Evening All,
with about 95% of the welding and bodywork repairs now complete work starts to move on to the more cosmetic aspects of the locomotive
The front end repairs are now complete at No1 end and the locomotive is seen in its first (of 3 coats of undercoat) here we see it in its initial blue undercoat, this is to give the paint a good thickness and allow for lots of opportunity to fill imperfections as different shades of paint show them more easily, but also t
Dave the welder has run out of big bits to weld.....
We are now at the stage of where we now have lots and lots and lots of fiddly small parts that need to be sorted out, and if you watch something like car SOS this is where the time gets eaten up.....
The drivers side window getting much attention after more rot was found in the corner, the lower window frame and shelf have been replaced with metal.
Another view of the shelf, some q
We start where we left off...
Work has started to re-instate the metal strip which attaches the dome to the cab, the dome itself has been filled smoothed and flatted and given an initial coat of grey primer, the rough join will be hidden by aluminium trim....eventually.
The strip now extends above the drivers windscreen.
Over the past few years we have grown quite attached to rust and we were worried we were running out..
Work continues above the windscreens and the scabby metal has now been cut away and the metal below cleaned up to see what can remain and what needs to be removed, right to the base of the small section of angled steel above the centre windscreen, the screen itself covered to protect it from metal fragments during the cutting. The dome is pretty beaten up from years of pigeon and bird strikes but also previous repairs, you are looking at the original surface of the dome as evidenced by the br gr
We, start where finished last....
The top second-mans side window has now been fabricated and welded into place as well as the internal steelwork in this area, the cabling has also been encased in copex to protect it, these are the cables for the second mans switch panel and the brake indicator panel. More steel has been removed further up due to distortion that was being hidden by filler. Also as can be seen a steel plate has been welded on the second mans side.
First a bit of nostalgia :)
26043 2 weeks off the production line from BCRW and at the time was on commissioning trials, as 26043 is a series 1 class 26 it never had cab droplights fitted, we see the tablet catcher recess, and its front connecting doors, we also see that like all 26s its boiler fitted. Note it does not yet have the opening window instead it has a boiler filler hatch.
26/1s incorporated a number of weight saving measures, such as the cantrail
A bit of a change, i wanted to make sure that people were not getting tired by me just showing photos of metal being bashed, those blogs will continue as there seems to be a lot of interest in it. However in the last blog i invited some questions that people might have had about how things work in a Diesel Electric locomotive like the class 26, however all of the first generation diesel electrics work on pretty much the same principles so its very relevant across the fleet.
@37114 a
When you do the amount of bodywork we are doing, you almost go back through a locomotives history, like rings on a tree....and its interesting when the casual observer thinks something is a lot better than it really is.
043 on the turntable at minehead, everything you have seen....looks alright doesn't it...doesn't seem to show anything untoward with the bodywork.....everything you have seen....is there....everything your about to see.....is there....waiting to be discov
With the major welding complete to No2 end....its time to tackle what we always knew was there...no 1 end...
Dave the welder makes his first cuts into No1 end (he was reminded to put his goggles on after this photo was taken!) We see the rather optimistic hatched area we drew last week of metal we expected to cut.... the side panel itself doesn't look too bad at first glance....but...inspections at the base of the window show significant corrosion....
A bit of a while since my last blog, but no let up in the effort on 26043, work obviously fades over the summer months, its peak season for the diesel department so a number of us crew locomotives but we also have summer holidays and kids to look after...
The last sheets of steel being welded in, during late march at No2 end
No2 end welding is now complete all that remains is to fit a new skirt, the skirt is a very complex fabrication and is curved
We continue where we left off....
Dave the welder is putting replacement angle iron in the cab area, this will be used as something to not only strengthen the door pillar (and give it something to be attached to) but also as a base for a new cab skin to be welded on, most of the accident damaged pillar has now been cut aware ready for a replacement to be fitted.
The crib plates (as seen in the previous blog were completely rotten, they have been re
Evening all,
where did we leave off oh yes....the liners... (my previous blog is working, but due to the unfortunate issues on RMweb a lot of my photos have been lost on my previous blogs before that....hopefully over time i can upload the photos again).
After you install the liners....its best to get some confidence they have sealed...this typically involves filling the block up and leaving it for a period of time....hoping none of it escapes into the sump.....which is o
Since the last entry, the liners Pedro has worked his magic and the liners have arrived from sunny spain.
4 brand spanking new standard size Sulzer liners manufactured to the original drawings
The Liner interior showing the cross hatching and the carbon brake the end of the cross hatching marks the top of the travel for the top piston ring. At the top of the stroke the piston crown is roughly flush with the top of the liner.
The liner
Lockdown couldn't come at a worse time....26043s engine was in a stripped down state, and as a result the crankshaft (whilst protected) was exposed to air (due to the absence of the pistons) whilst protected I would have much preferred to have been able to go up to be able to keep the engine fully protected but national rules meant this had to be kept to a minimum, 26043 was also out in the yard at the time, and the engine had to be carefully sheeted over.
During lockdown I took the
A bit of a boring one really, as it concentrates more on a single part of the engine but ill try and bed it out a bit more with some more slightly interesting bits.....
A view of 26043s 6LDA with both side covers removed (reason why will be explained in a bit)
In this view you can see where the block is bolted to the crankcase, and you have a good view of the camshaft, there are 3 cam lobes per cylinder, the outer 2 of the lobes operate the pushrods and the