Two sets of 30 year old ex-LBSCR 4 car 4 wheeled carriages arrived on the Isle of Wight in 1924. They were followed later by some slightly newer Billington carriages, some of which still run on the Isle of Wight Steam Railway. The Stroudley sets saw less than 10 years service on the island, so are not really suitable for the period of my layout. But a set of etched brass bodies are available from Etched Pixels, so how could I resist.
Being only body kits, I needed some chassis that w
Built by the North London Railway in 1864 as a four compartment, all-first class, 4 wheeled carriage, this vehicle was purchased second hand, over 30 years later by the Isle of Wight Railway (IWR), along with six other carriages. It was numbered 46. It retained the varnished teak livery, but bore the garter motif of the IWR, with its number in the centre. One of the first class compartments was down-graded to second class. When the Southern Railway took over in 1923, these 60 year old carriages
OK, I know they did not survive into the 1950's but a 4 car set was used on the Freshwater line, so that is good enough for me. The brass etch for the bodies is available from Etched Pixels. They suggest putting them on chopped up peco wagon chassis, but I thought they would look nicer on etched chassis. The GWR 4 wheeler chassis from David Eveleigh is almost perfect for length. I could not figure out how to fit the footsteps provided, and the Stroudley set only had a single footstep, except bel
Well, I didn't give up. At the end of the last post, I had the chassis running nicely with the controller wired directly to the motor, but picking up from the rails was less impressive, despite the fitting of the 'Simpson spring pickups' rubbing on all the axles. The chassis was disassembled and re-assembled a few times, to no avail, and another crank pin came loose from a wheel and had to be re-soldered back in. Quartering the wheels was trickier as the motor was now solidly in place, but plent
Still making progress, and still making mistakes. The etched chassis does not include any provision for mounting the motor, but I spoke with Jerry Clifford at the Didcot exhibition who said he fits a piece of plastic onto the centre frame spacer, files a curved saddle into it and glues the motor to that.
I always want to be a bit different, so I thought a blob of Milliput might form a saddle without the need for filing. My first attempt started well, but as the Milliput took a long t
Having produced a free running chassis at the end of the last session, I had to disassemble it in order to add the 'Simpson Spring Pickups'. These are pieces of fine phosphor bronze wire, acquired by straightening out some unwanted N gauge coupler springs. They are soldered at one end into holes in the chassis and pass behind each bearing so they will rub gently on the axles with the absolute minimum frictional force. The axle muffs need to be shortened to make room, and must have smooth ends so
More slow progress this week, and a sense of achievement. To put this into perspective, I have to admit that in the 25 years that I have been a member of the 2mm Scale Association, I have attempted to build a number of chassis for a variety of locomotives, using several different techniques, none of which were completed. I had at least 5 tries at making a chassis for an S15, using phosphor bronze strip for frames, as was recommended in those days. I just could not drill and ream holes without th
I have now received a new set of wheels of the correct diameter (8mm) and I have given them a quick spray of primer (one set black for my second Terrier and this set grey for painting green and black for my Southern livery Terrier).
The next job on the chassis was to drill out the 0.3mm holes for fitting the brakes and the 'Simpson Spring' axle pickup wipers. Two of the brake support holes require drilling into the side of a glass fibre PCB spacer. Typically, my drill bit
As anyone who has seen my layout at exhibitions can tell you, so far some very unlikely motive power has been operating the Freshwater line of the Isle of Wight. I do intend to rectify this, but getting the layout operating smoothly, and scenery added were higher priority. I have acquired some Dapol A1X Terriers (one at least with the correct extended bunker) ready to be converted to 2mm finescale. Many months ago I started work on modifying the original chassis, as per an article in the 2mm Sca
