RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 Cork down and work on the lighting rig underway. The two wedge shaped pieces sit on the end boards and project the fascia about 50mm in front of the layout. It is designed to be easy to slot on and off as the layout is stored in a 77L RUB. 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 The fascia 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 (edited) The joint between FY and main board. I use 3mm ply set into the 3mm cork to provide a firm foundation for the track. I have found that some "3mm" ply is not and I carefully preserve my small stock of the correct wood for jobs such as this. More brick action... Edited March 17, 2021 by Gilbert 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 A bit more woodwork... 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 (edited) and a bit of paint.. I try to make parts easily fitted and removed. Apart from the front profile board fitted at the end of the build everything else is fitted in place with small M4 and M5 machine screws, wing nuts and in some case pronged tee captive nuts Edited March 17, 2021 by Gilbert 3 1 Link to post Share on other sites More sharing options...
RMweb Gold mudmagnet Posted March 17, 2021 RMweb Gold Share Posted March 17, 2021 Great progress. 1 Link to post Share on other sites More sharing options...
RMweb Premium ELTEL Posted March 17, 2021 RMweb Premium Share Posted March 17, 2021 3 hours ago, Gilbert said: Hi Terry - All small Code 75. I've also found that this orientation with the RH turnouts rather than LH is much better in use with the Kadee couplers I use. 1. I’m Just wondering what the theory is behind why Kadee works better with RH points ? 2. Will you be using one under track kadee magnet as highlighted in blue or three as kadee under tracks magnets as highlighted in pink ? What are the advantages and disadvantages of each option ? Terry 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 (edited) 26 minutes ago, ELTEL said: 1. I’m Just wondering what the theory is behind why Kadee works better with RH points ? 2. Will you be using one under track kadee magnet as highlighted in blue or three as kadee under tracks magnets as highlighted in pink ? What are the advantages and disadvantages of each option ? Terry Hi Terry - jumping ahead in the project to a later photo - there are 2 magnets. The main one is located where stock being shunted into the two front sidings is orientated so the curve exaggerates the coupler opening (ignore the nearest line - it will be a cement siding not usually included in the Inglenook game) I don't use magnets below the track as I find they are too strong for most British stock with steel axles and cause a shuffle as the wagon passes over it. I suspect an electromagnet or a hinged magnet would work but I'd probably need a foot pedal to get everything coordinated! Edited March 17, 2021 by Gilbert 1 Link to post Share on other sites More sharing options...
RMweb Premium ELTEL Posted March 17, 2021 RMweb Premium Share Posted March 17, 2021 We had a similar problem on the club narrow gauge layout “Seagone” and we opted for the hinge magnet which seems to work fine. I think somewhere I have electromagnet so I’ll give it a test. I have heard of modellers placing a foam pad above the wagon axle to stop the shuffle . I will keep you posted..... Terry 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 17, 2021 Author RMweb Gold Share Posted March 17, 2021 22 minutes ago, ELTEL said: We had a similar problem on the club narrow gauge layout “Seagone” and we opted for the hinge magnet which seems to work fine. I think somewhere I have electromagnet so I’ll give it a test. I have heard of modellers placing a foam pad above the wagon axle to stop the shuffle . I will keep you posted..... Terry Cheers Terry - Yup...I've used the foam brake trick as well - also in 7mm with S&W couplings I've also trialled a Rapido switchable uncoupler but although I have not opened it up I think magnets move into place when activated - unfortunately they also seemed strong enough to attract axles when "off". Link to post Share on other sites More sharing options...
Off Tackle Posted March 17, 2021 Share Posted March 17, 2021 8 hours ago, Gilbert said: Hi Terry - jumping ahead in the project to a later photo - there are 2 magnets. The main one is located where stock being shunted into the two front sidings is orientated so the curve exaggerates the coupler opening (ignore the nearest line - it will be a cement siding not usually included in the Inglenook game) I don't use magnets below the track as I find they are too strong for most British stock with steel axles and cause a shuffle as the wagon passes over it. I suspect an electromagnet or a hinged magnet would work but I'd probably need a foot pedal to get everything coordinated! Oooo liking where this is going... Regarding Kadees, I don't know if this will be any help to anyone, but here's a link to some experiments with magnets etc. The main finding is de-magnetizing wagons by swapping out the axles for brass ones - I can't emphasize enough the hugely positive impact this has had on shunting operations and its pretty straightforward. 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 18, 2021 Author RMweb Gold Share Posted March 18, 2021 8 hours ago, Off Tackle said: The main finding is de-magnetizing wagons by swapping out the axles for brass ones - I can't emphasize enough the hugely positive impact this has had on shunting operations and its pretty straightforward. I have got some of the brass axles and agree they are a major improvement. Interesting to see how you cut the magnets with a knife. Hadn't thought nof that! 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 18, 2021 Author RMweb Gold Share Posted March 18, 2021 Full size plan out again to sort out wiring and PMs. The inputs for point motors and DCC are located at the rear. The NCE PCP panel will go in the front fascia. A lesson learnt - the Point Controls will be in a small panel set into the Fiddle Yard. This is easy too use but also means the layout PMs etc can't be tested without attaching the FY. On Dock Street I used a small tethered box which could be connected to the layout if required for testing etc. but was normally "permanently" attached to the shunting track. I think this is actually the best solution for my configuration and I may modify Cropper Street accordingly. 3 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 I pre-wired the track once it was cut to size. 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 and a bit more testing... 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 I've been experimenting with Modeltech board joiners and I'm very pleased ( I event sent him some US Code 83 which I think means he's now added those to his range) 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 (edited) Track down and droppers in place Edited March 21, 2021 by Gilbert 3 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 A bit of testing...I suspect this loco is a bit early for the Cement siding but Rule 1 may apply..its got sound and stay alive by Digitrains and its a gem. 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 Now its getting serious... 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 This is the underneath of the FY with the integral point control panel. As previously suggested I may review this arrangement. 2 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 20, 2021 Author RMweb Gold Share Posted March 20, 2021 I was minded to try the Scalescenes arches but although the trial piece turned out OK I couldn't face all that cutting of the cardboard. Since then I understand some one is providing laser cut card parts and I've discovered self adhesive matt photo paper for printing in my High Street computer shop...maybe next time - its nice stuff. 2 Link to post Share on other sites More sharing options...
RMweb Gold Mick Bonwick Posted March 22, 2021 RMweb Gold Share Posted March 22, 2021 On 20/03/2021 at 18:25, Gilbert said: Since then I understand some one is providing laser cut card parts Here you are: https://www.chrisinden.co.uk/product-page/laser-cut-parts-for-scalescenes-low-relief-arches 1 Link to post Share on other sites More sharing options...
RMweb Gold NHY 581 Posted March 22, 2021 RMweb Gold Share Posted March 22, 2021 On 20/03/2021 at 18:18, Gilbert said: Now its getting serious... On 20/03/2021 at 18:20, Gilbert said: This is the underneath of the FY with the integral point control panel. As previously suggested I may review this arrangement. Bloody Hell !! 1 Link to post Share on other sites More sharing options...
long island jack Posted March 22, 2021 Share Posted March 22, 2021 What's your backup, if one of those point motors fail at 11am on a Saturday morning of the exhibition. That's always at the back of my mind when planning/building a exhibition layout, which is why i always use manual point control, bike spoke, WIT ETC, which isn't a 100% reliable, but i've only had one failure, in all the years of exhibiting and it was a 5 min fix, KISS. Just asking!!!! 1 1 Link to post Share on other sites More sharing options...
RMweb Gold Gilbert Posted March 22, 2021 Author RMweb Gold Share Posted March 22, 2021 2 hours ago, long island jack said: What's your backup, if one of those point motors fail at 11am on a Saturday morning of the exhibition. That's always at the back of my mind when planning/building a exhibition layout, which is why i always use manual point control, bike spoke, WIT ETC, which isn't a 100% reliable, but i've only had one failure, in all the years of exhibiting and it was a 5 min fix, KISS. Just asking!!!! In my defence I would offer the following evidence: I have Cobalts on a number of layouts and have had no problems - I think they have a good reputation. CS is a very simple layout to maintain or repair. It can be flipped over in no time at all and stood on its rigid backscene once the plug in lighting rig is removed. I take spare PMs to a show so it should be easy to replace. The 90 degree adapter and operating wire can be transplanted easily. Removing one of the locating screws would allow the new PM to be aligned fairly easily. The only thing that would improve things would be to make the wiring connection a male female plug in chocolate block connector. Going to the trouble of doing this will guarantee the PMs never need replacing - obviously. In any case I will not be under a layout with a torch fighting gravity... Just answering..... 2 2 Link to post Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now