RJdeVries

A month had passed again but I've not been sitting at idle. After re-instating the garden railway last week I managed to have a proper first running session with the Class 101. IMG_20230421_104121_1 by Robbert Jan., on Flickr IMG_20230421_104815 by Robbert Jan., on Flickr Although it was quite windy today I managed to make a video of the first departure out of the station. (to be) Besides the Class 101 being able to run as a solo Dmu it also sports a whole range of light functons that can be seen below. Class 101 lights and cab console by Robbert Jan., on Flickr Now it is finally at a stage that I can tackle the interior as I do not need to alter anything anymore, and ofcourse the corridor connection and a pair of exhaust pipes are in order. Hope you enjoy! Regards, Robbert Jan.

Last week I recieved a package from Slaters plasticcard and that included a set of vacuum pipes for the bufferbeams in between both DMBS and DTCL Vacuum hoses attached by Robbert Jan., on Flickr Vacuum hoses attached by Robbert Jan., on Flickr And all coupled up it looks like this, almost there, the real test will be on the actual railway and through points and curves. Vacuum hoses attached by Robbert Jan., on Flickr Vacuum hoses attached by Robbert Jan., on Flickr Hope you enjoy, Regards, Robbert Jan.

I've bought the motor and gears at a German company called Lemo Solar. The motor I've bought has a 6:1 ratio that suits the Class 101 perfectly. Regards, Robbert Jan.

It's been a while but I havn't forgotten about this forum, I just can't be everywhere at the same time and posting from a mobile device is a real pain to do. Since the last time I managed to fit all the glass so the unit is watertight at last. This meant that I could proceed with the plans I had for the inside of the DMBS and DTCL, lots of lights that can be switched on or off through the Dcc decoder. IMG_20221102_170921 by Robbert Jan., on Flickr IMG_20221102_124225 by Robbert Jan., on Flickr Lots of wires, very tiny wires and an assortment of small led's where used to illuminate the cab ends, markers, headcode, taillamps (and seperate lantern), the lot. Below is a short clip of the DTCL and it's functions. For some added realism I've added a small plug underneith the bufferbeam that will allow for a separate lamp to be plugged in. IMG_20230226_163643 by Robbert Jan., on Flickr And speaking of plugs, MU plugs to be precise. Class 101 MU cables pt2 by Robbert Jan., on Flickr Class 101 MU cables pt2 by Robbert Jan., on Flickr These MU plugs are functional as in they are there to take the track power from one carriage to the other making sure the decoder doesn't run out of juice. A very small pcb plug is used on either end with the actual white metal castings being converted in to plugs and sockets, this way it looks almost factory. Below is a picture of the connectors used, 1.27mm is the distance between pins. Class 101 MU cables pt2 by Robbert Jan., on Flickr And last but certainly not least, I made a huge modification to the power bogie as I wanted to do away with the motor standing up into the guards compartiment. Compensated powered wheelset by Robbert Jan., on Flickr A complete drive mechanism contained within the power bogie using a pair of small gear reduction electric motors and a set of brass and acetate gears. Compensated powered wheelset by Robbert Jan., on Flickr Above is seen the compensated wheelset with the motor attached to the actual brass frame that comes with the kit, it runs sweet as a nut, even on Dcc after a lot of tweaking of the settings on the decoder. So basically this in the now, I'm currently sorting out the wiring and placement of the decoder plug pcb, it will live in the guards compartment but just underneith the window line and that means I can camouflage it with some random items like packages, maybe a bicycle and ofcourse a guard. Hope you enjoy, Regards, Robbert Jan.

@Fishplate It's a very good looking model, with a lot of etched parts and a nice finish. These models as "ready made" are not cheap at a 50€ but mine was damaged with a broken rear wheel that is was reduced to 20€, a drop of adhesive solved the issue. @figworthy They do seem to have some kind of similiar background, I've never heard of the verhicle shown but a "Pelican" would also be a nice conversation piece on a layout. Regards, Robbert Jan.

It again has been while, not that I've not been up to anything :) My latest purchase has been signed off and has joined the fleet. She will be running as number 7, as it's the 7th loco purchased. A custom set of nameplates is being produced as we speak. Kerr Stuard Victory weathered by Robbert Jan., on Flickr Kerr Stuard Victory weathered by Robbert Jan., on Flickr Got the Kerr Stuard "Victory" through Rails and it arrived just 2 weeks later, not to bad considering it sometimes takes a month to get a parcel across the channel. Next on the agenda was weathering a set of 3 Accurascale Mdo's which also where sent from Rails in the same parcel. IMG_20230108_193242 by Robbert Jan., on Flickr The first steps are the same for any rolling stock I tackle, a wash with either black or very dark grey enamels (revell 6, 8 or 9) Followed by Mig/Ammo Acrylic rust tones from set 7106 consisting of 6 very usefull paints for this kind of weathering. IMG_20230108_193229 by Robbert Jan., on Flickr After the initial weathering I recieved a few comments saying that I should enhance the flaps on the inside, these are not visible nor modelled so I did an outline in paint and made the best of it. IMG_20230115_151333 by Robbert Jan., on Flickr IMG_20230116_202055 by Robbert Jan., on Flickr I've also been working on finishing the headstock, which is finally secured in place and weathered up, ready for some fine detailing. The engine shed was a good weeks work, making sure all the small details where done and ready to be glued in place, even the roof is done. IMG_20230120_135446 by Robbert Jan., on Flickr IMG_20230120_195557 by Robbert Jan., on Flickr The inside of the shed is now a very gloomy place, someone commented that he never felt the urge to mop a floor so badly, but luckily those cleaning items are hidden. IMG_20230120_195606 by Robbert Jan., on Flickr Most of the little bits, workbench, cabinet etc are by Modelu, the barrels are a ready made Artitec product, the drill press is something out of the parts box. Another little ready made gem by Artitec is this Bischoff Polytrack, basically a JCB-esq machine from Germany, it took my fancy and with it being discounted it now lives on the Colliery. Artitec Bischoff Polytrac by Robbert Jan., on Flickr What is next, more weathering, the Cornish Engine needs to fixed in place and so much more. Hope you enjoy! Regards, Robbert Jan.

Thanks Tom, Steve and Vecchio for commenting 👍 The first show is a fact, and it has been a blast, the reactions where positive and people where really interrested in the techniques used. The R&J Colliery by Robbert Jan., on Flickr The layout is now also sitting pretty on her own feet with a nice dark curtain hiding most of her underbits. IMG_20221112_153014 by Robbert Jan., on Flickr All of the stock behaved very well, cleaning the track en locomotives has not disapointed as only one loco didn't make the grade being that the pickups where not up to snuff. I was particularly pleased with the 0-4-0 sentinel "Hendrik" (after my late grandfather) which runs so silky smooth across pointwork with just 2 small tantalum capacitors installed (and a lot of extra lead weights) IMG_20221112_153111 by Robbert Jan., on Flickr And after the show ends it's time to sum up what needs attention, first off the flap on the side where I can insert the coal shutes, it's to small and the lip that prevents stock from coming of the layout prevents me from cleaning any loose coal, so it had to be changed. IMG_20221113_213631 by Robbert Jan., on Flickr A nice new "catflap" on the side, which conveniently also doubles as a passage for additional wagons on to a new extended siding 😃 IMG_20221114_142439 by Robbert Jan., on Flickr IMG_20221114_142559 by Robbert Jan., on Flickr It's just clamped in place, no fysical connection, no power as it's for wagons only. Now I can at least run a train of 4 wagons instead of just 2, happy days. Regards, Robbert Jan.

A little update, Lots has been done to the layout, but most noticably is the addition of autumn colored shrubs and bushes to create that autumn vibe. Autumn has arrived by Robbert Jan., on Flickr IMG_20221108_171000 by Robbert Jan., on Flickr Autumn has arrived by Robbert Jan., on Flickr A very large undertaking was replacing the card roadsurface covering the magnorail track, it has been troublesome at times and finally I made the call to replace it with a suitable thickness of plasticcard, 0,25mm IMG_20221031_124811 by Robbert Jan., on Flickr The road taken up and the magnorail exposed, the chain is removed. The biggest hurdle was the bridge as this is a single sheet of plasticcard, meaning that I needed to do some surgery to be able to slide it in. IMG_20221031_124817 by Robbert Jan., on Flickr But eventually a clean white road surface was layed and the sections where glued together to create smoother seams. IMG_20221031_193414 by Robbert Jan., on Flickr On the rear of the layout sits the motor unit that drives the chain, it is also covered with plasticcard but that would have left me with no way to insert the chain. IMG_20221031_193512 by Robbert Jan., on Flickr So a little hatch was made up using a pair of hinges from a sigarbox. Another upgrade was installed at the headgear and it's drive and tail pulley. These where plastic and kind of nasty so I made a new pair out of scrap brass from my dads stash, a bit of turning on the lathe and the finishing work was done on the milling machine. IMG_20221029_190906 by Robbert Jan., on Flickr These don't wobble all over the place anymore. I'm currently preparing for the first "trail" show next saturday to see how the layout is recieved, and to give it a good shake down test, hoping to find no issues. Regards, Robbert Jan.

The last few days have been spent wiring the first of many lights. I'm using a led panel to generate the different ambient colors, the blue is merely for demonstration purposes. IMG_20221020_194927 by Robbert Jan., on Flickr IMG_20221019_162039 by Robbert Jan., on Flickr Underneith the layout I've mounted the digikeijs dr4018 switching decoders that control the lights and give them their unique startup sequence, like fluorecents and sodium lights. Up top I've been working on a few small projects such as a pair of explosives wagons, a small forklift and I managed to finally obtain a driver for my narrow gauge locomotive. IMG_20221023_165255 by Robbert Jan., on Flickr On the other end the screening and loading facility has been fitted permanently so the landscaping around it can be finished at last A busy afternoon at the Colliery. by Robbert Jan., on Flickr The headstock finally has a pair of realistic sheaves courtesy of MIB Models (Alan) IMG_20221027_122851 by Robbert Jan., on Flickr IMG_20221027_122837 by Robbert Jan., on Flickr I've fitted a brass bushing and some plasticcard detailing to it, its not done and it will be painted etc, but for now I'm pretty chuffed. Regards, Robbert Jan.

Thanks Mikkel, I have indeed used the engine shed as a view blocker towards the curve out of the layout, on the other end the loading facility has a similair job but it also disguises the 180 degree turntable for the magnorail system. All of the other buildings are fully scatchbuild semi relief and they make for an interresting arrangement with the mayority of the small railyard in front. Both grounded van body's also take away a direct view, but can be viewed through as the doors are open on both sides. I'm keeping my fingers crossed on how the layout will be recieved, and how the technical side of things holds up to a days running. Meanwhile I've been working on more little and larger things, mainly adding further weathering to the buildings and the cars on the layout. (photos are not in order of time taken) IMG_20221017_193742 by Robbert Jan., on Flickr IMG_20221017_192845 by Robbert Jan., on Flickr I've washed the cars with a thinned revell 9 (dark grey) to enhance the details and make them a bit more grubby, some of them atleast. I still don't get why the transit had to be white.... I've also added lights underneith the loading facility, just so one can see the action as it is quite dark under there, even when the layout is fully illuminated. IMG_20221014_170632 by Robbert Jan., on Flickr IMG_20221014_170813 by Robbert Jan., on Flickr IMG_20221014_170823 by Robbert Jan., on Flickr The led's are wired up in groups and soldered to a small pcb with 1,2k Ohm resistors. A little side project I've completed is a cleaning wagon on an old tanker chassis. It's loosely based on the system underneith a Roco clean wagon but ive left a gap in the middle of the pad (trackrubber sections) to any details in the center of the track won't be destroyed. IMG_20221015_192816 by Robbert Jan., on Flickr IMG_20221015_192836 by Robbert Jan., on Flickr IMG_20221015_200026 by Robbert Jan., on Flickr It's not designed to be pulled by an engine but rather as a manual cleaning device. It however keeps me from destroying details in and around the trackwork as it works as a guide, it has already been proven usefull. Regards, Robbert Jan.

Thank you very much Jamie, It has been quite the journey these few years and with lack of interest mainly due to there not being any exhibitions in the Netherlands. But with the whole circus alive again the first show is isn't very far away now so a lot of catching up is in order. I do hope it is well received 👍🏻 Regards, Robbert Jan.

This will be a bit of a time warp, a good 2 years has passed and although progress has been slow I've made some substantial effort; I'm just going to post the pictures from last week as the difference with the one's in my last posting is enormous! IMG_20221014_192335 by Robbert Jan., on Flickr Weathering etc. by Robbert Jan., on Flickr IMG_20221015_194536 by Robbert Jan., on Flickr I mean, a serious difference since last time and now working towards the first show for it's debut. Regards, Robbert Jan.

The R&J Colliery (w.i.p.) Washing and weathering by Robbert Jan., on Flickr

Last week I managed to fit the windows to the Class 101, the etches where al cut out and filed smooth before a coat of primer and Tamiya ts-17 "gloss aluminum" Fitting window frames Class 101 by Robbert Jan., on Flickr Today I've applied all of the lining, a lot of work and something I've not done on this large a scale, the Fox lining pack was just enough for the 2 cars with a small amount remainging. Class 101 Striped and with Whiskers. by Robbert Jan., on Flickr Class 101 Striped and with Whiskers. by Robbert Jan., on Flickr With the whiskers in place it really looks the part and gives me the energy to proceed to the next challenge. Hope you enjoy! Regards, Robbert Jan.

Hello again, Yesterday looked like a good day to paint both body shells, with temperatures at a steady 20 degrees outside it was time to take the plunge. Painting the Class 101 green! by Robbert Jan., on Flickr A small amount of primer was applied to the areas that I have been working on such as the driprails and missing top hinges (left those of deliberately to make sanding the join between wall and roof easier) Then a quick dusting with the body up side down so the lower end of the walls is also covered appropriately. Painting the Class 101 green! by Robbert Jan., on Flickr And then it's a case of slowly building up the layers using Tamiya TS-9 "British Green" (I can't buy railmatch or any paint at all in the UK because of the policy that is in place regarding liquids etc) IMG_20220708_192018 by Robbert Jan., on Flickr IMG_20220708_192106 by Robbert Jan., on Flickr I've only found one or two spots that need a bit of tlc afterwards but otherwise it looks good and I'm happy so far, atleast to a point that I went and removed the masking to look for any overspray. IMG_20220708_192317 by Robbert Jan., on Flickr With just 1 spot where the green had managed to intrude in to the interior I was pretty pleased and after a few hours I took the last pictures on the garden railway sitting pretty on the underframes. IMG_20220708_194047 by Robbert Jan., on Flickr IMG_20220708_194108 by Robbert Jan., on Flickr IMG_20220708_193927 by Robbert Jan., on Flickr There is still heaps of work, the next job is the roof panels as these will become grey. The window frames are still stored and will be something that I'll tackle soon after I figure out how to gently bow the frames before inserting as I don't want them to be under constant tension. (they are etched and flat but the walls are slightly curved) Enough to do! Hope you enjoy, Regards, Robbert Jan.