolling stock and prevents the unwanted unloading out of the ends. The same could be achieved by pieces of foam but wanted an auto system (to see what could be achieved), and one less job to do when changing stock. Dave Interested in "How did you construct the tubes ? " I need to create something similar. Thanks Link to post Share on other sites More sharing options...
RMweb Gold zr2498 Posted September 20, 2021 Author RMweb Gold Share Posted September 20, 2021 Just got this notification. I'll send some info tomorrow, but just confirming you would like details base, walls and lids of the cassettes? Dave Link to post Share on other sites More sharing options...
RMweb Gold zr2498 Posted September 21, 2021 Author RMweb Gold Share Posted September 21, 2021 (edited) On 20/09/2021 at 22:58, zr2498 said: Just got this notification. I'll send some info tomorrow, but just confirming you would like details base, walls and lids of the cassettes? Dave Here is a close up of the end of a cassette to give an idea of the construction. You will see a length of 9mm MDF forming the base of the cassette. This is painted with an outdoor wood paint to ensure it is waterproof and stable. Width is 55m, and I have made 15 at 1700mm length and 15 at 1400mm length. This is bolted to aluminium angle 1 in x 3/4 in x 1/16 in (1" is on the vertical). The walls of the cassette are Perspex, 2mm thickness and 65mm high. The strips were cut from sheet using a clamped (long) straight edge for a guide line and many passes with an Olfa cutter. The track is screwed to the MDF with the ends sitting on the copper clad, and being finely adjustable about a pivot point to finalise alignment. Here are some pictures of materials used. Straps and handles were also made. Bolted to the inside of the perspex and fixed across the top via screwed rod. Removable lids have been added to the tops of the cassettes. In 3 pieces, centre and either side of the handles. The lids clip onto the top by means of plastic angle sections which are attached to the lid via strong 2 sided tape. Notes: I preferred to have track rather than the aluminium profile for current pick up. The aluminium can become corroded causing poor power transfer and it also allowed the fine alignment needed for system I was using. The other advantage is that isolation is not needed for the handles (to prevent shock). All fixings of the cassette are bolted, so if I was crazy enough they could be totally dismantled. Thin plastic washers are used wherever a fixing comes into contact with the perspex (to prevent potential cracking). Holes for fixing over such a long length need to have some clearance to allow for differential expansion. Precise alignment of the cassettees to track is done by dowels underneath the cassette, with the cassette able to float in the length direction (again to allow expansion). Fixing dowels. Hopefully this gives enough of a flavour for how it was done. If more details are needed I will dig out the info. Dave Edited April 1, 2023 by zr2498 Replacing photos 1 Link to post Share on other sites More sharing options...
CUCKOO LINE Posted September 21, 2021 Share Posted September 21, 2021 Brilliant, that is very useful and interesting, should give me a good basis for some cassettes. Many thanks for the explanation etc. 1 Link to post Share on other sites More sharing options...
cliff park Posted September 21, 2021 Share Posted September 21, 2021 Just in case it helps, MDF will reliably take a thread. Obviously not for heavy loads, nor for repeated screwing in and out, but for an assembly like this it would be better than woodscrews Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now