Quarryscapes Posted October 26, 2017 Author Share Posted October 26, 2017 And a comparison of connecting rods - ginormous Slater's on the left, dainty 3DP ones on the right. 6 Link to post Share on other sites More sharing options...
timbowilts Posted October 26, 2017 Share Posted October 26, 2017 How much of the original kit is going to make it into the final build? Curious of Calne Link to post Share on other sites More sharing options...
Quarryscapes Posted October 26, 2017 Author Share Posted October 26, 2017 How much of the original kit is going to make it into the final build? Curious of Calne Good question... Tank, Bunker and Valve gear have been replaced altogether, Main frame has been hacked up to accept new ones, but the rest is pretty much as intended, a few new holes here and there for wiring and extra screws. I'll have spent more on new parts than I did on the kit in the first place by the time it's done, but the same was true of Red Damsel too! At least this time, the money hasn't mostly gone on rivets! 1 Link to post Share on other sites More sharing options...
Quarryscapes Posted October 31, 2017 Author Share Posted October 31, 2017 Tank and bunker from i.Materialise. I grew tired of waiting (been over a month!) and yesterday ordered some tweaked designs from Hexa³ done on a Form 2. Today the i.M parts turned up. I think the Form 2 prints will end up on the model rather than these, we'll see which has the better finish. 6 Link to post Share on other sites More sharing options...
Quarryscapes Posted November 3, 2017 Author Share Posted November 3, 2017 Form 2 prints - including a characteristic Pen yr Orsedd teapot oil can! 14 Link to post Share on other sites More sharing options...
Quarryscapes Posted November 5, 2017 Author Share Posted November 5, 2017 New livery being applied.... 10 Link to post Share on other sites More sharing options...
Phil Copleston Posted August 27, 2018 Share Posted August 27, 2018 (edited) Just discovered this thread and am now following. Most interesting as I am considering buying this Slater's kit and making similar mods. Any updates on construction? Edited August 27, 2018 by Phil Copleston Link to post Share on other sites More sharing options...
Quarryscapes Posted September 6, 2018 Author Share Posted September 6, 2018 Just discovered this thread and am now following. Most interesting as I am considering buying this Slater's kit and making similar mods. Any updates on construction? Nothing further to add yet, the new valve gear still needs purchasing which is having to wait as I've just been investing heavily in camera & extra lighting equipment for work, which should allow me to spend less of 'my' time working form home. All the parts I've designed are available on SHapeways hould you need them. Link to post Share on other sites More sharing options...
Quarryscapes Posted March 7, 2019 Author Share Posted March 7, 2019 Over a year since anything was last done to Gelli, it's criminal I know...however progress has been made. This week I have had some free time, so out came the lathe and the machining of the crossheads and slidebars is now in progress. I still need to order the replacement valve gear mind, and some 1.5mm silver steel for the piston rods. 9 1 1 Link to post Share on other sites More sharing options...
Quarryscapes Posted March 14, 2019 Author Share Posted March 14, 2019 Piston Rod No.1 has been united with a crosshead. It's formed of 1/16" silver steel with the end turned down to be a push fit in the crosshead and is secured with bearing retainer. The hole in the gland was drilled 1/16" which theoretically should have been a nice loose fit but no, I seem to have found undersized drill bits and its actually taken a lot of polishing to get the rod to slide through, and will no doubt take some more once there's a crosshead hanging off it, despite doing all I can to keep it concentric (It's sat in the lathe whilst the retainer cures!) 10 1 Link to post Share on other sites More sharing options...
Ruston Posted March 18, 2019 Share Posted March 18, 2019 This is amazing work here. When you're talking about 3D-printed slidebars and rods being steel, do you mean actual steel? They can 3D print using actual metal, or have I misunderstood? 1 Link to post Share on other sites More sharing options...
Quarryscapes Posted March 19, 2019 Author Share Posted March 19, 2019 On 18/03/2019 at 10:06, Ruston said: This is amazing work here. When you're talking about 3D-printed slidebars and rods being steel, do you mean actual steel? They can 3D print using actual metal, or have I misunderstood? Yes, actual Stainless Steel, in powder form sintered together roughly with a laser and then injected with molten bronze to actually keep it together. It's a very strange material to work with, requires solid carbide tools. The slidebars ended up being trued with a grinding disc rather than the planned milling cutter simply to avoid the flutes catching on the edges of the slidebars and deflecting rather than cutting. The Brass items are lost wax cast the traditional way, but from 3D printed investments rather than hand carved or moulded ones. 1 Link to post Share on other sites More sharing options...
Paul_in_Ricky Posted September 2, 2022 Share Posted September 2, 2022 Did this model ever get finished Alan ? I'm just starting on one and it's such a loss that so many of your photos have disappeared from the thread. It was a great resource. Looks to be an 'interesting' build given the omissions in the instructions. Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now