MikeTrice Posted January 21, 2015 Share Posted January 21, 2015 I have been describing a conversion of a Bachmann HO Emily to look something closer to the GNR Stirling Single on which she is based (http://www.rmweb.co.uk/community/index.php?/topic/94209-emily-laid-bare-a-stirling-effort/page-1). One of the techniques I used was to use pounce wheels to emboss rivets in styrene. This attracted some small attention so rather than bloat Emily with further details I thought it would be easier to start a new topic. This all came about some time ago when I was trying to improve the chimney in a 1/25th scale kit of Stephenson's Rocket. For that exercise I use the dressmaking wheels used for transferring patterns which are quite coarse and are typically referred to as tracing wheels. Looking at the term "pounce wheels" results in a similar tool but with a much finer tooth that is used in tracing artwork. So without further ado here are a selection: In the photo above, from top to bottom, you have: Excel 24 tpi Grifhold 21 tpi (No 9) Excel 18 tpi Grifhold 15 tpi (No 12) They are ideal for embossing rivets into 5 or 10 thou styrene as you can see here. The styrene is placed on a cutting mat and the pounce wheel run along the back under pressure against a steel rule. In this instance the styrene has been trimmed to provide wagon strapping (an older 10p coin is included for comparison with its "rivets"): An example of a rivetted footpalte from my Emily thread is shown here. The first row of rivets is embossed in 10thou styrene, then the piece turned though 90 degrees. By feeling with one of the pounce wheel teeth and existing rivet, it is possible to line it up for another row: Here is a test piece done using the four pounce wheels shown in the first image: And after a quick spray of primer: Another technique I have used with Emily is to emboss some rivets then shave them off with a scalpel and glue the shaved rivets onto Emily with solvent: A quick comparison of embossed rivets, in this case down to 21 tpi against a GBL GWR tender: Although I have only used styrene here I have successfully used the technique on thin brass (5 thou) and copper foil. The Excel pounce wheels had to be ordered from the States but they did come quite quickly. One problem with most of them is the small size of the head which is too small to use a normal steel rule. Instead I have to use a 6" one which is thinner. Link to post Share on other sites More sharing options...
RMweb Premium Siberian Snooper Posted January 21, 2015 RMweb Premium Share Posted January 21, 2015 I have some pounce wheels somewhere safe, I have yet to use them. This is the first time I have seen the results of their use. I have a steel bridge to build shortly, so I will need to find them based on your results, they should make the job relatively painless. I look forward to seeing further results in this thread. Thanks for the info Mike. Link to post Share on other sites More sharing options...
Andy Y Posted January 21, 2015 Share Posted January 21, 2015 Thanks Mike, a reminder I should get a range in rather than relying on one size fits all. I have some ponce wheels somewhere safe, Worth making sure you don't suffer typos when you go out asking for any. Link to post Share on other sites More sharing options...
RMweb Premium Siberian Snooper Posted January 21, 2015 RMweb Premium Share Posted January 21, 2015 Thanks Mike, a reminder I should get a range in rather than relying on one size fits all. Worth making sure you don't suffer typos when you go out asking for any. Duly edited, thanks Andy. Link to post Share on other sites More sharing options...
BS4Boy Posted February 15, 2015 Share Posted February 15, 2015 I use this https://www.whiteensignmodels.com/p/RB+Productions+RivetR+Rivet+Tool+RBT009/5856/#.VOBwEcMYaP0 for smaller rivets on .3mm plasticard. Also simply running it over any plastic surface will give an impression of a rivet line (obviously it would not be a raised rivet in this case but it does a very fast good enough look) Link to post Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.