Hi guys
I was wondering if someone can help me out as i have a little problem with my Hornby R8247 point decoder as in useing the elink controler with railemarster software ?
Its ony just started hampering every time i connect the decoder to my track bus line i keep getting a on the
Error message on the screen an the light on the elink keeps flashing
Telling me i have a short somewhere i have disconnected all the points so it must in the decoder it self i was wondering if the is someway i can reset it or something?
So i wondering if someone has had this problem as well an can help me out ?
I really look forward to hearing from you
Gavin
From Australia
Thank you RAF 96 for your reply i really appreciate it
But my as a other question ?
As i dont quite understand what your mean by writing the value 8 or cv8 to the decoder as i understand that have to contact it to the program track just the cv bit i dont quite understand hopefully you can help me out ?
But once again thank for taking the time to reply to me as i really appreciate it
Gavin
Hi guys
I was wondering if someone can help me out as i have a little problem with my Hornby R8247 point decoder as in useing the elink controler with railemarster software ?
Its ony just started hampering every time i connect the decoder to my track bus line i keep getting a on the
Error message on the screen an the light on the elink keeps flashing
Telling me i have a short somewhere i have disconnected all the points so it must in the decoder it self i was wondering if the is someway i can reset it or something?
So i wondering if someone has had this problem as well an can help me out ?
I really look forward to hearing from you
Gavin
From Australia
Befour i go into detail i thought id as regards to signals are you formula with how to set up signals on the Hornby railemarster useing the elink as my controller ?
Hi guys
I was hoping someone may be help me out
As im looking at adding light signals red &green signals to my Hornby railemarster system as im useing the Hornby elink as my controller as iv been told i need to use a tran tec
SC1 Dual 2 Aspect ...if so thats fine but i just wondering if there is any other way this can be done with out useing the train tec device
Look forward to hearing from you
As id really appreciate it
Thanks again
Hi guys
I was hoping someone may be help me out
As im looking at adding light signals red &green signals to my Hornby railemarster system as im useing the Hornby elink as my controller as iv been told i need to use a tran tec
SC1 Dual 2 Aspect ...if so thats fine but i just wondering if there is any other way this can be done with out useing the train tec device if so id love to know
Look forward to hearing from you
As id really appreciate it
Thanks again
Hi
Thank you for your reply i totally understand what your saying as i just thought there may have been another way of doing it
Look forward to hearing from you
Gavin
Hi guys
I was hoping someone may be help me out
As im looking at adding light signals red &green signals to my Hornby railemarster system as im useing the Hornby elink as my controller as iv been told i need to use a tran tec
SC1 Dual 2 Aspect ...if so thats fine but i just wondering if there is any other way this can be done with out useing the train tec device
Look forward to hearing from you
As id really appreciate it
Thanks again
Gavin
hi all
i hope i don't sound a little silly but i checked out the the manual an it only covers the Hornby Select an the Elite nothing there to tells you how anything regarding the Hornby e link controller
as im using the e link it with Hornby rail master software
so i was hopeing you may be able to help me out with this please mate
look foward to hearing from you
Thank you Gavin
hi guys
im hoping someone can help me out as im using an a R8247 decoder for my points an it works well
but i have been reading in the Forums that you are able to change it from a short high power burst of power to a continuous output feed of power
witch is exactly what i'm looking for
as i have read the instructions that with it but i've noticed there is nothing there to tell you how to Chang i to continuous output feed of power
regarding the Hornby e link controller as im using it with Hornby rail master software
as im hoping sumone is able to help me out with this please
look foward to hearing from you
Thank you Gavin