As we all know, the best way to ensure that the RTR manufacturers will release something we want is to build a kit version. So it was that on the thread about the new Bachmann 7F, when thoughts turned to what might appear next, I jokingly suggested that I should get on with building my Craftsman 1P kit that has been languishing on the shelf for some time. Then, after Xmas I felt that I needed a break from scenery and ballasting on Nowhere, I thought about it a bit more and decided to give it a go. What follows is the first part of the story of building this now quite ancient kit.
The first photo shows a representative sample of the brass and nickel silver parts in the kit (only one of each duplicated part). As can be seen, the cab roof and boiler are roughly pre-rolled and a few parts that need right-angle bends are half-etched to aid bending. There are also a few slots and tabs to help get things in the right place. All of these are a good fit with the slots etched to just the right size for the tabs. From comments elsewhere, this is not always the case with this style of construction. Other half-etching provided for rivet/bolt embossing in the smokebox wrapper and buffer beams, but there is no other rivet/bolt detail on the brass parts.
The first problem for a modern builder is the chassis. This was designed to take an XO4 type motor sitting at an angle to the footplate and filling most of the cab. Indeed, there is also a cutout in the bunker top/front panel to accommodate the motor. I will probably be using a Mashima motor with a High Level gearbox so, on the one hand there is scope for some modification to enable the cab interior to be modelled, but on the other it is unlikely that the chassis frames with their sloping motor support will be of much use in this build. For now, I'll leave that problem aside and get on with the body.
The main parts went together quite well and soon I had a footplate with buffer beams, valances and steps supporting a bunker and side tanks. In the next photo it should be clear that I've filled in the motor gap in the front of the bunker and added inside faces to the side tanks within the cab area -- spot the 'deliberate' mistake, of which more later
As I mentioned above, the boiler came roughly rolled to shape, but needed some tweaking. The brass was quite hard, so needed annealing first. I added a fillet of brass strip along the inside of the joint at the bottom of the boiler just to add a bit of strength. I then added the boiler bands using some phospher bronze strip included in the kit. Perhaps there was just enough strip to do all of the bands, but by the time I had cut off a bit that acquired a nasty kink, there was not enough to do all of the bands. Since the photo was taken, I've noticed that two of the bands were not as straight as they could be and have corrected this. The final band just in front of the cab was also added from some strip in my stock.
The boiler was then attached and it was beginning to look a little like a Johnson loco. Next, I fitted the cab, but not the roof, and my thoughts turned to internal details. I have a fairly plain white metal backhead that could be turned into something approximating to one of the photos in Essery & Jenkinson, "An Illustrated Review of Midland Locomotives, Volume Three". However, looking at these photos and the drawings in this volume and in James, Hunt and Essery, "Midland Locomotives", No. 1, I realised the error mentioned earlier Inside the cab, the side tanks only extend back about half the length of the outside sheeting. So, the brake standard which is clearly visible in many photos of the left-hand side is almost at the rear of the tank. I had blindly followed the lead given by the tank rear/top/front piece in the kit which extended almost to the door opening, about 5mm too far. Studying the drawings, I realised that this space was filled with a couple of what appear to be toolboxes or seats that are only about half of the height of the tanks.
So, out with the blowtorch (gas soldering iron) to remove the cab sides/rear and my tank infill. Then some careful cutting at the correct place with a razor saw and further application of the gas flame saw the unwanted metal removed. The tank backs and inner sides were re-instated in the correct position.
The dome, Salter valves and whistle are Gibson brass castings rather than the white metal parts provided in the kit. Now all it needs is to clean up the mess created by the 'adjustments' and I can get on with the next stage.
Oh, by the way, I mentioned the S&DJR at the start and this engine is intended to be 58047, the longest surviving 1P with round-top firebox and Salter valves, as Ivo Peters reminded us on many occasions
- 7
7 Comments
Recommended Comments
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now