RMweb Premium DavidLong Posted September 15, 2021 RMweb Premium Share Posted September 15, 2021 (edited) Anyone got any ideas for producing tall vacuum pipes for wagons. Like this: https://paulbartlett.zenfolio.com/?q=m422441 Rather than just a single bent piece of wire I wondered if anyone had any success with a bit of extra detailing. David Sorry, this question should have been in 'Any Question Answered'! Must concentrate . . . Edited September 15, 2021 by DavidLong Link to post Share on other sites More sharing options...
richbrummitt Posted September 15, 2021 Share Posted September 15, 2021 Did you already review the magazine article by the late Pete Wright, also reproduced in Loco bits and pieces, called 'Skirl o' the pipes'? 1 1 Link to post Share on other sites More sharing options...
Caley Jim Posted September 15, 2021 Share Posted September 15, 2021 (edited) For vacuum or steam heat pipes I coil some fine copper wire (single strands from bell wire) round the wire of the pipe to represent the corrugated section. You can make the outer end look like the wee connector. For Westinghouse pipes I use finer wire without the windings. Jim Edited September 15, 2021 by Caley Jim Spelling 1 Link to post Share on other sites More sharing options...
RMweb Premium DavidLong Posted September 16, 2021 Author RMweb Premium Share Posted September 16, 2021 21 hours ago, richbrummitt said: Did you already review the magazine article by the late Pete Wright, also reproduced in Loco bits and pieces, called 'Skirl o' the pipes'? I'd forgotten that, Rich. I'll have a check in my magazines. David Link to post Share on other sites More sharing options...
DuncanFogg Posted September 17, 2021 Share Posted September 17, 2021 I have a packet of phosphor-bronze guitar strings. The larger ones look like the coils on a vacuum pipe, the smaller ones are great for Simpson springs. No idea how to make any music from them though! Duncan 1 Link to post Share on other sites More sharing options...
2mm Andy Posted September 17, 2021 Share Posted September 17, 2021 There were a few posts on this subject in the "Any question answered" thread last year. Using wire-wound guitar strings seemed to be somewhat contentious! Building relatively few wagons (none at the moment!) I usually use the N Brass Loco castings. Andy 1 Link to post Share on other sites More sharing options...
Caley Jim Posted September 17, 2021 Share Posted September 17, 2021 Further to my earlier post, here are photos of one of David Eveleigh's GER yeast van kits before..... and after painting. Jim 3 1 Link to post Share on other sites More sharing options...
RMweb Premium DavidLong Posted September 17, 2021 Author RMweb Premium Share Posted September 17, 2021 6 hours ago, 2mm Andy said: There were a few posts on this subject in the "Any question answered" thread last year. Using wire-wound guitar strings seemed to be somewhat contentious! Building relatively few wagons (none at the moment!) I usually use the N Brass Loco castings. Andy Thanks, Andy. I knew that I had seen something about this subject but couldn't remember when it was. The suggestions on that thread are useful. I have checked in my stash of wires and found that I have a coil of Nickel Wound 0.508mm banjo strings made by Vega of Nazareth*, Pennsylvania which I remember that I bought from a music shop in Cambridge about thirty years ago! This is about 0.005mm bigger than Nick's 0.45mm copper wire. Just to be on the safe side I have got a couple of coils of the copper on the way to me via ebay. Now that I'm back home I will also check out Pete Wright's article as suggested by a couple of contributors. Many thanks for the suggestions both on this thread and the previous one from last year. David * Could this be the same Nazareth as in The Band's song 'The Weight'? "As I pulled in to Nazareth, was feelin' about half past dead". I guess we will never know . . . Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now